Extech Instruments ExStik FL700 Manuale utente

User Guide

ExStik®FL700

Fluoride Meter

FL700-en-US_V1.4 09/14

Introduction

The model FL700 is a system specifically designed for the quick and accurate measurement of

fluoride ions in drinking water and other aqueous samples. Unlike other electrode based systems

the FL700 consists of the sensing electrode, measuring electronics, and the display in one

convenient package. This meter is shipped fully tested; with proper use, this instrument will

provide years of reliable service.

Features

Automatic temperature compensation (±10oC of calibration temperature)

Automatic calibration

Stability sensing to optimize accuracy

Internal Datalogger for storing up to 25 readings

Direct reading of ppm, mV, or mg/l units

Automatic power off after 12 minutes to preserve battery life

Internal error detection

FL700-en-US_V1.4 09/14

Description

Meter Description

1. Battery compartment cover

2. LCD Display

3. MODE/HOLD button

4. CAL/RECALL button

5. ON/OFF button

6. Electrode Retaining Collar (ring)

7. Electrode Sensor

(Note: The Electrode storage cap is not shown this diagram)

Electrode Sensor Description

The sensing electrode is a europium doped lanthanum fluoride single

crystal that has been incorporated into a removable sensing module that

houses a reference electrode and temperature measurement system. The

high resistance electrode signals are impedance converted to a low resistance output in the

sensing module to ensure stable and noise free performance.

Reagent Tablets

The FL700 allows the users to follow the ASTM and EPA standard methodology using any of the

TISAB reagents and standards already in use. Also, Extech has developed tablet-form TISAB

which contains all of the essential and approved chemicals that are found in the usual TISAB

reagents. A total ionic strength adjustment buffer (TISAB) is a buffer solution which increases

the ionic strength of a solution to a relatively high level.

The “dry” TISAB reagent does not contribute to sample dilution. The benefits of this method are:

1. No volumetric errors

2. Independent of sample size (± 20% of nominal sample volume)

3. Easy to use in the field or laboratory

4. Can be shipped more easily than liquid reagents

5. Lower cost per test

LCD Display

1. Bargraph display

2. Measurement units

3. Main display

4. Low (L) and High (H) Calibration icons

5. Data HOLD indicator

6. Low Battery indicator

7. Temperature display

FL700-en-US_V1.4 09/14

Operation

Preparation for use

1. Remove the FL700, electrode module and sample cup from its box. Remove caps from

module

2. If not already done, fit the electrode module onto the end of the meter body, making sure

that the slots line up correctly, and turn the module retaining ring to secure the assembly.

Powering the FL700

Press the ON/OFF button to turn the meter on or off. If the batteries are weak, the ‘BAT’

indicator appears on the LCD.

Power-On Diagnostics

1. When the meter is switched ON the LCD displays “SELF” and “CAL” while the meter runs a

diagnostic routine

2. During this time the meter is recalling the user calibration data, performing self diagnostics &

initializing the circuitry

3. When completed, the meter proceeds to the normal measurement mode

Calibration

The FL700 can be calibrated between 1.0 ppm and 10 ppm or between 0.5 and 5.0 ppm Fluoride

ion. Set the Mode to ppm. The following calibration procedure assumes the normal 1.0 to 10 ppm

range has been chosen.

1. Prepare a 1 ppm fluoride standard solution by placing one TISAB tablet into a sample cup

and add 20 mls of the 1ppm Fluoride standard into the sample cup.

Note: if your 1ppm Fluoride standard already contains TISAB do not use a TISAB tablet.

2. Create a rinse solution that can be used between sample measurements buy dissolving

1 TISAB tablet in 20ml of Distilled water. The rinse solution promotes faster response times.

3. Rinse the end of the FL700 module in this Rinse solution or in Distilled water and then wipe

thoroughly with a paper tissue.

4. Place the FL700 into the prepared 1 ppm standard and switch the instrument ON using the

ON/OFF button. The instrument will now go through its self-calibration.

5. The instrument will enter HOLD mode in about 35 seconds when stabilized in the 1.0 ppm

standard solution.

6. Press and HOLD the CAL key, CAL will appear in the display followed by 0.5ppm and

5.0ppm. Continue holding the CAL button until 1.0 ppm and CAL appear in the display.

Release the CAL key.

7. Wait until the display stops blinking; the instrument will enter the normal measurement

mode.

8. The instrument is now calibrated and ready for use.

9. The circled L and H icons on the display indicate that the low range (L) and high range (H)

calibrations have been completed.

Calibration frequency

Calibrate the FL700 prior to each new measurement batch or if more than 12 hours has elapsed

since the last calibration.

FL700-en-US_V1.4 09/14

Other standards

The FL700 can also be calibrated between 0.5 and 5.0 ppm F. Follow the calibration instructions

above but substitute 0.5 ppm for 1.0 ppm and 5.0 ppm for 10 ppm.

Slope Adjustment

1. Slope adjustment although not a frequent requirement can be carried out by following the

instructions in Calibration steps above except for the fact that a 10 ppm standard is used after

calibrating with the 1 ppm standard

2. Press the Cal button until 10 ppm appears. Slope adjustment is then complete.

Measurement Mode

1. Prepare 20ml of test solution by adding one TISAB reagent to the unknown sample.

Thoroughly wipe the end of the FL700. Wait for the tablet to dissolve and then mix thoroughly

before proceeding.

2. Rinse the end of the FL700 in your rinse solution or in distilled water, wipe dry.

3. Place the FL700 into the prepared unknown sample. If the instrument is in the HOLD mode,

press MODE/HOLD to unlock HOLD

4. After ~35 seconds, the instrument will display the value of the unknown concentration and will

then enter the HOLD mode

Note: The readings can be stored in the memory by pressing the MODE/HOLD key for ~ 3 seconds.

Electrode Storage

1. It is recommended that the electrode be stored WET in the last test solution used by the

instrument (fluoride ion plus TISAB reagent).

2. The module and can be stored dry. If stored dry it will be necessary to allow approximately 15

minutes of soaking in a fluoride solution before the specified performance can be achieved.

The instrument will give an error code when the electrode can no longer be calibrated

Temperature Units (ºF / ºC)

1. With the unit OFF, press and hold the CAL/RECALL button

2. With the CAL/RECALL button depressed, momentarily press the ON/OFF button to turn the

unit ON

3. The CAL/RECALL button can be released when ‘Self Cal’ is shown in the display

4. To switch back to the previous unit of measure, repeat steps 1 through 3.

Units of Measure

The FL700 has 3 different units of measure. (ppm, mV, and mg/l).

To change the units of measure follow these steps:

1. Turn on the meter.

2. Press and Hold the MODE/HOLD button and it will cycle through the 3 different units of

measure (ppm, mV, mg/L).

3. Release the Mode/Hold button when the preferred unit is selected.

FL700-en-US_V1.4 09/14

Auto-Power OFF Feature

The auto power off feature automatically shuts the meter off 12 minutes after the most recent button

press.

Disabling the Auto-Power OFF Feature

With the unit ON, momentarily press the CAL/RECALL button, then quickly press and hold both the

MODE/HOLD and ON/OFF buttons until ‘oFF’ is displayed. To restore the Auto Power Off Feature

(auto power OFF enable) simply turn the meter off and on again using the ON/OFF button.

Low Battery Indication

When the battery voltage falls below the operating threshold, ‘BAT’ will appear on the display. Refer

to the Maintenance section for battery replacement information.

Storing Readings

Up to 25 readings can be stored in memory for later recall.

1. With the meter in the HOLD mode, press and hold the MODE/HOLD button for three (3)

seconds to store a reading. Release the button when the memory location number appears on

the lower display.

2. After approx. 30 seconds (measurement duration) the meter will return to the HOLD mode and

another reading can then be stored.

3. If more than 25 readings are stored, previously stored readings (starting with reading number

1) are overwritten.

Recalling Stored Readings

1. Momentarily press the CAL/RECALL button and then within 4 seconds momentarily press the

MODE/HOLD. The last stored data point location will be displayed (1 to 25). Each time the

MODE/HOLD button is momentarily pressed the next most recently stored data point will be

displayed.

2. After the last data point is displayed, pressing the MODE/HOLD button again returns the

display to the beginning of the list.

3. Pressing the CAL/RECALL button at anytime stops the data retrieval process and returns the

meter to the normal measurement mode.

Clearing Stored Readings

1. With the unit ON press and hold the ON/OFF button for 4 seconds

2. When “CLR” is shown in the main display the memory is cleared.

FL700-en-US_V1.4 09/14

Maintenance

Battery Replacement

1. Twist off the battery compartment cover

2. Holding the battery housing in place with a finger, pull out the battery carrier using the two

small tabs

3. Replace the four (4) CR2032 batteries observing proper polarity

4. Replace the battery carrier, reattach the battery compartment cap and tighten securely

Electrode Replacement

1. To remove the electrode, first turn the instrument OFF and then unscrew and remove the

electrode retaining collar. (turn the collar counter-clockwise to remove)

2. Gently rock the electrode from side to side, pulling it away from the meter until it disconnects

3. To attach an electrode, align the positioning “keys” on the electrode and the main body

housing and then carefully push the electrode into the meter socket until it is fully seated

4. Tighten the electrode retaining collar firmly enough to seal the electrode with the meter

Electrode Storage

3. It is recommended that the electrode be stored wet in the last test solution used by the

instrument (fluoride ion plus TISAB reagent).

4. The module and can be stored dry. If stored dry it will be necessary to allow approximately 15

minutes of soaking in a fluoride solution before the specified performance can be achieved.

The instrument will give an error code when the electrode can no longer be calibrated

FL700-en-US_V1.4 09/14

Specifications

Range 0.10 to 9.99ppm (mg/l)

Accuracy ± 3% of reading or ± 0.1ppm (whichever is greater)

Resolution 0.1ppm

Display 2000 count, Dual function 3 ½ digit LCD with Bargraph,

Display size: 24 mm x 20 mm

Electrode Europium doped lanthanum fluoride single crystal

Electrode life 6 months minimum

Measurement method In compliance with EPA Method 340.2 (Potentiometric Ion

Selective Electrode)

Response Time 90% of change in less than 30 seconds (typical)

Operating Temp. Range 32 to 140°F (0 to 60°C)

ATC Range 32 to 140°F (0 to 60°C)

Measurement Storage 25 tagged (numbered) data sets with recall

Battery Power Four (4) CR2032 button batteries

Low Battery Indication ‘BAT’ appears on the LCD

Auto Power Off After 12 minutes of inactivity

Dimensions/Weight 1.4 x 6.8 x 1.6” (36 x 173 x 41mm); 7.4 oz (210g)

FL700-en-US_V1.4 09/14

Warranty

FLIR Systems, Inc. warrants this Extech Instruments brand device to be free of defects in parts and

workmanship for one year from date of shipment (a six month limited warranty applies to sensors and cables). If it

should become necessary to return the instrument for service during or beyond the warranty period, contact the

Customer Service Department for authorization. Visit the website www.extech.com for contact information. A Return

Authorization (RA) number must be issued before any product is returned. The sender is responsible for shipping

charges, freight, insurance and proper packaging to prevent damage in transit. This warranty does not apply to

defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper

maintenance or repair, or unauthorized modification. FLIR Systems, Inc. specifically disclaims any implied warranties

or merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, incidental or

consequential damages. FLIR’s total liability is limited to repair or replacement of the product. The warranty set forth

above is inclusive and no other warranty, whether written or oral, is expressed or implied.

Calibration, Repair, and Customer Care Services

FLIR Systems, Inc. offers repair and calibration services for the Extech Instruments

products we sell. NIST certification for most products is also provided. Call the Customer

Service Department for information on calibration services available for this product.

Annual calibrations should be performed to verify meter performance and accuracy.

Technical support and general customer service is also provided, refer to the contact

information provided below.

www.extech.com

SupportLines:U.S.(877)439‐8324;International:+1(603)324‐7800

TechnicalSupport:Option3;E‐mail:[email protected]

Repair&Returns:Option4;E‐mail:[email protected]

Productspecificationsaresubjecttochangewithoutnotice

Pleasevisitourwebsiteforthemostup‐to‐dateinformation

www.extech.com

FLIRCommercialSystems,Inc.,9TownsendWest,Nashua,NH03063USA

ISO9001Certified

FL700-en-US_V1.4 09/14

Garantie

FLIR Systems, Inc. garantit que cet appareil Extech Instruments est exempt de défauts matériaux et de

fabrication pendant un an à partir de la date d’envoi (une garantie limitée de six mois s’applique aux capteurs et aux

câbles). Si le renvoi de l’appareil pour réparation devient nécessaire durant ou après la période de garantie,

contactez le service client pour autorisation. Pour obtenir les coordonnées, visitez le site Web suivant :

www.extech.com. Un numéro d’autorisation de retour (AR) doit être délivré avant tout retour de produit. L’expéditeur

prend à sa charge les frais d’expédition, le fret, l’assurance et l’emballage correct de l’appareil afin de prévenir toute

détérioration durant le transport. Cette garantie ne s’applique pas aux dommages imputables à l’utilisateur, tels que

l’usage impropre ou abusif, un mauvais câblage, une utilisation non conforme aux spécifications, un entretien ou une

réparation incorrecte, ou toute modification non autorisée. FLIR Systems, Inc. déclinera spécifiquement toute

garantie ou qualité marchande ou aptitude à l’emploi prévu, et ne sera en aucun cas tenu responsable pour tout

dommage conséquent, direct, indirect ou accidentel. La responsabilité totale de FLIR est limitée à la réparation ou au

remplacement du produit. La garantie définie ci-dessus est inclusive et aucune autre garantie, écrite ou orale, n’est

exprimée ou implicite.

Calibrage, réparation et services après-vente

FLIR Systems, Inc. offre des services de calibrage et de réparation pour les produits

Extech Instruments que nous commercialisons. Nous fournissons également une

certification NIST pour la plupart des produits. Contactez notre service client pour toute

information sur les services de calibrage disponibles pour ce produit. Un calibrage doit être

effectué chaque année pour vérifier les performances et la précision du mètre. Nous

offrons également une assistance technique et un service à la clientèle. Veuillez vous

reporter aux coordonnées fournies ci-dessous.

www.extech.com

Lignesd’assistance:États‐Unis(877)439‐8324;international:+1(603)324‐7800

Serviced’assistancetechnique:Option3;E‐mail:[email protected]

Réparationsetretours:Option4;E‐mail:[email protected]

Lesspécificationsproduitsontsujettesàmodificationssanspréavis.

Pourlestoutesdernièresinformations,veuillezvisiternotresiteWeb.

www.extech.com

FLIRCommercialSystems,Inc.,9TownsendWest,Nashua,NH03063USA

CertifiéISO9001

Indice

Altri manuali Extech Instruments Strumento di misura

Extech Instruments

Extech Instruments UM200-NIST Manuale utente

Extech Instruments

Extech Instruments RF153 Manuale utente

Extech Instruments

Extech Instruments HD780 Manuale utente

Extech Instruments

Extech Instruments 461995 Manuale utente

Extech Instruments

Extech Instruments 382090 Manuale utente

Extech Instruments

Extech Instruments EasyView EA33 Manuale utente

Extech Instruments

Extech Instruments 403125 Manuale utente

Extech Instruments

Extech Instruments 407303 Manuale utente

Extech Instruments

Extech Instruments 451212 Manuale utente

Extech Instruments

Extech Instruments SDL700 Manuale utente

Extech Instruments

Extech Instruments MO270 Manuale utente

Extech Instruments

Extech Instruments VT30-E Manuale utente

Extech Instruments

Extech Instruments MO55 Manuale utente

Extech Instruments

Extech Instruments EX622 Manuale utente

Extech Instruments

Extech Instruments AN100 Manuale utente

Extech Instruments

Extech Instruments 406800 Manuale utente

Extech Instruments

Extech Instruments EC170 Manuale utente

Extech Instruments

Extech Instruments SP505 Manuale utente

Extech Instruments

Extech Instruments SDL100-NIST Manuale utente

Extech Instruments

Extech Instruments 461700 Manuale utente

Extech Instruments

Extech Instruments PH90 Manuale utente

Extech Instruments

Extech Instruments 461891 Manuale utente

Extech Instruments

Extech Instruments 401036 Manuale utente

Extech Instruments

Extech Instruments MA250 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente