Dynojet Power Comander V Manuale utente

11-008 www.powercommander.com 2010-2012 Arctic Cat 450 H1 - PCV - 1

PARTS LIST

1 Power Commander

1 USB Cable

1 Installation Guide

2 Power Commander Decals

2 Dynojet Decals

1 Posi-tap

2 Velcro strips

1 Alcohol swab

THE LATEST POWER COMMANDER

SOFTWARE AND MAP FILES CAN BE

DOWNLOADED FROM OUR WEB SITE AT:

www.powercommander.com

2010-2012 Arctic Cat 450 H1

Installation Instructions

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

THE IGNITION MUST BE TURNED

OFF BEFORE INSTALLATION!

2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com

11-008 www.powercommander.com 2010-2012 Arctic Cat 450 H1 - PCV - 2

EXPANSION PORTS 1 & 2

Optional Accessories such as

POD-300 unit or Auto-tune kit

IGNITION MODULE V

INPUT ACCESSORY GUIDE

ACCESSORY INPUTS

Wire connections:

To input wires into the PCV first remove the rubber

plug on the backside of the unit and loosen the

screw for the corresponding input. Using a 22-24

gauge wire strip about 10mm from its end. Push the

wire into the hole of the PCV until is stops and then

tighten the screw. Make sure to reinstall the rubber

plug.

NOTE: If you tin the wires with solder it will make

inserting them easier.

USB CONNECTION

Map - (Input 1 or 2) The PCV has the ability to hold

2 different base maps. You can switch on the

fly between these two base maps when you

hook up a switch to the MAP inputs. You can

use any open/close type switch. The polarity

of the wires is not important. When using the

Autotune kit one position will hold a base map

and the other position will let you activate the

learning mode. When the switch is “CLOSED”

Autotune will be activated. (Set to Switch

Input #1 by default.)

Shifter- (Input 1 or 2) These inputs are for use with the

Dynojet quickshifter. Insert the wires from the

Dynojet quickshifter into the SHIFTER inputs.

The polarity of the wires is not important. (Set

to Switch Input #2 by default.)

Speed- If your application has a speed sensor then

you can tap into the signal side of the sensor

and run a wire into this input. This will allow

you to calculate gear position in the Control

Center Software. Once gear position is setup

you can alter your map based on gear position

and setup gear dependent kill times when

using a quickshifter.

Analog- This input is for a 0-5v signal such as

engine temp, boost, etc. Once this input

is established you can alter your fuel curve

based on this input in the control center

software.

Crank- Do NOT connect anything to this port unless

instructed to do so by Dynojet. It is used to

transfer crank trigger data from one module to

another.

ACCESSORY INPUTS

CRANK

ANALOG

SPEED

INPUT 1 (Grnd)

INPUT 1

INPUT 2 (Grnd)

INPUT 2

11-008 www.powercommander.com 2010-2012 Arctic Cat 450 H1 - PCV - 3

1 Remove the seat.

2 Remove the storage cover shown in Figure A.

3 To make the injector more accessible, remove the rubber intake snorkel.

Loosen the clamp for the snorkel through the opening under the storage cover

as shown in Figure B.

4 Using the supplied Velcro, secure the PCV module under the seat at the

location shown in Figure C.

Make sure to clean both surfaces with the alcohol swab before attaching.

5 Route the PCV wiring harness under the seat frame and plastic shroud.

6 Attach the ground wire from the PCV to the negative side of the battery as

shown in Figure C.

FIG.A

FIG.C

FIG.B

Ground wire

Remove

11-008 www.powercommander.com 2010-2012 Arctic Cat 450 H1 - PCV - 4

7 Unplug the stock wiring harness from the fuel injector (Fig. D).

8 Plug the PCV wiring harness in-line of the stock wiring harness and the fuel

injector.

9 Locate the Throttle Position Sensor (TPS) on the

left hand side of the throttle body.

10 Using the supplied posi-tap, attach the GREY wire

from the PCV to the stock GREEN/BLACK wire

from the TPS.

11 Replace the storage cover and seat.

FIG.D

FIG.E

TPS

Posi-tap

Unplug

Altri manuali Dynojet Accessori per motociclette

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet POWER COMMANDER III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander 3r Manuale utente

Dynojet

Dynojet Power commander V Guida rapida

Dynojet

Dynojet POWER COMMANDER III Manuale utente

Dynojet

Dynojet Power Commander III ZX10R Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet POWER VISION 4 Manuale utente

Dynojet

Dynojet Power Commander V 23-010 Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Quickshifter Manuale utente

Dynojet

Dynojet POWER COMMANDER III Manuale utente

Dynojet

Dynojet Power Commander III USB 109-411 Manuale utente

Dynojet

Dynojet DYNOWARE RT - 224 DYNOS Manuale utente

Dynojet

Dynojet Autotune Guida all'installazione

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Manuali Accessori per motociclette popolari di altre marche

SRC

SRC B-TRK502-01-01-SL Manuale utente

3M Speedglas 9100 MP Manuale utente

hepco & becker

hepco & becker 6307520 00 01 Manuale utente

HOMCOM

HOMCOM AA0-077 Manuale utente

hepco & becker

hepco & becker 6307558 00 01 Manuale utente

Wunderkind Custom

Wunderkind Custom 106503-F15 Guida utente

Dräger

Dräger HPS 3500 Manuale utente

M-WAVE

M-WAVE SKI Manuale utente

Kuryakyn

Kuryakyn 6212 Manuale utente

hepco & becker

hepco & becker 6507504 00 01 Manuale utente

Tool it

Tool it PROMAX LCD 9.13G Manuale utente

Custom Dynamics

Custom Dynamics TruWrapz Manuale utente

Roof

Roof RO200 CARBON Manuale utente

Kabuto

Kabuto Japan IBUKI Manuale utente

PUIG

PUIG 5051 Manuale utente

rizoma

rizoma ZTH050 Manuale utente

Joubert

Joubert 10001711 Manuale utente

Sperian

Sperian Optrel p420 Manuale utente