39. Tone Out: Output of the Stripper.
40. Output 1-4 (40-43): Outputs of the
Distributor/ Reshaper.
44. Input A: Rear panel time code input.
22. Drop Frame LED: On solid for drop
frame code; blinks mostly on for miss-
ing DF flag (bit 10); blinks mostly off
for false DF flag; off for non-drop.
23. Video Code LED: On solid if code is
synchronous and in phase with video;
blinks mostly on if code is out of
phase; blinks mostly off if code is drift-
ing; off if no video is present.
Stripper
24. Source Select: Selects the input of the
Stripper: Code / Video / AC Mains.
25. Output Level: Adjusts the Stripperʼs
output level from full off to +12dbU
26. Output Waveform: Determines the
waveform of the stripped tone: Square
wave / Sine wave.
16. Reader (8 digit display): Reads
time code, user bits or video phase;
identifies the error type and the faulty
address.
17. Counter (4 digit display): Reads the
frame rate (fr/sec) of the incoming time
code or the frequency (hz) of Tone in or
To ne o u t.
18. Fr/Sec LED: On when 4 digit display
counts frame rate.
19. Hz LED: On when 4 digit display
counts frequency.
20. ASCII LED: On when ASCII flags are
set. On means User Bits are ASCII;
off ,User Bits are Hex.
21. Color Frame LED: On when Color flag
is set (bit 11 ); off when flag is not set.
35. Dipswitches: Future upgrades - pg 9
36. Serial Port: DB-9M for RS-232 I/O.
37. Parallel Port: DB-25F for Centronics
printer output.
38. Relay out / in: TRS 1/4” for remote
“Good Code” LED or extʼl trigger input.
INPUT B OUTPUT 5
TONE STRIPPERDISTRIBUTOR / RESHAPER
2 3 4 5
1
I_]dWb?d
=eeZ9eZ[ SOURCE
SELECT OUTPUT
LEVEL
OUTPUT
WAVEFORM
IH#'+!
J?C;9E:;
:?IJH?F7BOP;H "2!).34/2-
%,%#42/.)#3).#
ICFJ;
(+¦i
IgkWh[
'¦i
;8K
+&¦i
7
H[Wh
8
<hedj 9eZ[
L_Z[e
CW_di IgkWh[I_d[
INPUT
SELECT
OUTPUT
RISE TIME <hedjFWd[b
OUTPUT LEVEL
>h C_d I[Y <h
CODE ANALYZER
>p
9ebeh<h$
:hef<h$
L_Z[e9eZ[
%<h[gk[dYo
9eZ[ L_Z£
Jed[
_d Jed[
ekj
7I9??
9eZ[ <hWc[HWj[
<h%I[Y
H;7:;H
9EKDJ;H
E\\
Ki[h
Ed
8;;F;H
H;I;J
POWER
AUX I/O INPUT
"
22 23
17
35615 18 19 24 26
25
12478910 11 14 16 20 21
13
12
27
115 Vac
123 45 678
Loop
Input Input Loop
757
Off
VIDEO REFERENCE
Iso Grnd
Ground
Lift
Ã>Ìi`
ÀÕ`i`
INPUT A
OUTPUT 1OUTPUT 2OUTPUT 3OUTPUT 4TONE OUT
JIH
RELAY
OUT/IN
VID OUT
COLOR ID
ANALYZER
XLR Pins:
1=G / 2=H / 3=L
Fuse, Slo-blo:
T 200mA @ 115VAC
T 100mA @ 230VAC
(Optional)
Parallel Serial
Termination
42
41
43
39
40
44
28
30
29
34
35
36
38
37
33
32
31
Rear Panel
28. Voltage Selector & Fuse drawer:
Selects 115VAC or 230VAC & holds
the main fuse and a spare.
29. Power In: IEC 320 power inlet.
30. Ground Lift Switch: Isolates chas-
sis ground from signal ground.
Aux I/O
1. Input B: Auxiliary time code input, for
easy front panel access.
2. Output 5: Auxiliary time code output,
for easy front panel access.
Input Section
3. Input Select: This switch determines
which input is active (front or rear).
4. Signal In LED: Lights up when signal
is present at the selected input. Any
signal above -30db lights this LED.
5. Good Code LED: Lights up when
valid code is present at the selected
input; blinks off momentarily if a
“Fatal” time code error is detected.
Power
27. Power Switch: Turns power on or off
Distributor
6. Rise Time Switch: Changes the
waveform of all 5 reshaped time code
outputs: SMPTE = 25µsec, square wave
= 1µsec and EBU = 50 µsec.
7. Output Level (7-11): Adjusts the level
of each reshaped output individually
from full off to +12dbU.
Analyzer
12. Reset Switch: Push button to reset
SR-15+ or clear displays.
13. Beeper switch: turns beeper off.
14. Reader Select: Selects the mode of
the 8 digit display: Time code/ User
bits/ Video ø.
15. Counter Select: Selects the input and
the mode of the 4 digit display : Code
/ Tone in / Tone out.
31. Color ID In & Loop: Input & loop for
color field ID pulse.
32. Termination: 75Ω for video in & loop.
33. Video Reference In & Loop: BNC
jacks for video reference.
34. Video Out (optional): Report output.
