CTA PAD-ADMA Manuale utente
888-733-4448
CONTENTS:
INSTRUCTIONS:
2A. When the C-Clamp is securely
attached to a surface, use the
provided security tool, attach to
security component, and rotate
closewise to put the C-Clamp in an
‘locked’ state. To loosen, rotate
counterclockwise with the security
tool.
Remove arm from the base
clamp mount. Repeat steps
in reverse to re-install
connection
2B. Align the (2) dimples on the underneath of the
security tool into the two holes on the security
component on the clamp as shown above
2C. Rotate counter-clockwise to
loosen and place the clamp in an
‘unlocked’ state. Continue rotating
until there is enough slack to rotate
the knob.Turn it clockwise to tighten
and place the clamp in a ‘locked’
state.
2
BASE CLAMP SECURITY SETUP
BASE MOUNT INSTALLATION ARM TO BASE CLAMP
ADJUSTMENTS
If you need to remove the arm
from the base clamp, take the
provided larger allen key tool,
rotate, and loosen connection
12
3
Find the included base
pad (shown above) and
peel off the backing. Align
to the underneath of the
C-Clamp and apply pad. While the clamp is in unlocked mode, rotate the
knob at the bottom (as shown above) to loosen
or securely tighten to the table top.
ALIGNING SECURITY TOOL WITH SECURITY COMPONENT
Unlock by moving the
red lever over to
unlock position
Lock by pressing claw
arms back in around
device, then moving
lever into lock position.
Unlock by making sure
key is inserted and
then moving the red
lever over to unlock
Lock by pressing claw
arms back in around
device, then moving
lever into lock position,
then removing the key
888-733-4448
When charging your device, find
the port, then route your cable
through the opening on the ends of
the holder arms.
When routing cables for the from
device to the power source, use
provided clips as shown to keep
the cables organized and tight to
the arms to avoid any slack.
Each hinge of the product can be
adjusted easily with the provided
smaller allen key tool. Loosen to adjust
and securely tighten after preferred
position is set.
When all hinges and joints are tightened, do not attempt to
forcibly flex the angles or positioning without loosening. Any
attempt to do so will possibly have an effect on product integrity
and CTA and manufacturer will not be responsible for any
mishandling.
TABLET INSTALLATION
JOINT ADJUSTMENTS CHARGING
SETUP
CABLE
ROUTING
4
567
Altri manuali CTA Rack e supporto
CTA
CTA PAD-MSPC10 Series Manuale utente
CTA
CTA PAD-CHAIRPB Manuale utente
CTA
CTA PAD-TPADM Manuale utente
CTA
CTA PAD-TAM Manuale utente
CTA
CTA PAD-SHFS Manuale utente
CTA
CTA PAD-VADMWE Manuale utente
CTA
CTA PAD-2VDMB Manuale utente
CTA
CTA PAD-SWM Manuale utente
CTA
CTA PAD-PARAFP Manuale utente
CTA
CTA PAD-ASKM6 Manuale utente
CTA
CTA ADD-FS2VDMB Manuale utente
CTA
CTA PAD-HSKSBAE Manuale utente
CTA
CTA PAD-MFSV Manuale utente
CTA
CTA PAD-SWM Manuale utente
CTA
CTA PAD-PARAFPE Manuale utente
CTA
CTA PAD-SSMA Manuale utente
CTA
CTA PAD-UGT Manuale utente
CTA
CTA PAD-WDM Manuale utente
CTA
CTA PAD-PARAF1 Manuale utente
CTA
CTA ADD-USGTWP Manuale utente
