Dell PowerEdge R910 Manuale tecnico

Dell™ PowerEdge™ R910

Systems

Information Update

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Intel

is a registered trademark of Intel Corporation in the U.S. and other countries; Microsoft, Windows

Server, and Windows are either trademarks or registered trademarks of Microsoft Corporation in the

United States and/or other countries. Broadcom is a registered trademark of Broadcom Corporation

and/or its subsidiaries in the United States and certain other countries. Red Hat and Red Hat Enterprise

Linux are registered trademarks of Red Hat, Inc. in the United States and other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

April 2010 Rev. A00

Information Update 3

Microsoft Updates

The following issues are documented on the Microsoft®Help and Support

website at support.microsoft.com:

• Systems running Microsoft Windows Server

2003 or Windows

Server 2008 cannot be set to hibernation if they have more than 4 GB of

memory installed. For more information about enabling hibernation on

systems with more than 4 GB of memory, see the knowledge base article

KB888575 at

microsoft.com

• Microsoft Windows Server 2008 R2 cannot be installed or run on systems

with 1 TB of system memory and cannot resume from hibernation mode.

This issue may occur either in Unified Extensible Firmware Interface

(UEFI) or in legacy BIOS modes. For more information, see the knowledge

base article KB980598

microsoft.com

• Systems running Microsoft Windows Server 2008 do not support iSCSI

boot when they have an SD card installed in the internal SD module. In

addition, iSCSI boot does not work when an external USB storage device is

plugged into the system. For more information, see the knowledge base

article KB968410 at

microsoft.com

Flash Memory

The VFlash media provided by Dell is not partitioned to support the iDRAC6

Enterprise virtual flash feature. When you use the virtual flash feature for the

first time, you are prompted to format the media using the iDRAC GUI.

Red Hat Enterprise Linux 5.4 Address Limitation

With 1 TB (When Memory RAS Mode is Not Used)

Red Hat®Enterprise Linux®5.4 has an address limitation with 1 TB of

system memory. To install Red Hat Enterprise Linux 5.4, use the mem=

1024M boot time switch. The system does not boot to the operating system

unless a boot time switch mem=1024G is used. For more information, see the

knowledge base article at kbase.redhat.com/faq/docs/DOC-25412.

4Information Update

Microsoft Windows Server 2003 R2 SP2 (x64)

Edition With SP2 Limitation With 1 TB System

Memory (When Memory RAS Mode is Not Used)

The system does not boot to the operating system with 1 TB of system

memory. To resolve this issue, set the memory RAS mode to sparing or mirror.

After installing the operating system, add a boot time switch mem=1046528

or /burnmemory=2048 in the boot.ini file before disabling the RAS mode

for subsequent boots.

MAC Address Labels

For security reasons, the embedded NIC and iDRAC6 Enterprise MAC

address labels provided with your system cannot be affixed after they have

been removed.

NOTE: The labels are located on the system identification panel on the front of the

system.

System Limitations With an Optional 10 Gb I/O

Riser

The 10 Gb I/O riser provides two 10 Gb SFP+ ports using a Broadcom®

57711 controller in addition to two 1 GbE ports. The following are the

limitations with the 10 Gb I/O riser:

• To ensure system power redundancy, the 10 Gb I/O riser requires all four

power supplies to be connected to the AC power source. The system power

becomes non-redundant if one of the power supplies is removed.

CAUTION: A power supply failure or removal of another power supply after the

system power becomes non-redundant can lead to a system failure and results in

loss of data.

• Wake On LAN (WOL) is not supported on the 10 Gb

SFP+

ports due to

Broadcom 57711 design limitations. However, WOL is supported on the

two 1 GbE ports available on the riser.

Information Update 5

System Limitations With an Optional PCIe Riser

The PCIe riser expands the number of PCIe expansion slots available in the

system to 10. Due to the limitation of 64 KB I/O address space on the Intel®

IA32 architecture and the I/O granularity of 4 KB set by the PCI bridge

specification, you can exceed the I/O resources if you populate the slots with

adapters which require more than 4 KB of I/O address space. The system does

not complete POST if 64 KB I/O address space is exceeded. For more

information on supported adapters, see the Dell™ PowerEdge™ R910

Hardware Owner's Manual at support.dell.com/manuals.

Dell Update Package Information

During the Dell Update Package (DUP) installation process, you may see

messages related to the following:

• Request for system reboot before the DUP installation is complete

• Windows hardware detection

• Windows hardware configuration problem

• Re-enumeration of VFlash and momentary drive letter changes in

Windows

CAUTION: Ensure that you do not perform write operations during DUP

installation on VFlash.

It is recommended that you disable the OS Watchdog Timer in the system

BIOS when running the BIOS DUP. The system may reboot in the middle of

an update and results in corrupted flash if:

• The

OS Watchdog Timer

in the system BIOS is enabled

• The timer expires (if set too short)

NIC Teaming

The system has Broadcom embedded NICs that can be teamed with other

vendors such as Intel. It is recommended that you use Broadcom teaming

driver.

6Information Update

Dell PERC H800 Storage Adapter Slot Limitation

(With PERC H700i as the Internal Storage

Controller)

The system supports up to two PERC H800 adapters. There is no slot

limitation when only one H800 adapter is installed. However, when you install

two H800 adapters in a system with a PERC H700i internal storage adapter,

one of the H800 adapters must be installed in slot 7 (x16 Gen 2 slot). If you

run embedded system diagnostics without an H800 adapter installed in slot 7,

a software error occurs.

Under the same condition, if you enable Collect System Inventory on Restart

(CSIOR), you may not be able to boot to the operating system. You can

enable/disable CSIOR through the iDRAC Configuration Utility by pressing

<Ctrl><E> during boot up. For more information, see the iDRAC User’s

Guide at support.dell.com/manuals.

Dell Lifecycle Controller System Services

Limitations

Table 1. Lifecycle Controller System Services Issues

Cause Solution

SAS6/iR or PERC H200 has virtual disks

in an inactive or non-optimal state.

Make the virtual disks active before

booting to Lifecycle Controller.

PERC H200 or 6 Gbps SAS HBA are

configured with two virtual disks.

This is a known issue. Do not create

multiple virtual disks using either PERC

H200 or 6 Gbps SAS HBA.

Information Update 7

Hardware Owner’s Manual Updates

BIOS Setup Options Default Settings Update

Power Supply Redundancy Mode (With a 10 Gb I/O Card)

For a redundant system configuration with a 10 Gb I/O card and four power

supplies, the redundancy mode is 2+1.

System Memory

Follow the procedure given below for installing and removing the memory

modules if your system has a memory riser as shown in

Figure 1

Installing Memory Modules

WARNING: The memory modules are hot to the touch for some time after the

system has been powered down. Allow time for the memory modules to cool

before handling them. Handle the memory modules by the card edges and avoid

touching the components on the memory module.

CAUTION: Many repairs may only be done by a certified service technician. You

should only perform troubleshooting and simple repairs as authorized in your

product documentation, or as directed by the online or telephone service and

support team. Damage due to servicing that is not authorized by Dell is not covered

by your warranty. Read and follow the safety instructions that came with the

product.

Turn off the system, including any attached peripherals, and disconnect

the system from the electrical outlet.

Open the system. See "Opening the System" in the

Hardware Owner’s

Manual

Table 2. Default Settings for BIOS Setup Options

Screen Option Default Option

Memory Settings System Memory Testing Disabled

Power Management Power Management Active Power Controller

Integrated Devices SR-IOV Global Enable Disabled

SATA Settings Embedded SATA ATA Mode

8Information Update

Remove the memory risers. See "Removing a Memory Riser" in the

Hardware Owner’s Manual

Press the two release tabs until the memory module cover is unlatched and

lift it in the direction of the arrow. See Figure 1.

Press the ejectors on the memory module socket down and out, as shown

in Figure 3-9 in the

Hardware Owner’s Manual

Align the memory module's edge connector with the alignment key of the

memory module socket, and insert the memory module in the socket.

NOTE: The memory module socket has an alignment key that allows you to

install the memory module in the socket in only one way.

Press down on the memory module with your thumbs to lock the memory

module into the socket.

When the memory module is properly seated in the socket, the ejectors on

the memory module socket align with the ejectors on the other sockets

that have memory modules installed.

Repeat step 5 through step 7 of this procedure to install the remaining

memory modules. See Table 3-1 and Table 3-2 in the

Hardware Owner’s

Manual

Press the four tabs and close the memory module cover. See Figure 2.

Install the memory risers. See "Installing a Memory Riser" in the

Hardware

Owner’s Manual

Close the system. See "Closing the System" in the

Hardware Owner’s

Manual

Reconnect the system to its electrical outlet and turn the system on,

including any attached peripherals.

Press <F2> to enter the System Setup program, and check the

System

Memory

setting on the main

System Setup

screen.

The system should have already changed the value to reflect the newly

installed memory.

If the value is incorrect, one or more of the memory modules may not be

installed properly. Repeat step 2 through step 13 of this procedure to

ensure that the memory modules are firmly seated in their sockets.

Information Update 9

Run the system memory test in the system diagnostics. See "Running the

Embedded System Diagnostics" in the

Hardware Owner’s Manual

Figure 1. Installing and Removing a Memory Module

1release tabs (2) 2handle

3memory riser 4release button

5card guide 6memory-riser connector

10 Information Update

Removing Memory Modules

WARNING: The memory modules are hot to the touch for some time after the

system has been powered down. Allow time for the memory modules to cool

before handling them. Handle the memory modules by the card edges and avoid

touching the components on the memory module.

CAUTION: Many repairs may only be done by a certified service technician.

You should only perform troubleshooting and simple repairs as authorized in

your product documentation, or as directed by the online or telephone service

and support team. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow the safety instructions that came

with the product.

CAUTION: To ensure proper system cooling, memory-module blanks must be

installed in any memory socket that is not occupied. Remove memory-module

blanks only if you intend to install memory modules in those sockets.

Turn off the system, including any attached peripherals, and disconnect

the system from the electrical outlet.

Open the system. See "Opening the System" in the

Hardware Owner’s

Manual

Remove the memory risers. See "Removing a Memory Riser" in the

Hardware Owner’s Manual

Press the tabs in the direction of the arrows and lift the memory

module cover. See Figure 2.

CAUTION: Handle each memory module only on either card edge, making sure

not to touch the middle of the memory module.

Press down and out on the ejectors on each end of the socket until the

memory module pops out of the socket.

Press the four tabs and close the memory module cover. See Figure 2.

Altri manuali per PowerEdge R910

Indice

Lingue:

Altri manuali Dell Server

Dell

Dell Wyse 5070 Extended Manuale utente

Dell

Dell PowerEdge C6105 Manuale operativo

Dell

Dell PowerEdge R430 Manuale utente

Dell

Dell PowerEdge R210 Manuale tecnico

Dell

Dell POWEREDGE DL385 Manuale utente

Dell

Dell PowerEdge SC430 Manuale utente

Dell

Dell PowerEdge R310 Manuale utente

Dell

Dell PowerEdge M620 Manuale utente

Dell

Dell PowerEdge FC630 Manuale utente

Dell

Dell PowerEdge R900 Manuale tecnico

Dell

Dell Wyse C10LE Manuale di servizio

Dell

Dell PowerEdge R310 Manuale utente

Dell

Dell EMC PowerEdge R7515 Manuale

Dell

Dell DR4000 Restore Manager Manuale di servizio

Dell

Dell POWEREDGE 1900 Manuale utente

Dell

Dell PowerEdgeFC430 Manuale utente

Dell

Dell PowerEdge R730xd Manuale utente

Dell

Dell PowerEdge R320 Manuale utente

Dell

Dell PowerEdge XR4520c Manuale

Dell

Dell PowerEdge C6145 Manuale utente

Dell

Dell PowerEdge C6145 Manuale utente

Dell

Dell PowerEdge 1750 Manuale

Dell

Dell poweredge VRTX Manuale utente

Dell

Dell PowerEdge 1850 Manuale

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente

Planet

Planet NAS-7410 Manuale utente

Lenovo

Lenovo ThinkSystem SR635 V3 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX900 Manuale utente

Asus

Asus RS700DA-E6 PS4 Manuale utente