Dynojet Quickshifter Manuale utente

QEM13 www.powercommander.com 2007-2013 Suzuki GSXR1000 QEM - 1

PARTS LIST

1 Quick Shifter Module

1 Installation Guide

2 Power Commander Decals

2 Dynojet Decals

1 Velcro

1 Alcohol swab

2007-2013 Suzuki GSXR1000

Installation Instructions

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com

QEM13 www.powercommander.com 2007-2013 Suzuki GSXR1000 QEM - 2

1 Remove the main seat and the passenger seat.

2 Lift the fuel tank up or remove.

3 Mount the QEM in the tail section using the supplied velcro. Make sure to

clean both surfaces with the alcohol swab before attaching.

4 Route the QEM harness down the left side of the bike.

5 Unplug the stock wiring harness from the UPPER set of injectors (Fig. B)

6 Plug the QEM harness in-line of the stock wiring harness and UPPER injectors

(Fig. C).

7 Reinstall fuel tank.

8 Plug the wiring harness from the shift sensor switch into the matching

connector of the QEM.

If using an older shift sensor that does not have this matching connector, the

wires will need to be spliced.

FIG.A

FIG.C

FIG.B

QEM13 www.powercommander.com 2007-2013 Suzuki GSXR1000 QEM - 3

4th hole from end

5th hole from end

• For the unit to function correctly the wires from

the QEM must be wired correctly to the PCV.

The BLUE wire goes to pin #4 and the GREEN

wire goes to pin #5

• To insert the wires into the PCV strip back about 10mm of the insulation from the wire. Using a paperclip (or similar) poke the hole of the

PCV to pierce the foam. It may also be helpful to tin the wire with solder for a secure connection.

• Remove the rubber seal on the back side of the PCV. Loosen the set screw of the corresponding hole and insert the wire into the PCV.

Tighten the set screw. Pull on the wire to ensure it does not pull out.

• Open the PCV control center software. Go to Power Commander Tools - Configure - Features, Enables, and Input Selections. Click on the

box to enable the Quickshifter feature. Make sure the Switch Input setting is set to Switch Input #2. Click the Configuration button for the

Quickshifter feature. You can adjust kill times per gear by going to Mode - Gear Dependent. For this to function you must have the speed

input connected to the PCV and gear position calibrated correctly (see PCV install guide).

• Your PCV firmware version needs to be at least 0.1.8.8. to use this accessory. Check by going to View - Device Info. It is recommended to

update your PCV software and firmware versions to the latest versions posted on our website. Go to Power Commander Tools - Update

Firmware. The latest firmware can be found at http://www.powercommander.com

• This QEM can only be used with a normally open circuit shift sensor/switch.

Indice

Altri manuali Dynojet Accessori per motociclette

Dynojet

Dynojet Power commander III Manuale utente

Dynojet

Dynojet Power Comander V Manuale utente

Dynojet

Dynojet Power commander GSXR750 Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Target Tune Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III 705-411 Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander 3 Manuale utente

Dynojet

Dynojet Power Commander III USB Ignition Module Manuale utente

Dynojet

Dynojet Power Commander FC Manuale utente

Dynojet

Dynojet POWER COMMANDER III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander V Ex Manuale utente

Manuali Accessori per motociclette popolari di altre marche

SRC

SRC B-TRK502-01-01-SL Manuale utente

3M Speedglas 9100 MP Manuale utente

hepco & becker

hepco & becker 6307520 00 01 Manuale utente

HOMCOM

HOMCOM AA0-077 Manuale utente

hepco & becker

hepco & becker 6307558 00 01 Manuale utente

Wunderkind Custom

Wunderkind Custom 106503-F15 Guida utente

Dräger

Dräger HPS 3500 Manuale utente

M-WAVE

M-WAVE SKI Manuale utente

Kuryakyn

Kuryakyn 6212 Manuale utente

hepco & becker

hepco & becker 6507504 00 01 Manuale utente

Tool it

Tool it PROMAX LCD 9.13G Manuale utente

Custom Dynamics

Custom Dynamics TruWrapz Manuale utente

Roof

Roof RO200 CARBON Manuale utente

Kabuto

Kabuto Japan IBUKI Manuale utente

PUIG

PUIG 5051 Manuale utente

rizoma

rizoma ZTH050 Manuale utente

Joubert

Joubert 10001711 Manuale utente

Sperian

Sperian Optrel p420 Manuale utente