Bosch ICP-COM-IF Manuale utente

Description of the ICP-COM-IF Module

The ICP-COM-

IF Module allows an isolated connection to be created between the MAP5000 (Interface

Module DE) and an external communicator (for example the AT 2000) via the parallel S1 interface. The

ICP-COM-IF Module offers:

Notes for installation

-The ICP-COM-IF Module can be mounted on the hinged mounting plate or the mounting rails of the

MAP control panel housing.

-A clearance of 15 mm is required on either side for subsequent wiring. Pull to disconnect the

connectors.

-The enclosure of an external transmission unit has to be mounted side by side to the panel enclosure

where the ICP-COM-IF module is mounted.

Mounting

1. Hook the ICP-COM-IF Module carrier plate into the existing breadboard of the

hinged mounting

plate or onto the mounting rails.

2. Use the screw provided to secure the carrier plate to the bottom rail.

•Seven outputs:

The output signals from the MAP Interface Module DE

control the ICP-COM-IF Module relays that provide isolated

changeover contacts (R1 to R7)

•Two inputs:

The inputs ST and R (for the "Communicator fault" or

"Negative confirmation" signals, for instance) can be

controlled via the following:

- isolated contacts

- C points (isolated via optocouplers)

Technical specifications

Rated voltage +10 to +28 V DC

Rated current

67 mA at 28 V or 180 mA at 10 V

Relay contacts rating 3 A/120 V AC, 3 A/28 V DC

Temperature range −25 °C to +55 °C

Weight 198 g

Dimensions (L x W x H) 132 mm x 85 mm x 20 mm (5.2 inches x 3.3

inches x 0.8 inches)

Bosch Sicherheitssysteme GmbH

Robert

-Bosch-Ring 5

85630 Grasbrunn

Germany

www.boschsecurity.com

32014/11

ICP-COM-IF

Installation guide

VdS class C G 111040

EN 50131

-2-6 Grade 3

Jumper settings

The inputs ST and R can be controlled via the following:

•isolated contacts

•C points (isolated via optocouplers)

To control the inputs via external "isolated contacts" or "C points", the jumpers must be

connected as follows:

Input Jumper setting Description

ST Control via isolated contact (factory default)

R Control via isolated contact (factory default)

ST Control via C point

R Control via C point

Relays

Output/input

Stand-by mode

Activation with

Output for the communicator alarm line ML1

Summary alarm

Output for the communicator alarm line ML2

Off

Duress

Output for the communicator alarm line ML3

Off

Holdup

Output for the communicator alarm line ML4

Intrusion/Tamper

Output for the communicator alarm line ML5

Summary Trouble

Output for the communicator alarm line ML6

Off

Fire

Output for the communicator alarm line ML7

Off

Armed (any area)

Input from external communicator

Communicator fault

Input from external communicator

Negative confirmation

ssysteme GmbH, 2014

32014/11

Relay 1

AT 2000

Relay 2

Remote communicator, for example the AT 2000

R1A

R1B

R1C

C1C

ML7

ML6

ML5

ML4

ML3

ML2

ML1

AT 2000 programming

•

Relay 1: "Continuous activation", stand-by "on"

•

Relay 2: "5 seconds", stand-by "off"

•

ML1–ML7: Conventional Lines Intrusion

Relay 2:

Negative

confirmation

Relay 1:

Communicator fault

C1B

C1A

ICP

-COM-IF

MAP Interface Module DE

The ribbon cable is

ttached to the MAP

Inter

face Module DE

Parallel S1 in-

terface

Red

marking at

top

The size of the terminal resistors (RE) to be looped in

depends on the communicator (for example 10 k for the AT 2000).

Pull to disconnect the connectors.

ML2

ML3

ML4

ML6

ML5

Red

arking

at top

Altri manuali Bosch Unità di controllo

Bosch

Bosch D7039 Manuale utente

Bosch

Bosch GCY 30-4 Professional Istruzioni per il montaggio

Bosch

Bosch PowerBox PBX 190 Manuale utente

Bosch

Bosch Rexroth IndraDrive CSB02 Manuale tecnico

Bosch

Bosch Rexroth IndraControl Manuale utente

Bosch

Bosch C-IR 20 Manuale utente

Bosch

Bosch CM746B Come usare

Bosch

Bosch rexroth PSK Gen 2 Manuale utente

Bosch

Bosch AEC-AMC2-UL1 Manuale utente

Bosch

Bosch rexroth WE6 5X Series Manuale utente

Bosch

Bosch Professional GCY 42 Istruzioni per il montaggio

Bosch

Bosch Rexroth ID 200/C-PDP Manuale utente

Bosch

Bosch FLM-I 420-S Manuale utente

Bosch

Bosch D8128D Manuale utente

Bosch

Bosch D8125 Istruzioni operative

Bosch

Bosch Rexroth DB 52 3X E Series Manuale utente

Bosch

Bosch Rexroth IMpnio Manuale utente

Bosch

Bosch Rexroth IndraControl L10 Manuale tecnico

Bosch

Bosch CM744B Come usare

Bosch

Bosch Rexroth 3DREP 6 XE Series Manuale utente

Bosch

Bosch MAP Control Center IUI-MAP0001-2 Manuale utente

Bosch

Bosch Rexroth SB24/34 Manuale utente

Bosch

Bosch Control 8311 Manuale utente

Bosch

Bosch B901 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente