Epson S5U13L03P00C100 Manuale utente

Revision 1.0

S1D13L03 Simple LCDC

S5U13L03P00C100 Evaluation Board

User Manual

Page 2 Epson Research and Development

Vancouver Design Center

S1D13L03 S5U13L03P00C100 Evaluation Board User Manual

XB1AG001 Issue Date: 2014/05/15

Revision 1.0

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko

Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any lia-

bility of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or cir-

cuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as,

medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is

no representation or warranty that anything made in accordance with this material will be free from any patent or copyright

infringement of a third party. When exporting the products or technology described in this material, you should comply with

the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You are

requested not to use, to resell, to export and/or to otherwise dispose of the products (and any technical information furnished,

if any) for the development and/or manufacture of weapon of mass destruction or for other military purposes.

All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective companies.

Evaluation Board/Kit and Development Tool Important Notice

1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration, or develop-

ment purposes only. Do not use it for other purposes. It is not intended to meet the requirements of design for finished

products.

2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product.

The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any

kind of damage and/or fire caused by the use of it. The user should cease to use it when any abnormal issue occurs even

during proper and safe use.

3. The part used for this evaluation board/kit or development tool may be changed without any notice.

Epson Research and Development Page 3

Vancouver Design Center

S5U13L03P00C100 Evaluation Board User Manual S1D13L03

Issue Date: 2014/05/15 XB1AG001

Revision 1.0

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Configuration DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.2 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.2 Voltage Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.3 S1D13L03 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.3 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.4 Power Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.5 Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.5.1 Direct Host Bus Interface Support . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.5.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board . . . . . . . . . 15

4.6 LCD Panel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.7 GPIO Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6 Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

7 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Page 4 Epson Research and Development

Vancouver Design Center

S1D13L03 S5U13L03P00C100 Evaluation Board User Manual

XB1AG001 Issue Date: 2014/05/15

Revision 1.0

Epson Research and Development Page 5

Vancouver Design Center

S5U13L03P00C100 Evaluation Board User Manual S1D13L03

Issue Date: 2014/05/15 XB1AG001

Revision 1.0

1 Introduction

This manual describes the setup and operation of the S5U13L03P00C100 Evaluation

Board. The evaluation board is designed as an evaluation platform for the S1D13L03

Simple LCD Controller.

The S5U13L03P00C100 Evaluation Board can also connect to the S5U13U00P00C100

USB Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0.

However, if you do not use the S5U13U00C100 USB Adapter board, there is no headers

mounted for the other host interface. (only allocated space) Please use the allocated space

mount the headers for the host interface.

This user manual is updated as appropriate. Please check the Epson Electronics America

Website at www.vdc.epson.com for the latest revision of this document before beginning

any development.

We appreciate your comments on our documentation. Please contact us via email at

documentati[email protected]pson.com.

Page 6 Epson Research and Development

Vancouver Design Center

S1D13L03 S5U13L03P00C100 Evaluation Board User Manual

XB1AG001 Issue Date: 2014/05/15

Revision 1.0

2 Features

The S5U13L03P00C100 Evaluation Board includes the following features:

• 176-pin QFP S1D13L03 Simple LCD Controller

• Headers for connection to the S5U13U00P00C100 USB Adapter board

• Header with all S1D13L03 Host Bus Interface signals (optional)

Note

These headers are not mounted. There are allocated areas for mounting.

• Headers for connecting to LCD panels

• Header for S1D13L03 GPIO pins (optional)

Note

These headers are not mounted. There are allocated areas for mounting

• On-board 4MHz oscillator

• 3.3V input power

• On-board voltage regulator with 1.5V output

• On-board voltage regulator with adjustable 38V/60mA max, to provide power for LED

back-light of LCD panel.

Epson Research and Development Page 7

Vancouver Design Center

S5U13L03P00C100 Evaluation Board User Manual S1D13L03

Issue Date: 2014/05/15 XB1AG001

Revision 1.0

3 Installation and Configuration

The S5U13L03P00C100 Evaluation Board incorporates a DIP switch, jumpers, and 0 ohm

resistors which allow it to be used with a variety of different configurations.

3.1 Configuration DIP Switch

The S1D13L03 has 3 configuration inputs (CNF[2:0]). A DIP switch (SW1) is used to

configure CNF[2:0] as described below.

The following figure shows the location of DIP switch SW1 on the S5U13L03P00C100

board.

Figure 3-1: Configuration DIP Switch (SW1) Location

Table 3-1: Summary of Power-On/Reset Options

S5U13L03P00C100

SW1-[4:1] Config S1D13L03

CNF[2:0] Config Power-On/Reset State

1 (ON) 0 (OFF)

SW1-[1] CNF0 Host Data lines are normal Host data lines are swapped

SW1-[2] CNF1 Host Data is 16-bit Host data is 8-bit

SW1-[3] CNF2 PIOVDD output current = 6.5mA PIOVDD output current = 2.5mA

SW1-[4] - not used

= Required settings when using S5U13U00P00C100 USB Adapter board

Page 8 Epson Research and Development

Vancouver Design Center

S1D13L03 S5U13L03P00C100 Evaluation Board User Manual

XB1AG001 Issue Date: 2014/05/15

Revision 1.0

3.2 Configuration Jumpers

The S5U13L03P00C100 Evaluation Board has 6 jumpers which configure various board

settings. And this board has 8-pin jumper for setting back-light of the LDC panel. The

jumper positions for each function are shown below.

Table 3-2: Configuration Jumper Setting

Table 3-3: 8-PinJumper Setting

Jumper Function Position 1-2 Position 2-3 No Jumper

JP1 COREVDD Normal — COREVDD current

measurement

JP2 PLLVDD Normal — PLLVDD current

measurement

JP3 IOVDD Normal — IOVDD current

measurement

JP4 IOVDD Source H1 connector, pin 32 3.3VDD —

JP5 PIOVDD Normal — PIOVDD current

measurement

JP6 PIOVDD Source H4 connector, pin 8 3.3VDD —

= Required settings when using S5U13U00P00C100 USB Adapter board

Jumper Position Function

JP7

Position 1-2 No Jumper In connect case, TPS61161A is Enable

Position 3-4 No Jumper In connect case, Vout = 20mA

Position 5-6 No Jumper In connect case, Vout = 40mA (add connect Position 3-4)

Position 7-8 No Jumper In connect case, Vout = 60mA (add connect Position3-4 and

Position5-6)

= suggested settings

Epson Research and Development Page 9

Vancouver Design Center

S5U13L03P00C100 Evaluation Board User Manual S1D13L03

Issue Date: 2014/05/15 XB1AG001

Revision 1.0

JP1, JP2, JP3, JP5 - Power Supplies for the S1D13L03

JP1, JP2, JP3, JP5 can be used to measure the current consumption of each S1D13L03

power supply.

When the jumper is at position 1-2, normal operation is selected.

When no jumper is installed, the current consumption for each power supply can be

measured by connecting an ammeter to pin 1 and 2 of the jumper.

The jumper associated with each power supply is as follows:

JP1 for COREVDD

JP2 for PLLVDD

JP3 for IOVDD

JP5 for PIOVDD

Figure 3-2: Configuration Jumper Locations (JP1, JP2, JP3, JP5)

Page 10 Epson Research and Development

Vancouver Design Center

S1D13L03 S5U13L03P00C100 Evaluation Board User Manual

XB1AG001 Issue Date: 2014/05/15

Revision 1.0

JP4 - IOVDD Source

JP4 is used to select the source for the IOVDD supply voltage.

When the jumper is at position 1-2, the IOVDD voltage must be provided to the H1

connector, pin 32.

When the jumper is at position 2-3, the IOVDD voltage is provided by the 3.3V power

supply of the board.

Note

H1 connector is not mounted. There is an allocated area for mounting.

JP6 - SIOVDD Source

JP6 is used to select the source for the PIOVDD supply voltage.

When the jumper is at position 1-2, the PIOVDD voltage must be provided to the H4

connector, pin 8.

When the jumper is at position 2-3, the PIOVDD voltage is provided by the 3.3V power

supply of the board.

Note

H4 connector is not mounted. There is an allocated area for mounting.

JP7 - Backlight Power Supply for LCD Panel

The S5U13L03P00C100 Evaluation Board is designed to generate backlight power supply

for LCD panels from 3.3V via the S5U13U00P00C100 USB Adapter Board or connector

H1. The 3.3V must be supplied from the S5U13U00P00C100 or H1. The

S5U13L03P00C100 has incorporated a White LED Driver Controller(TPS61161A)for the

panel backlighat. The White LED Driver Controller drives the panel at a constant current.

The S5U13L03P00C100 is capable of changing the output current (20mA, 40mA,

60mA/Max 38V). The current is adjusted by connection of JP7 “See Table 3.3: 8-Pin

Jumper Setting”

Note

H1 connector is not mounted. There is an allocated area for mounting

Indice

Altri manuali Epson Scheda madre

Epson

Epson 5U13743P00C100 Manuale utente

Epson

Epson S1R72V18 Manuale utente

Epson

Epson S1V30333 Manuale utente

Epson

Epson S1V30120 Manuale utente

Epson

Epson S1S65010 Manuale utente

Epson

Epson SG-WRITERII Istruzioni per l’uso

Epson

Epson S5U13A05B00C Manuale utente

Epson

Epson S5U13A05P00C100 Manuale utente

Epson

Epson S5U13781R01C100 Manuale utente

Epson

Epson S5U13706P00C100 Manuale utente

Epson

Epson S5U13515P00C100 Manuale utente

Epson

Epson S1R72U06 Manuale utente

Epson

Epson S1V30000 Series Guida utente

Epson

Epson S5U13T04P00C100 Manuale utente

Epson

Epson S5U1C17M03T Manuale utente

Epson

Epson S1R72U16 Manuale utente

Epson

Epson S5U13L01P00C100 Manuale utente

Epson

Epson S5U1C31D51T1 Manuale utente

Epson

Epson S1V30080F00A300 Manuale utente

Epson

Epson S5U13U00P00C100 Manuale utente

Epson

Epson S5U13L01P00C100 Manuale utente

Epson

Epson Buzzer S1C31D51 Manuale utente

Epson

Epson S5U13506P00C100 Manuale utente

Epson

Epson S5U13513P00C100 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente