CoolGear CG-7PU3MGD Manuale utente

7 Port Managed USB 3.2 Gen 1 Hub w/

15KV

ESD Surge Protection

Model No. CG-7PU3MGD

Thank you for purchasing this 7-port Managed USB3.2 Gen 1 hub. The

Super-speed Hub is supplied with managing software utilities which can turn

on/off the bus power of each downstream device or even reset the entire hub by

user or application programs. It enables the success of your critical USB

applications instantly and improve your investment returns.

Features:

✓Compliant with USB Specification 3.2 Gen 1

✓Metal Case, DIN Rail and wall mountable

✓Software Manageable Bus power for each Port

✓Supports software utilities for Windows (XP and newer), Linux

✓Provides 7 Downstream USB3.2 Gen 1 Facing Ports (see Note 1)

✓Provides 7 LEDs Indicating each bus power states

✓Supports 5Gbps (Super-speed), 480Mbps (High speed), 12Mbps (Full-speed)

and 1.5Mbps (Low-speed) Speed

✓Supports 15KV ESD Level 4 Protection for Each Port

✓Supports +7~48V DC Wide Range Input Power

✓Supports USB Battery Charging v1.2 : CDP, DCP modes

1. Introduction

7-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit

1. USB-A Downstream Facing Port Connectors: There are 7 USB-A

screw-lock connectors for standard USB3.2 Gen 1 and legacy

USB2.0/1.1 devices.

Note 1: The last USB port (Port 7) of this hub does NOT

support USB2.0/1.1 devices because it is used to

communicate with the managing utilities. However, it still

supports USB3.2 Gen 1 devices.

2. USB-B Upstream Facing Port Connector: The Type-B screw-lock

connector from upstream USB3.2 Gen 1 port. It is connected from

host or another USB3.2 hub’s downstream facing port.

3. Power LED: Turns on indicates the hub was powered.

4. Port State Indicator LEDs: Each port has a LED next to it. When the

LED is on, the USB device is enabled (connected). If the LED is off, the

USB device is disabled (disconnected).

5. Self Power Input Connectors: The DC-Jack or 2-pin (one pin is for

the positive voltage and the other pin is GND) screw-lock terminal

2. Connector Layout

Power LED

USB-A Downstream Ports

Upstream Port

Connector

Screw-Lock

Terminal

Blocks

Port On/Off State LED Indicators

(this is Port 1)

DC-Jack

7-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit

blocks is used to connect wide range power source to self-power the

hub, the voltage can be in the range from +7V to 48V DC.

1. Use static electricity discharge precautions.

Remove possible static discharge potential from any objects that the

hub may come in contact with before installation. This can be

accomplished by touching a bare metal chassis rail after you have

turned off the power.

2. Apply DC power (range from +7V to 48V) to the 2-pin Screw-Lock

Terminal Block Connector.

Warning!!

Please make sure the polarity of the input power should

correctly match with the marking next to the terminal block

pins

⚫The terminal blocks’ Push-In mechanism allows you to push the

wire directly into the contact hole and latched by its internal latch

spring automatically.

⚫To remove the wire, you need a tool (such as a small flathead

screwdriver) to release the internal latch spring then remove the

wire as the following picture. If the wire is too soft to be inserted

into the contact hole, you need to release the latch string with

above tool, insert the wire then release the latch spring to latch

the wire.

3. Hardware Installation

7-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit

3. Connecting USB Host cable: The host cable can be a standard

B-to-A or B-to-C USB3.2 Gen 1 cable (depends on the host port’s

connector type). Please connect the type-A (or Type-C) end

connector of the cable to your USB host port, then connect the

type-B end connector to this hub. Since the USB hub is

plug-and-play, you don’t have to turn off your host computer when

installing the hub.

4. Connect the USB devices to the downstream ports of this hub.

5. Install the USB Hub Administrator Utilities as described in the

following chapter

4. USB Hub Administrator Utilities Installation

7-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit

The Hub supports managing utilities called USB Hub Administrator for

major recent Windows (XP and above) and Linux:

The above folders include the software for different platforms. If

you are installing it on Windows, please find the executable setup

program in Windows folder, double-click it:

1. Please follow the on-screen instructions of the setup

program to complete the installation. After installed, it will

launch the utility automatically:

7-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit

⚫Click Auto Search to find all Managed USB Hubs

⚫Click the item on the list to select the Hub to control

⚫Click on the numeric (indicate the Port number) button to

turn On/Off the USB port

⚫You can save the current port states by clicking the Save

Port States button

2. To use the console utility CUSBC to control the USB devices,

please run Command Prompt as follows:

7-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit

To see all CUSBC commands, type:

CUSBC /?

To query all Hubs connected:

CUSBC /Q

To perform a factory reset:

1. Verify that your hub’s Power LED is off.

5. Restore to Factory Settings

7-Port Managed USB3.2 Gen 1 Metal Hub with DIN RAIL Mounting Kit

2. On the side of your hub, locate the hole of the Restore Factory

Settings button:

3. Use a paper clip or similar object to press and hold the Restore

Factory Settings button, while still holding the button power on the

hub.

4. Release the Restore Factory Settings button.

5. Your hub resets to its factory default settings:

⚫All ports are On

⚫The password: pass

Restore Factory

Settings button

7-Port USB3.2 Gen 1 Managed Metal Hub with DIN RAIL Mounting Kit

Operating temp.: 0 to 55C (32 to 131F)

Operating humidity: 5 to 95% RH

Dimensions (LxWxH): 163 x 55.0x 31.2 mm

(6.41 x 2.16 x 1.22 in)

6. Environmental Specifications

Indice

Altri manuali CoolGear Interruttore

CoolGear

CoolGear USBG-7DU2S Manuale utente

CoolGear

CoolGear CG-10U2AML Manuale utente

CoolGear

CoolGear USB3- 16U1 Manuale utente

CoolGear

CoolGear CG-7PU31HB Manuale utente

CoolGear

CoolGear CG-U31iS4PH Manuale utente

CoolGear

CoolGear USBG3-3X4M Manuale utente

CoolGear

CoolGear USBG-7DU2i Manuale utente

CoolGear

CoolGear USBG-7U3ML Manuale utente

CoolGear

CoolGear CG-G17PHHT Manuale utente

CoolGear

CoolGear CG-16PU31H Manuale utente

CoolGear

CoolGear USBG-12U2ML Manuale utente

CoolGear

CoolGear USBG-4U3ML Manuale utente

CoolGear

CoolGear CG-4P31CHUB Manuale utente

CoolGear

CoolGear USBG-4PUSB2-MH Manuale utente

CoolGear

CoolGear USBG-10XU1 Manuale utente

CoolGear

CoolGear USBG-4U2ML Manuale utente

CoolGear

CoolGear USBG-4U2ML Manuale utente

CoolGear

CoolGear USBG-4SU2MLA Manuale utente

CoolGear

CoolGear CG-7PU313C Manuale utente

CoolGear

CoolGear USBBG-12U2ML Manuale utente

CoolGear

CoolGear USB3-16U1 Manuale utente

CoolGear

CoolGear USBG-4U3MLR2 Manuale utente

CoolGear

CoolGear CG-10PU3MGD Manuale utente

CoolGear

CoolGear USBG-3X4M Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente