Danfoss DEVIreg 130 Manuale utente
www.DEVI.com
Installation Guide
DEVIreg™ 130
Electronic Thermostat
DEVIreg™ 130
Installation Guide2
DEVIreg™ 130
Installation Guide 3
1 Introduction
DEVIreg™ 130 is an electronic thermostat to be installed
directly on the wall. It is provided with a floor sensor to
measure and control the desired floor temperature.
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 1 to 5 (each step corresponds
to approximately 9 °C). Furthermore, the thermostat has an
LED indicator showing standby periods (green light) and
heating periods (red light).
More information on this product can also be found at:
devireg.devi.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specifications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . 6
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Temperature Settings . . . . . . . . . . . . . . 10
4 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Disposal Instruction . . . . . . . . . . . . . . . . . . 14
DEVIreg™ 130
Installation Guide4
1.1 Technical Specifications
Operation voltage 220-240V~, 50Hz
Power consumption Max 5W
Relay:
Resistive load
Inductive load
Max 16A / 3680W @ 230V
cos φ= 0.3 max 1A
Sensing units NTC 15 kOhm at 25°C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0,2 °C
Ambient temperature 0 to +30 °C
Frost protection temperature 5 °C -
Temperature range ( ) 5–45 °C
Cable specification max 1 x 4 mm² or 2 x 2,5 mm²
Ball pressure temperature 75 °C
Pollution degree Degree 2 (domestic use)
Type 1C
Storage temperature -20 to +65 °C
IP class 30
Protection class Class II -
DEVIreg™ 130
Installation Guide 5
Dimensions 82 x 82 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
IMPORTANT: When the thermostat is used to control a
floor heating element in connection with a wooden floor or
similar material, always use a floor sensor and never set the
maximum floor temperature to more than 35 °C.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
DEVIreg™ 130
Installation Guide6
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
Place the thermostat at a suitable height on
the wall (typically 80-170cm.).
In wet rooms, place the thermostat according
to local regulation on IP classes.
Do not place the thermostat on the inner side
of an exterior wall.
DEVIreg™ 130
Installation Guide 7
• Place the floor sensor in a conduit in an
appropriate place where it is not exposed
to sunlight or draft from door openings.
• Equally distant and >2cm from two heating
cables.
• The conduit should be flush with the
floor surface - countersink the conduit if
necessary.
• Route the conduit to the connection box.
• The bending radius of the conduit must be
min 50mm.
DEVIreg™ 130
Installation Guide8
Follow the steps below to mount the thermostat:
1. Open the thermostat:
• Lift off the button using a small screwdriver.
• Loosen the screw which holds the front.
• Push down the release tab at the top of the
thermostat using a flat object while slowly pulling
off the front cover.
DEVIreg™ 130
Installation Guide 9
2. Fasten the thermostat directly to the wall by driving
the screws through the holes in each side of the
thermostat.
= Screw holes for fastening the thermostat.
3. Connect the thermostat according to the connection
diagram.
IP30
0T30
D130
NTC
1234
Sensor
Max.Load
16 (1) A
Mains
220-240V~
N
LOAD
L
LOAD
NL
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: Always install the floor sensor in a conduit in
the floor.
DEVIreg™ 130
Installation Guide10
4. Install the front cover and button in the reverse order
of disassembly.
5. Turn on the power supply.
3 Settings
3.1 Temperature Settings
How to change the minimum and maximum floor
temperatures
1. Lift off the adjustment
button using a thin
screwdriver.
2. Move the pins to the
desired positions.
(and ).
3. Put the adjustment button
back in place.
Please be aware of the following:
• The floor temperature is measured where the sensor
is placed.
• The temperature of the bottom of a wooden floor can
be up to 10 degrees higher than the top.
• Floor manufactures often specify the max
temperature on the top surface of the floor (usually
27-28 °C).
Indice
Altri manuali Danfoss Termostato
Danfoss
Danfoss 060L2150 Manuale utente
Danfoss
Danfoss TP75 Manuale operativo
Danfoss
Danfoss Eco Manuale utente
Danfoss
Danfoss 088L5133 Manuale utente
Danfoss
Danfoss DEVIreg 532 Manuale utente
Danfoss
Danfoss FP735Si Manuale utente
Danfoss
Danfoss HCS6101-3 Istruzioni utente
Danfoss
Danfoss ECtemp 531 Manuale utente
Danfoss
Danfoss FH-WT Manuale utente
Danfoss
Danfoss ORT-01 Manuale utente
Danfoss
Danfoss CF-RF Manuale utente
Danfoss
Danfoss ECtemp 330 Manuale utente
Danfoss
Danfoss DEVI DEVIreg Opti Manuale utente
Danfoss
Danfoss HC75-1 Manuale operativo
Danfoss
Danfoss EFET 130 Manuale utente
Danfoss
Danfoss TP7000M Manuale utente
Danfoss
Danfoss DEVIreg 330 Manuale utente
Danfoss
Danfoss ECtemp 531 Manuale utente
Danfoss
Danfoss TP4000 Range Manuale utente
Danfoss
Danfoss SH-E01 Manuale utente
