DFI VC230-BT Manuale utente
1
VC230-BT Installation Guide
Package Contents
DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
www.d.com
Note:
The CD that came with the system contains an autorun screen to install drivers, utilities,
and software applications required to enhance the performance of the system and a user's
manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will
appear. If after inserting the CD, “Autorun” did not automatically start, please go directly to
the root directory of the CD and double-click “Setup”. Please install all required drivers.
•
1 VC230-BT system unit
• 6
Mounting screws for Mini PCIe module
•
1 Quick Installation Guide
•
1 Disk includes:
- Drivers / Manual
2
Panel
Rear View
COM 3
(RS232/RS422/RS485)
USB 2.0
LAN 2
VGA
LAN 1
Antenna
hole
Front View
HDMI
USB 3.0
Antenna
hole
COM 2
(RS232/RS422/RS485)
COM 4/ 8-bit DIO
CANbus*
Reset
Power button
(Green LED)
Status LED (Blue)
Antenna
hole
VCC/ACC/GND
(Connects to car battery)
Note:
You can choose to wire the COM 4 port to be a CANbus (Controller Area Network)
interface instead.
3
4. After removing the mounting screws, lift the bottom side of the chassis cover
to open the system. To access the Mini PCIe and the micro SD slots, revmoe the
four screws to uninstall the power board.
Removing the Chassis Cover
Please observe the following guidelines and follow the procedure to open the system.
Chassis screw
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 4 mounting screws on the bottom side of the system are used to secure
the cover to the chassis. Remove these screws and then put them in a safe
place for later use.
Mounting screw
Mounting screw
4
Installing a Mini PCIe Card
The system board is equipped with 3 Mini PCIe slots: two full-size and one half-
size slots. Here we will demonstrate the installation of a full-size Mini PCIe card
(mSATA interface) for capacity expansion.
1. Grasp the Mini PCIe card by its edges and align the notch in the connector of
the PCIe card with the notch in the connector on the system board.
2. Push the Mini PCIe card down and use the provided mounting screws to se-
cure the card on the system board.
Mounting screw
Note:
The system also has one additional full-size Mini PCIe and one half-size Mini PCIe slot
that use PCIe (PCIe/USB/3G/GPRS/CANbus signals) and LPC (PCIe/USB/LPC signals)
interface respectively.
5
Board Layout and Jumper Settings
TOP BOTTOM
SATA 1
14 SATA
Power 1
LAN 1
LAN 2
3
DDR3L
DDR3L
DDR3L
DDR3L
Mini PCIe
COM 4
1210
31
JP22 1
1
1
(JP20)
(JP18)
(JP17)
(JP21)
1 3
1210
COM 2
USB 0
USB 3.0
HDMI
Reset
Power
DC-in
USB 2
USB 7
USB 1
USB 6
COM 3
Mic-in
1
Battery
Buzzer
1
Chassis
Intrusion
1
Clear CMOS
Data (JP24)
SPI
Flash
BIOS
eMMC
(optional)
iTE
IT8528E
Mini PCIe mSATA
MicroSD
(optional)
1
System Fan
1
USB 0
Power
Select
(JP5)
1
2
5
6
(JP23)
1
1
1
(JP3)
(JP4)
1
2 10
9
COM 6
1
10
9
COM 5
1 1
USB 1-2
Power Select (JP6)
USB 5-7 Power
Select (JP7)
1
2 10
9
USB 5
(JP25)
USB 2.0
USB 2.0
(JP17)
(JP20)
COM 4/DIO Select (JP22, JP21)
Digital I/O 0-3 Output State
Digital I/O Power Select
Panel Power Select
(JP3)
(JP4)
(JP23)
Backlight Enable Power Select
Auto Power-on Select (JP25)
Dimming Mode Select
1
(JP18)
Digital I/O 4-7 Output State
1
VGA/DVI-I
4
1(JP2)
(JP2)LCD/Inverter Power Select
SATA 2.0
DDR3L
DDR3L
DDR3L
DDR3L
DDR3L
Intel Atom
E3800 Series
Intel
WGI210AT
Nuvoton
NCT6106D
ASMedia
ASM1442
Intel
WGI210AT
SMSC
USB4604
SIM Card
NXP
PTN3460
Standby
Power LED
www.d.com
USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7)
+5V_standby (default) 1-2 On
+5V 2-3 On
Clear CMOS Data JP24
Normal (default) 1-2 On
Clear CMOS Data 2-3 On
Auto Power-on Select JP25
Power-on via power button 1-2 On
Power-on via AC power (default) 2-3 On
Note:
You cannot use COM 4 and DIO at the same time.
Please adjust JP21 and JP22 together.
Digital I/O Output State JP18 (DIO 4-7)
JP20 (DIO 0-3)
GND (default) 1-2 On
+5V or +5V_standby 2-3 On
Digital I/O Power Select JP17
+5V_standby 1-2 On
+5V (default) 2-3 On
COM 4/DIO Select JP21, JP22
COM 4 (default) 1-2, 4-5
7-8, 10-11 On
DIO 2-3, 5-6
8-9, 11-12 On
6
Delay Turn-on/off Switch
The DIP switch (SW1) on the power board can be used to trun on or off the sys-
tem at a specic on/off delay time via car ignition.
SW1-2: System-on delay enable/disable
On (Default) Enable (delay time setting adjust-
able by SW1-4 and 1-5 as shown in
the table below)
Off Disable (System-on delay = 3 sec)
SW1-4 and 1-5: System-on delay time setting
4 5 Time
On On 10 sec (default)
Off On 30 sec
On Off 1 min
Off Off 5 min
SW1-3: System-off delay enable/disable
On (Default) Enable (delay time setting adjust-
able by SW1-6, 1-7 and 1-8 as
shown in the table below)
Off Disable (System-off delay = 0 sec)
SW1-6, 1-7 and 1-8: System-off delay time setting
6 7 8 Time
On On On 30 sec (default)
Off On On 1 min
On Off On 3 min
Off Off On 5 min
On On Off 10 min
Off On Off 15 min
On Off Off 30 min
Off Off Off 1 hr
www.d.com
Note:
The OS will start the shut-down procedure after the car ignition switches off.
Please make sure that system-off delay time is sufcient to allow the OS to shut
down completely.
Altri manuali per VC230-BT
1
Indice
Altri manuali DFI PC industriale
DFI
DFI KS-KH Series Manuale utente
DFI
DFI EC510 Manuale utente
DFI
DFI EC500-ADS Manuale utente
DFI
DFI EC700-BT Manuale utente
DFI
DFI EC541-HD Manuale utente
DFI
DFI DT200-CS Manuale utente
DFI
DFI EC500-CS Manuale utente
DFI
DFI EC500-ADS Manuale utente
DFI
DFI EC531-HD Manuale utente
DFI
DFI EC500-SD Manuale utente
DFI
DFI EC310 Series Manuale utente
DFI
DFI DT122-SB Manuale utente
DFI
DFI KS101P-EHL Manuale utente
DFI
DFI ES220F-CS Manuale utente
DFI
DFI EC700-QRB Manuale utente
DFI
DFI ST102-SD Manuale utente
DFI
DFI VC70B-KU Manuale utente
DFI
DFI DT122-GH Manuale utente
DFI
DFI EC700-BT Manuale utente
DFI
DFI DT122-HR Manuale utente
