Coolzone CZ55552 Manuale utente
INSTALLATION AND OPERATING INSTRUCTIONS
Stainless Steel
Built-in 4 Function Fan Oven
and Gas Hob pack
CZ55552
These products may differ from the ones illustrated but the installation and operation procedure remains the same
CZ55524
Contents
Introduction 3
Unpacking 3
Before installation 3
Combined or Separate installation 4
Location 4
Housing dimensions 5
Electricity supplies 6
Hob cut-out 7
Fitting the Hob 8
Hob gas supply connection 9
Hob electrical connection 9
Fitting the Oven 10
Oven and hob preparation 10
Safety notes 11
Using the hob 12
Fire safety 12
Using the oven 13
Using the grill 14
Care of the hob 15
Cleaning the hob 15
Cleaning the oven 15
Cleaning the glass oven door 16
Changing the oven lamp 16
Mains lead replacement 17
Plug replacement 17
For best cooking results 18
Troubleshooting guide 19
Customer Helpline Back page
Specification Back page
Safe product disposal Back page
3
Introduction
This quality oven and hob have been designed to provide trouble-free service provided they are installed
and maintained correctly. Both units are for domestic use only.
Please read these instructions carefully before installing or using your appliances. It is advisable to keep
your purchase and installation receipts with these instructions in a safe place for future reference. Included
is some important safety information, guidelines and recommendations to enable you to safely use your
oven and hob.
These appliances have been tested and certified to meet all applicable UK electrical and gas safety
standards.
The hob must be installed, connected and repaired in accordance with current installation
regulations by a CORGI registered gas fitter or qualified service engineer.
The oven must only be repaired by qualified electricians or service personnel.
If these appliances are not installed and repaired properly you could be putting yourself and others in
danger. It will also invalidate the guarantee.
If you have any questions or need assistance please telephone the Helpline on 0844 871 0011.
When contacting the Helpline please have model numbers to hand.The oven’s model number is shown on
the data label which is visible by opening the door. The hob’s number is shown on the data label on the
underside of the casing.
Unpacking
Carefully remove all the packaging and lift out the appliances and accessories, watching out for sharp
edges.
Remove any tape or packing material used for transit, including any material inside the oven.
Check the appliances for any damage. If either unit has been damaged do not use it and contact the
retailer from whom the appliance was bought.
Retain the packaging until the units have been installed, removing it from the area of installation and
keeping it out of the reach of children.
Dispose of all the packaging in accordance with your local authority guidelines as well as any old appliance
that is being replaced – see safe oven disposal section.
Before installation
Before any installation work can be carried out a number of requirements must be met.
Make sure that you or your installer are familiar with all the relevant building and fire regulation
requirements before choosing the location of your appliance.
This appliance must be installed in accordance with the instructions to validate the guarantee.
Refer to the “Location” section for minimum clearances and safe placement of your appliances
4
Combined or Separate Installation
Figure 2 - separate installation
There are two installation options for this oven and hob pack:
1. Oven and hob combined in a single housing unit under a worktop, as shown in Figure 1.
2. Oven and hob installed separately into individual housing units as shown in Figure 2.
Before deciding on the position of your appliances, please read the ‘location’ and ‘housing dimensions’
sections that follow..
Figure 1 - combined installation
Location
Avoid installing the oven or hob next to a fridge, freezer or boiler.
It is best if the hob is surrounded by work surface, giving safe space to rest a hot pan and space to turn
handles so that they do not protrude into the walkway or become too hot over a neighbouring hotplate.
Hob clearance space
Certain minimum clearances must be allowed for when
planning the unit’s location (Figure 3):
Beneath the work surface, allow the required clearance for
appliances or units to be installed below.
There should be an open space above the hob to allow
kitchen odours to disperse. A cooker hood may be
installed to either absorb or extract the odours.The
distance between the hob and the hood must not be less
than 650mm (Figure 3).
The distance between the hob and the back edge of the
worktop should be no less than 50mm (Figure 3).
Leave adequate clearance between the hob and adjacent
cupboards (no less than 150mm.)
To ensure that the hob is properly supported, the distance
between the hob cutout and the worktop end should be no
less than 60mm (Figure 3).
Ensure a gap of not less than 400mm between the hob
surface and overhanging cupboards.
650mm
MIN
400mm
MIN
60mm MIN
50mm
150mm MIN
Figure 3 - minimum clearances (hob)
5
Safety Requirements
Ensure that the surrounding material is heat resistant and non-combustible.
The electricity supply must be routed near to the installation (see page 6).
There must not be any plugs, wires or sockets in the wall directly above or behind the hob.
Housing dimensions
Before starting the installation process, it is important to check that the appliances will fit into the units they
will be housed in. These dimensions apply equally to combined or separate installations.
Hob
The hob must be installed into a work surface, fitted with an opening cut into the surface so that the top
plate sits flush with the surface. It can be fitted above the oven, or separately, but in either case It is best
positioned directly above a 600mm wide fitted kitchen cabinet (Figure 4).
Oven
The oven can be installed into a housing unit of the correct dimensions, either below a worktop, or into a
separate floor standing unit. (Figure 5).
Location continued
Figure 5 - oven housing dimensions
585mm
HEIGHT
MIN
565mm ±2
WIDTH
560mm
DEPTH
Figure 4 - hob housing dimensions
600mm
600mm MIN
HOB
POSITION
HOB
POSITION
6
Electricity supplies
Once satisfactory locations have been established, the electrical supplies to the appliances must be
arranged.
Hob only
A 3-pin plug socket with an earth contact, if one does not already exist, should be installed beneath the
work surface and near to the hob location, where it is easily accessible.
The 3-pin socket should be close enough so that the appliance can be easily plugged in without stretching
the mains supply cable.
The mains supply cable must be routed away from hot surfaces.
Oven only
A 3-pin plug socket with an earth contact, if one does not already exist, should be installed on the wall
behind the oven, and a suitably rated isolator switch should be installed to one side of the unit, above the
work surface or at similar height, for easy access in case of emergency (Figure 7).
This installation must be carried out in accordance with current I.E.E.Wiring Regulations and Building
Regulations (Part P).
If in any doubt consult a qualified electrician
The mains voltage must correspond exactly to that which is specified on the data plates.
ISOLATOR
SWITCH
Figure 6 - electricity supply (hob / combined) Figure 7 - electricity supply (oven only)
ISOLATOR
SWITCH
3-PIN
SOCKET
TWIN
3-PIN
SOCKET
7
Hob cut-out
PLEASE NOTE: If the hob and oven are to be installed into a single housing unit (combined
installation), the hob must be fully installed before the oven can be installed.
A cut-out for the hob can be made onto the work surface as follows:
1. Cover the approximate area for the cut-out with masking tape.
2. Position the unit face down on the surface, ensuring that the top plate is exactly centred above the
600mm kitchen cabinet supporting the worktop, and that you have the correct clearance spaces around
the hob.
3. Draw round the hob to mark the space that will be taken up by the top plate on the work surface.
4. Lift the unit away to a safe distance, and check that the outline produced corresponds with the hob
dimensions (585 x 500) in Figure 8.
5. Mark the cut-out (565 x 480 as in Figure 8) onto the masked work surface.The cut-out line should be in
a central position so that there is an even space of 10mm between the cut-out shape and the hob
outline, all the way round (Figure 9).
6. Ensure that no pipes, hoses or wires are present as obstructions below the worktop, then cut the
opening into your work surface exactly where you have marked the cut-out shape (Figure 9).
7. Remove the tape and ensure the area is clean and free of dust and debris.
8. Carefully lift the hob and place it into the cut-out opening to check for a good fit.
Do not clamp the unit into place yet as arrangements must be made to connect the unit to its
electricity supply.
Figure 8 - cut-out dimensions Figure 9 - marking the cut-out
10mm
HOB
OUTLINE
CUT-OUT
SHAPE
585mm
500mm
480mm
565mm
8
Fitting the hob
Once the hob has been connected to its electricity supply, it can be fitted into position as follows:
1. Place the hob upside down on an adjoining surface.
2. Fit the clips onto the hob by sliding the notched end into the slot and loosely screwing the screw into
the screw-hole (Figure 10).Turn the clips round so that they are in line with the hob (Figure 11).
3. Make sure that the underside edge of the hob is clean and dry.
4. Stick the foam sealing strip around the underside of the hob, 5mm in from the edge, removing the
adhesive backing as you go (Figure 11). When the sealant has been stuck round all four sides and
meets up with itself, trim off any excess sealing strip, leaving a neat join.
5. You may wish to add a thin bead of clear silicone sealant around the underside edge of the hob.
6. Turn the hob over and place it in centralised position in the cut-out hole, making sure that the electricity
supply cable is clear of the base of the hob and any other possible heat source.
7. Turn the clips, making sure that the clips grip the worktop, and then tighten the screws (Figure 12).
8. If necessary, finish the bead of sealant with a suitable tool while it is still workable.
Figure 10 - preparing the clips Figure 11 - applying sealing strip
Figure 12 - fixing to worktop
SCREW
SLOT CLIP
SCREW-HOLE
FOAM
SEALING
STRIP
CLIPS
CLIP
SCREWS
CLIP
9
Hob electrical connection
Once the gas supply has been connected, plug the hob into the 3-pin socket, and switch the socket ON.
Hob gas supply connection
PLEASE NOTE: Connection of the gas supply, adjustment, cleaning and tap servicing should ONLY
be carried out by a CORGI registered gas fitter or qualified service engineer, in accordance with the
latest regulations.
There are two installation options:
Connection to natural gas supply
The hob comes ready for connection to a piped supply of natural gas, and should only be connected by a
CORGI registered gas fitter or qualified service personnel, in accordance with the latest regulations.
Before connecting the hob to the gas supply system, ensure that the appliance is compatible with the local
distribution conditions (nature of the gas and gas pressure). In the event of incompatibility, consult a CORGI
registered installer to make the necessary adaptations or adjustments.
Connection to an LPG cylinder
Alternatively, the hob can be connected to an LPG cylinder. In this case, the LPG injector jets (supplied)
should be fitted by the qualified service engineer. Use a rubber hose with a safety certificate to connect the
applicance to the LPG cylinder.
Every time the hob has been connected to an LPG cylinder, check the cylinder valve for soundness and the
connection of the regulator to the cylinder and also its operation.
WARNING: Under no circumstances should the gas tightness be checked by means of a naked
flame (e.g with a match or candle) as there is a danger of explosion.
WARNING: Before starting any adjustments or changing the injectors, disconnect the appliance
from gas and mains electricity supply.
10
Fitting the oven
Before installing the oven in its housing, insert the mains plug into the mains outlet socket. Avoid trapping
the mains cable between the appliance and the housing and ensure it is routed away from hot surfaces.
Place the oven into the housing unit and adjust its position until it is level, making sure it aligns with any
adjacent units, drawers, and cupboard doors (Figure 13).
When correctly positioned, drill the unit and secure the appliance in place with two fixing screws
(Figure 14).
Figure 13 - centralising the oven
SCREWS
Figure 14 - installing the oven
Oven and hob preparation
1. Remove the remnants of any stickers, glue and adhesive tape from the surfaces and burners of the hob
and oven, with warm water and washing-up liquid.
2. When the appliances are cool, wipe them with a soft dry cloth.
3. Ensure that all elements of the hob burners are positioned correctly.
PLEASE NOTE:When using for the first time the oven may smell for a short time while burning off
dust and manufacturing residues from the heating elements.This is normal and does not indicate a
fault with the oven.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Coolzone Elettrodomestico da cucina
