Epson S5U13L01P00C100 Manuale utente

Rev. 1.3

S1D13L01 Display Controller

S5U13L01P00C100 Evaluation

Board User Manual

Document Number: XA9A-G-001-01.3

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written permission

of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does

not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application

or use in any product or circuit and, further, there is no representation that this material is applicable to products

requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights

is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance

with this material will be free from any patent or copyright infringement of a third party. When exporting the

products or technology described in this material, you should comply with the applicable export control laws and

regulations and follow the procedures required by such laws and regulations. You are requested not to use, to resell,

to export and/or to otherwise dispose of the products (and any technical information furnished, if any) for the devel-

opment and/or manufacture of weapon of mass destruction or for other military purposes.

All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective

companies.

Evaluation Board/Kit and Development Tool Important Notice

1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration, or develop-

ment purposes only. Do not use it for other purposes. It is not intended to meet the requirements of design for finished

products.

2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product.

The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any

kind of damage and/or fire caused by the use of it. The user should cease to use it when any abnormal issue occurs even

during proper and safe use.

3. The part used for this evaluation board/kit or development tool may be changed without any notice.

2Seiko Epson Corporation S5U13L01P00C100 Evaluation Board

Rev. 1.3

S5U13L01P00C100 Evaluation Board Seiko Epson Corporation 3

Rev. 1.3

Table of Contents

Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 CNF[2:0] Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Configuration Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4 Zero Ohm Resistor Configuration . . . . . . . . . . . . . . . . . . . . . . . 11

3.5 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.1 IOVDD, COREVDD, PLLVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.2 3.3V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5.3 Backlight Power Supply for LCD Panel . . . . . . . . . . . . . . . . . . . . . . . 11

3.6 LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 4 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1 CN1, CN2, CN5 Panel Interface Connector . . . . . . . . . . . . . . . . . . . 14

4.2 CN3, CN4 Host Bus Interface Connector . . . . . . . . . . . . . . . . . . . . 14

4.3 P1, P2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board . . . . . . 16

Chapter 5 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.1 Current Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.2 Oscillator Support for CLKI input . . . . . . . . . . . . . . . . . . . . . . 18

5.3 Hardware Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Chapter 6 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Chapter 7 Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Chapter 8 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Chapter 9 Change Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 10 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . 31

4Seiko Epson Corporation S5U13L01P00C100 Evaluation Board

Rev. 1.3

Introduction

S5U13L01P00C100 Evaluation Board Seiko Epson Corporation 5

Rev. 1.3

Chapter 1 Introduction

This manual describes the setup and operation of the S5U13L01P00C100 Evaluation Board. The evaluation board

is designed as an evaluation platform for the S5U13L01 Display Controller.

The S5U13L01P00C100 evaluation board can also connect to the S5U13U00P00C100 USB Adapter board so that

it can be used with a laptop or desktop computer, via USB 2.0. The S5U13L01P00C100 evaluation board can be

used with many native platforms via the host connector which provides the appropriate signals to support a variety

of CPUs. However, if you do not use the S5U13U00P00C100 USB Adapter board, there is prepare the land for the

other host interface. Please use the land to host interface.

This document is updated as appropriate. Please check for the latest revision of this document before beginning any

development. The latest revision can be downloaded at vdc.epson.com.

We appreciate your comments on our documentation. Please contact us via email at

vdc-documentation@ea.epson.com.

Features

6Seiko Epson Corporation S5U13L01P00C100 Evaluation Board

Rev. 1.3

Chapter 2 Features

The S5U13L01P00C100 Evaluation Board includes the following features:

• QFP 128pin S1D13L01F00A100 Display Controller

• Headers for connection to the S5U13U00P00C100 USB Adapter board

Note

The SPI interface is not available when the S5U13L01P00C100 evaluation board is used with the

S5U13U00P00C100 USB adapter board.

• Headers for connection to various host interface

Note

These headers are not mounted. There is only land.

• Headers for connection to various LCD panels

• On-board 24MHz crystal (EPSON SG-210)

• On-board voltage regulator with 1.5V output, for CORE/PLLVDD

• On-board voltage regulator with adjustable 1.5~3.8V output, for IOVDD

• On-board voltage regulator with 3.3V output, for on-board OSC

• On-board voltage regulator with adjustable 38V/60mA max, to provide power for LED back-light of LCD

panels.

Installation and Configuration

S5U13L01P00C100 Evaluation Board Seiko Epson Corporation 7

Rev. 1.3

Chapter 3 Installation and Configuration

The S5U13L01P00C100 evaluation board incorporates a DIP switch, jumpers, and 0 ohm resistors which allow it

to be used with a variety of different configurations.

3.1 CNF[2:0] Configuration

The S1D13L01 has 3 configuration inputs CNF[2:0], which are used to configure the S1D13L01 host interface type

through DIP switch SW1. Depending on the CNF[2:0] setting, some host interface pins will not be used. Those pins

should be terminated by SW2 and SW3.

Note

1. For SW2~3, the setting must be Off if there is no suggestion in table.

2. For JP105~109, the setting must be 1-2 if there is no suggestion in table.

3. Low means internal pull-down for address bus active.

4. The SPI interface is not available when the S5U13L01P00C100 evaluation board is used with the

S5U13U00P00C100 USB adapter board.

Table 3-1: Host Interface Pin Mapping

S1D13L01

Pin Name

Direct 16-bit

Mode 1

Direct 16-bit

Mode 2

Indirect 16-bit

Mode 1

Indirect 16-bit

Mode 2 Direct 8-bit Indirect 8-bit SPI

CNF[2:0] 000 001 010 011 100 101 111

CS# CS# CS# CS# CS# CS# CS# CS#

WR# WR# RDU# WR# RDU# WR# WR# SCK

RD# RD# RDL# RD# RDL# RD# RD# SW2-3=On

UB# UB# WRU# UB# WRU# SW2-1=On SW2-1=On SW2-1=On

LB# LB# WRL# LB# WRL# SW2-2=On SW2-2=On SW2-2=On

AB0 TE (JP108 2-3) TE (JP108 2-3) TE (JP108 2-3) TE (JP108 2-3) AB0 TE (JP108 2-3) TE (JP108 2-3)

AB1 AB1 AB1 P/C# P/C# AB1 P/C# Low

AB[18:2] AB[18:2] AB[18:2] Low Low AB[18:2] Low Low

DB0 DB0 DB0 DB0 DB0 DB0 DB0 SI

DB1 DB1 DB1 DB1 DB1 DB1 DB1 SO

DB[7:2] DB[7:2] DB[7:2] DB[7:2] DB[7:2] DB[7:2] DB[7:2] SW2-5~10=On

DB8 DB8 DB8 DB8 DB8 TE (JP108 3-4) SW3-1=On SW3-1=On

DB[15:9] DB[15:9] DB[15:9] DB[15:9] DB[15:9] SW3-2~8=On SW3-2~8=On SW3-2~8=On

Installation and Configuration

8Seiko Epson Corporation S5U13L01P00C100 Evaluation Board

Rev. 1.3

3.2 Configuration Switches

The S5U13L01P00C100 evaluation board includes the following switch blocks which control the functions

described in Table 3-2: “Switch Settings”. For jumper locations on the evaluation board, see Figure 3-1: “Configu-

ration Switch and Jumper Locations (Red)” on page 10.

Table 3-2: Switch Settings

Switch bit On Off Comment

SW1

1 CNF0 is Pull Up (1) CNF0 is Pull Down (0) CNF[2:0] configuration. See Table

3-1: “Host Interface Pin Mapping”

2 CNF1 is Pull Up (1) CNF1 is Pull Down (0)

3 CNF2 is Pull Up (1) CNF2 is Pull Down (0)

4 not used not used

SW2

1 UB# is Pull Up UB# is not tied

Host interface pin termination when

not used pin. See Table 3-1: “Host

Interface Pin Mapping”

2 LB# is Pull Up LB# is not tied

3 RD# is Pull Up RD# is not tied

4 not used not used

5 DB2 is Pull Down DB2 is not tied

6 DB3 is Pull Down DB3 is not tied

7 DB4 is Pull Down DB4 is not tied

8 DB5 is Pull Down DB5 is not tied

9 DB6 is Pull Down DB6 is not tied

10 DB7 is Pull Down DB7 is not tied

SW3

1 DB8 is Pull Down DB8 is not tied

2 DB9 is Pull Down DB9 is not tied

3 DB10 is Pull Down DB10 is not tied

4 DB11 is Pull Down DB11 is not tied

5 DB12 is Pull Down DB12 is not tied

6 DB13 is Pull Down DB13 is not tied

7 DB14 is Pull Down DB14 is not tied

8 DB15 is Pull Down DB15 is not tied

= suggested settings

Installation and Configuration

S5U13L01P00C100 Evaluation Board Seiko Epson Corporation 9

Rev. 1.3

3.3 Configuration Jumpers

The S5U13L01P00C100 evaluation board includes the following 2-pin, 3-pin, 5-pin and 8-pin jumper blocks which

control the functions described in Table 3-3: “2-Pin Jumper Settings”, Table 3-4: “3-Pin Jumper Settings”, Table

3-5: “5-Pin Jumper Settings” and Table 3-6: “8-PinJumper Setting”. For jumper locations on the evaluation board,

see Figure 3-1: “Configuration Switch and Jumper Locations (Red)” on page 10.

Note

For normal S5U13L01P00C100 operation, JP102 should be in Position 1-2. Also, when using the

S5U13L01P00C100 with the S5U13U00P00C100, JP102 should be in Position 1-2 (JP1 on the

S5U13U00P00C100 must be in Position 1-2). For IOVDD current measurement, JP102 should be removed.

Table 3-5: 5-Pin Jumper Settings

Table 3-3: 2-Pin Jumper Settings

Jumper Position 1-2 No Jumper (Open)

JP101 Connect COREVDD Power Supply Connect a current meter for power measurement

JP102 NOTE Connect IOVDD Power Supply to S5U13U00P00C100 No IOVDD Power Supply to S5U13U00P00C100

JP104 Connect PLLVDD Power Supply Connect a current meter for power measurement

= suggested settings

Table 3-4: 3-Pin Jumper Settings

Jumper Position 1-2 Position 2-3 Off

JP105 WR# is from P1 and CN3 WR# is from P2 WR# is not connected

JP106 DB0 is from P1 and CN3 DB0 is from P2 DB0 is not connected

JP107 DB1 is from P1 and CN3 DB1 is from P2 DB1 is not connected

= suggested settings

Jumper Position Function

JP108

Position 1-2 Position 2-3 Position 1-2: AB0 is AB0 (only for Direct 8bit mode)

Position 2-3: AB0 is TE

Position 3-4 Position 4-5 Position 3-4: DB8 is TE (only for Direct 8bit mode)

Position 4-5: DB8 is DB8

= suggested settings

Installation and Configuration

10 Seiko Epson Corporation S5U13L01P00C100 Evaluation Board

Rev. 1.3

Table 3-6: 8-PinJumper Setting

Figure 3-1: Configuration Switch and Jumper Locations (Red)

Jumper Position Function

JP503

Position 1-2 No Jumper In connect case, TPS61161A is Enable

Position 3-4 No Jumper In connect case, Vout = 20mA

Position 5-6 No Jumper In connect case, Vout = 40mA (add connect Position 3-4)

Position 7-8 No Jumper In connect case, Vout = 60mA (add connect Position3-4 and

Position5-6)

= suggested settings

Altri manuali per S5U13L01P00C100

Indice

Altri manuali Epson Scheda madre

Epson

Epson S5U13A04B00C Manuale utente

Epson

Epson S5U12517P00C100 Manuale utente

Epson

Epson S5U13706B00C Manuale utente

Epson

Epson S5U13700B00C Manuale utente

Epson

Epson S1D13743 Manuale utente

Epson

Epson S1R72V18 Manuale utente

Epson

Epson S5U13781R00C100 Manuale utente

Epson

Epson S5U13706P00C100 Manuale utente

Epson

Epson S5U1C31D51T1 Manuale utente

Epson

Epson S5U13A05P00C100 Manuale utente

Epson

Epson S5U13700B00C Manuale utente

Epson

Epson S5U13C00P00CX00 Manuale utente

Epson

Epson S5U13L03P00C100 Manuale utente

Epson

Epson S5U13781R00C10M Manuale utente

Epson

Epson S5U13U11 Manuale utente

Epson

Epson S1V30080F00A300 Manuale utente

Epson

Epson Buzzer S1C31D51 Manuale utente

Epson

Epson S5U13L02P00C100 Manuale utente

Epson

Epson S5U13706P00C100 Manuale utente

Epson

Epson S1V3034x Series Guida

Epson

Epson S5U13781R01C100 Manuale utente

Epson

Epson S1V30120 Manuale utente

Epson

Epson S5U1C31D50T1 Manuale utente

Epson

Epson S5U13506P00C100 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente