EUTECH INSTRUMENTS TDScan Low Manuale utente
+
+
INC
DEC
•Waterproof & Floats
•ReplaceableElectrode
•Auto-off
•AutomaticTemperature
Compensation(ATC)
Diagram 1
Openthisleafletforcalibration/testing/maintenance
instructions.
Changing Batteries
1. Open battery
compartment
lid (with
attached
lanyardloop).
2. Remove old
batteries;
replace
with fresh
ones. Note
polarity as
showninbatterycompartment.SeeDiagram1.
3. Recalibrateafterbatterychange.
Warranty
Eutech Instruments warrants its meter free from
manufacturing defects for 2 years and electrode
module for 6 months. If repair, adjustment or
replacementisnecessaryandhasnotbeentheresult
of abuse or misuse within the time period, please
returnthetester–freightprepaid–andcorrection
willbemadewithoutcharge.Outofwarrantyproducts
will be repaired on a charge basis.
Return Of Items
Authorization must be obtained from Eutech’s
distributor before returning items for any reason.
When applying for authorization, please include
informationregardingthereasontheitem(s)areto
bereturned.
Note:Wereservetherighttomakeimprovementsin
design, construction and appearance of products
withoutnotice.Pricesaresubjecttochangewithout
notice.
Waterproof ECScan High Instructions
Before You Begin
Removeelectrodecap.Soakelectrodeforafew
minutes in alcohol to remove oils.
Calibration
Tester is factory calibrated. However, to ensure
accuracy,calibrateconductivityonaregularbasis.
Selectacalibrationstandardappropriateforthe
ECScan High tester (between 2.00 mS and
19.90mS).Itisbesttoselectastandardclose
tothetestsolutionvalue.
1. Open battery compartment lid (end with
lanyardloop).
2. Orientate the battery compartment as
showninDiagram1.
3.Rinseelectrodeindeionizedwater,then
rinseitincalibrationstandard,thendip it
intoacontainer ofcalibrationstandard.
4. Switch unit on (ON/OFF key). Wait
severalminutesfordisplaytostabilize.
5. Pressthe INCorDEC keyto adjust
reading to match the calibration
standardvalue.
6. After3secondswithoutakeypress,
the display flashes 3 times, then
shows ‘ENT’. The tester accepts
calibration value; returns to
measurementmode.
7. Replacebattery cap.
Conductivity Testing
1. Removeelectrode cap.Switch uniton(ON/OFF
key).
2. Dipelectrodeintotestsolution.Makesuresensor
is fully covered.
3. Wait for reading to stabilize (Automatic
Temperature Compensation corrects for
temperaturechanges).Notereading.
4. PressON/OFFtoturnoff tester.Replaceelectrode
cap. Note: Tester automatically shuts off after
8.5 minutes of non-use.
HOLD Function
PressHOLDkeytofreezedisplay.PressHOLDagain
torelease.
Tester Maintenance
• To improve performance, clean the electrode
byrinsingtheminalcoholfor10to15minutes.
• Replace all batteries if low battery indicator
appears,or ifreadings arefaint orunstable.
• Ifyouexperience drift,periodicallylet electrode
fully dry.
When you need a new electrode, see “Electrode
Replacement” on insert in back of box.
Self-Diagnostic MessagesSelf-Diagnostic Messages
Self-Diagnostic MessagesSelf-Diagnostic Messages
Self-Diagnostic Messages
bAt Weakbatteries–replacewithfreshonesspecified
bymanufacturer.
Err Wrong keypress.
Or,Ur Overrange/Underrangesignal,orelectrode
isnotincontactwithsolution,orelectrodeisfailing.
---- Calibrationmodeactivatedbutnotperformed.
68X247755 11/00 Rev 0
+
+
•Waterproof & Floats
•ReplaceableElectrode
•Auto-off
•AutomaticTemperature
Compensation(ATC)
INC
DEC
Diagram 1
Openthisleafletforcalibration/testing/maintenance
instructions.
Changing Batteries
1. Open battery
compartment
lid (with
attached
lanyardloop).
2. Remove old
batteries;
replace with
fresh ones.
Note polarity
as shown in
batterycompartment.See Diagram1.
3. Recalibrateafterbatterychange.
Warranty
Eutech Instruments warrants its meter free from
manufacturing defects for 2 years and electrode
module for 6 months. If repair, adjustment or
replacementisnecessaryandhasnotbeentheresult
of abuse or misuse within the time period, please
returnthetester–freightprepaid–andcorrection
willbemadewithoutcharge.Outofwarrantyproducts
will be repaired on a charge basis.
Return Of Items
Authorization must be obtained from Eutech’s
distributor before returning items for any reason.
When applying for authorization, please include
informationregardingthereasontheitem(s)areto
bereturned.
Note:Wereservetherighttomakeimprovementsin
design, construction and appearance of products
withoutnotice.Pricesaresubjecttochangewithout
notice.
Waterproof ECScan Low Instructions
68X247754 11/00 Rev 0
Conductivity Testing
1. Removeelectrode cap.Switchunit on(ON/OFF
key).
2. Dip electrode into test solution. Make sure
sensor is fully covered.
3. Wait for reading to stabilize (Automatic
Temperature Compensation corrects for
temperaturechanges).Notereading.
4. Press ON/OFF to turn off tester. Replace
electrode cap. Note: Tester automatically
shuts off after 8.5 minutes of non-use.
HOLD Function
PressHOLDkeytofreezedisplay.PressHOLDagain
torelease.
Tester Maintenance
••
••
• To improve performance, clean the electrode
byrinsingtheminalcoholfor10to15minutes.
• Replace all batteries if low battery indicator
appears,or ifreadings arefaint orunstable.
• Ifyouexperiencedrift,periodicallyletelectrode
fully dry.
When you need a new electrode, see “Electrode
Replacement” on insert in back of box.
Self-Diagnostic MessagesSelf-Diagnostic Messages
Self-Diagnostic MessagesSelf-Diagnostic Messages
Self-Diagnostic Messages
bAt Weak batteries–replace with fresh ones
specified by manufacturer.
Err Wrong keypress.
Or,Ur Overrange/Underrangesignal,orelectrode
isnotincontactwithsolution,orelectrodeisfailing.
---- Calibrationmodeactivatedbutnotperformed.
Before You Begin
Removeelectrodecap.Soakelectrodeforafew
minutes in alcohol to remove oils.
Calibration
Tester is factory calibrated. However, to ensure
accuracy,calibrateconductivityonaregularbasis.
Selectacalibrationstandardappropriateforthe
ECScan Low tester (between 200 µS and
1990 µS).Itisbesttoselectastandardclose
tothetestsolutionvalue.
1. Open battery compartment lid (end with
lanyardloop).
2. Orientate the battery compartment as
showninDiagram1.
3.Rinseelectrodeindeionizedwater,then
rinseitincalibrationstandard,thendipit
intoacontainer ofcalibrationstandard.
4. Switch unit on (ON/OFF key). Wait
severalminutesfordisplaytostabilize.
5.PresstheINCorDECkeytoadjust
reading to match the calibration
standardvalue.
6. After 3 seconds without a key
press, the display flashes 3 times,
thenshows‘ENT’.Thetesteraccepts
calibration value; returns to
measurementmode.
7. Replacebattery cap.
Tester TDScan TDScan ECScan ECScan
Low High Low High
Range 0to 0to 0to 0to
1990 10.00 1990 19.90
ppm ppt µS/cm mS/cm
Resolution 10 0.10 10 0.10
ppm ppt µS/cm mS/cm
Accuracy ±1% Full Scale
TDSfactor 0.4 to 1.0 selectable -
Calibration 200to 2.00to 200to 2.00to
Standard 1990 10.00 1990 19.90
Range ppm ppt µS/cm mS/cm
Calibration 1 point (calibration range is ±30%
of factory default parameter)
ATC 0 to 50 °C
Temp 2% per °C
Coefficient
Operating 0to50°C
Temp
Power Four X 1.5V
Battery (Type:A76,LR 44 or V136A);
> 140 hrs continuous use
Dimension; Tester: 16.5 cmx 3.8 cm;90 g
Weight Boxed: 22 cm x6 cm x 5 cm; 170 g
•Push-buttoncalibration
•Fast,stable,repeatablereadings
•Availablethroughauthorizeddistributors
SPECIFICATIONS
Lanyard
connection
Replaceable
Sensor
Twist-off
Battery
Compartment
ManufacturedBy:
EutechInstrumentsPteLtd
Blk 55, Ayer Rajah Crescent,
#04-14/24, Singapore 139949
Tel: (65)778 6876 Fax: (65)773 0836
E-Mail: [email protected]
Web-Site: http://www.eutechinst.com
MadeinSingapore
68X247828 11/00 Rev 0
A
B
REMOVE THE OLD ELECTRODE
REPLACE THE ELECTRODE
(PictureB)
(PictureA)
You can replace the electrode module
at the fraction of the cost of a new
tester. When the tester fails to calibrate
or gives fluctuating readings in
calibration standards, you need to
change the electrode.
1. With dry hands, grip the ribbed tester
collar with electrode facing you. Twist
the collar counter clockwise (see picture
A). Save the ribbed tester collar and
O-ring for later use.
2. Pull the old electrode module away from
the tester.
3. Align the four tabs on the new module
so that they match the four slots on the
tester (see picture B).
4. Gently push the module onto the slots
to sit it in position. Push the smaller
O-ring fully onto the new electrode
module. Push the collar over the module
and thread it into place by firmly twisting
clockwise.
Electrode Replacement
Water quality testing • water and
Wastewater treatment • hydroponics
• pools • boilers • factories • ecology
studies • and more!
Applications
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali EUTECH INSTRUMENTS Strumento di misura
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CYBERSCAN CON 510 CONDUCTIVITY BENCH METER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS STANDARD TDSCAN 4 CONDUCTIVITY TESTER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS 2700 Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CYBERSCAN PH 300310 PORTABLE METER Istruzioni per il montaggio
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS ?lpha-pH550 Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS STANDARD TDSCAN 2 TDS TESTER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS Oakton CON 510 Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CON 700 - REV 3 Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CYBERSCAN PHION 510 PHION METER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CyberScan PCD 650 Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS DISSOLVED OXYGEN PROBE Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS WATERPROOF EC Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS Oakton 450 Series Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS STANDARD TDSCAN 1 TDS TESTER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS STANDARD PHSCAN 2 PH TESTER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS WATERPROOF PHTESTER 102030BNC Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS TURBIDIMETER TN-100 WATERPROOF PORTABLE... Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS 450 Series Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS COND 6 PLUS Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS WATERPROOF TDSCAN 4 CONDUCTIVITY TESTER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CYBERSCAN PC 5000 PHCONDUCTIVITY METER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CYBERSCAN PC 10 COMBINATION PHCONDUCTIVITY... Istruzioni per il montaggio
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS CYBERSCAN PH 10 PHMV METER Manuale utente
EUTECH INSTRUMENTS
EUTECH INSTRUMENTS WATERPROOF PHTESTR 2 PH TESTER Manuale utente
