Extron electronics SI 26 Manuale utente

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Kyodo Building

16 Ichibancho

Chiyoda-ku, Tokyo 102-0082 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

User’s Manual

DRAFT COPY

Surface Mount Speakers

68-1164-01

Rev. Ax1

05 06

SI 26 and SI 28

SI 26 and SI 28 Speakers • Introduction 1

About the SI 26 and SI 28 Speakers

The Extron System INTEGRATOR™ SI 26 and SI 28 two-way

surface mount speakers are ideally suited for classrooms,

conference rooms, and boardrooms. With a weather resistant

construction, they are also suitable for outdoor environments.

• SI 26 features a 6.5" long-throw woofer, 1" tweeter, 150 watts

continuous program capacity, and frequency response from 70

Hz to 20 kHz.

• SI 28 features an 8" long-throw woofer, 1" tweeter, 180 watts

continuous program capacity, and frequency response from 50

Hz to 20 kHz.

Figure 1 — Extron SI surface speakers

NExtron recommends that the wiring installation is

performed by a professional audio equipment installer.

CUse cable clamps to hold the cables in place for

strain relief. Trim back/insulate exposed cable

shields with heat shrink to reduce the chance of short

circuits

Introduction

Features

Dimensions: SI 26: 13.0" H x 8.5" W x 6.75" D

(33.0 cm H x 21.6 cm W x 17.1 cm D)

SI 28: 16.5" H x 11.5" W x 8.6" D

(41.9 cm H x 29.2 cm W x 21.9 cm D)

aDual tuned bass reﬂex ports

b1" ferroﬂuid-cooled, aluminum dome tweeter

cFront locking access (allows for speaker position adjustment)

d6.5" (SI 26) or 8" (SI 28) long-throw woofer

eGrill and enclosure may be painted to match environment

fWeather resistant construction

gPush down spring terminals

h Wall mount assembly with unique V-Lock™ (Patent Pending)

system included

iBack cover for use when speakers are not wall mounted

jAllen hex tool

kExtron logo (ﬁts in grill to cover locking port access)

l8 ohm nominal impedance

m 75 watts (SI 26) or 90 watts (SI 28) continuous pink noise

n 150 watts (SI 26) or 180 watts (SI 28) continuous program

oInternal driver overload protection circuit

N For items 12 through 15, see "Speciﬁcations", page 7

of this manual.

Figure 1 — Speaker Features

SI 26 and SI 28 Speakers • Features

SI 26 and SI 28 Speakers • Introduction

Installation

Installing the SI 26 or SI 28 Speaker

The SI 26 or SI 28 can be mounted on a surface, such as a wall

or post, or mounted in a bookcase, or under a shelf, and can be

used with any Extron product with power amps.

Conference Room

Extron

SI 28

Surface-mount Speakers

Figure 2 — Surface speaker application

Desk top or bookshelf applications

1. For quick installation on a desk top or bookshelf, simply

place on a desk, shelf or other ﬂat surfaces as desired.

NDo not detach the back cover.

2. Route the speaker wire (Extron recommends using

12-18 AWG) to the speakers.

3. Strip the wire and connect the speakers as described on

page 6.

Wall mounting

1. If mounting to drywall, use a stud locator to locate the

studs in the wall. Mark their position.

2. Remove the wall mount assembly from the box and

loosen the hex cap screw (by turning it counter clockwise)

with the allen hex tool supplied. Rotate the front section

approximately 90 degrees to the rear mounting plate (see

ﬁgure 3) and tighten the hex cap screw, locking the plate in

position. This will make the next steps easier to perform.

Fasten the

wall mount plate

to the vertical

surface.

Rotate This

Section 90°

Figure 3 — Rotating and mounting the wall mount

assembly

3. Mark the location of the wall mount plates three center

holes on the stud line and drill the pilot holes.

NFor some surfaces the four alternative pilot dimples

(see ﬁgure 4) may be used to secure the assembly in place.

Mark and drill as appropriate

Alternative

pilot dimples.

Figure 4 — Alternative pilot dimples on the speaker

bracket

4. Mark the wall where the wire will pass through the plate,

and cut a small access hole large enough for the wire to

pass through without snagging. If the stud is wider than

the plates access hole, then cut the hole in the wall to the

left or right and directly alongside the stud (see ﬁgure 5).

Before cutting it, make sure the plate will cover the hole

when it is ﬁnally installed.

SI 26 and SI 28 Speakers • Installation

4SI 26 and SI 28 Speakers • Installation

Installation, cont’d

Cut access

hole alongside

stud and feed

wires though

hole.

Wall Stud

Wall Mount Assembly

Wall

Approximate Stud

line behind wall

Bend wire to line

up with access

hole in plate.

Screw

Figure 5 — Install wall mount assembly

NExtron recommends that the wiring installation is

performed by a professional audio equipment installer.

5. Using compatible speaker wire (Extron recommends using

12-18 AWG), route the wire from the audio source to the SI

speaker location by the most convenient and safe route. If

the wiring is to remain hidden behind the wall, follow the

stud to where the small access hole has been cut, and feed

about two feet of wire out through the hole into the room.

If necessary, bend the wire to align with the plate (see

ﬁgure 5). Secure the wire at various places to the stud, but

allow enough freedom of movement near to the hole for

connection to the speaker

6. Pull sufficient wire up through the holes in the rear plate

(see figure 6) to allow ease of connection to the speaker

after installation.

Pass the wires

through the plate

access hole.

Figure 6 — Pass the wire through the plate

7. Place the wall mount assembly against the wall, aligning

the plate holes with those drilled, and secure with

appropriate hardware.

SI 26 and SI 28 Speakers • Installation

8. When the assembly is securely in place, loosen the hex

cap screw (turn counter-clockwise) and rotate the front

section back into a vertical position with the hex cap screw

at the top. Using the allen hex tool, turn the hex cap screw

clockwise to tighten.

9. Remove the cover from the back of a speaker and carefully

slide the speaker box bracket down into the V lock groove

until it locks into place (see ﬁgure 7).

Slide the speaker onto the

wall mount assembly.

Stage

Box

bracket

Figure 7 — Install speaker onto the wall mount

assembly

10. To adjust the angle of the speaker, carefully remove the

Extron logo on the front of the speaker to expose the front

locking access (see Figure 1, Item 3, for location). Insert the

allen hex tool into the locking access, and slightly loosen

the hex cap screw. Adjust the speaker to the desired angle

(see ﬁgure 8), and torque the cap screw down clockwise

until snug. The speaker will sit securely in the desired

position. Install the Extron logo.

NThe Extron logo can be ﬁtted either horizontally or

vertically.

Turn clockwise

to tighten.

Figure 8 — Adjust speaker and lock in place

6SI 26 and SI 28 Speakers • Speciﬁcations

Installation, cont’d

11. Repeat steps 1-10 for the second speaker.

12. When both speakers are in place, carefully pull enough

wire to reach up to the terminals at the back of the speaker

and strip the ends of the wire approximately 5/8" (15 mm),

for connection. . Twist the bared ends of each separate wire

so that they will hold ﬁrmly in the connector.

Twist the bared wire

Strip approx. 15 mm (5/8”)

Figure 9 — Strip the wire and twist the bared ends

13. Press down on the spring loaded terminals to open the

holes at the top. Observing the correct polarity, (,wire

to , terminal and .wire to . terminal) insert the

twisted wires into the relevant open holes (see ﬁgure 10)

and release the springs to secure. Push any loose wire

through the plate on the wall mount assembly and back

into the wall.

CDo not connect the speaker terminals to one

channel in parallel (together) with those of the other

channel.

Push down on the spring terminals at the

back of the speaker, and insert the wires.

Release the springs to secure.

INPUT

Extron

positive wire

negative

wire

Figure 10 — Insert wiring into the terminals

14. Turn on the audio source and any associated devices.

Follow the manufacturers instructions to adjust the source

and device settings as desired to get the optimum audio

output for your speaker application. If necessary, re-adjust

the angle of the speaker (repeat step 10) to get the best

audio area coverage.

SI 26 and SI 28 Speakers • Speciﬁcations

Speciﬁcations

Audio/acoustic and electrical

Speaker type................................... 2-way, indoor/outdoor surface mount

Frequency range............................ SI 26 70 Hz to 20 kHz, -10 dB, half space

SI 28 50 Hz to 20 kHz, -10 dB, half space

Power capacity .............................. SI 26 150 W continuous program

75 W continuous pink noise

SI 28 180 W continuous program

90 W continuous pink noise

Nominal sensitivity....................... 90 dB SPL, 1W, 1m, half space

Nominal impedance ..................... 8 ohms

Crossover frequency ..................... SI 26 2.3 kHz

SI 28 2.1 kHz

Woofer............................................. SI 26 6.5" (165 mm) polypropylene cone

SI 28 8.0" (203 mm) polypropylene cone

Tweeter ........................................... 1.0" (25 mm) aluminum dome

Overload protection...................... Full range power limiter, protecting the

tweeter, woofer, and crossover

Input connector ............................. 2 pin spring terminals

General

Package........................................... 2 speakers (1 pair)

Temperature/humidity Storage: -40 to +158 °F (-40 to +70° C) / 10% to 90%,

noncondensing

Operating: +32 to +122 °F (0 to +50° C) /

10% to 90%, noncondensing

Mounting........................................ Wall mount assembly with V-lock (patent

pending)

NWall mount assembly can be angled up to 20° upward,

35° downward, 30° to the left, and 30° to the right.

Enclosure type ............................... Plastic, trapezoidal, with metal grille and

bass reﬂex ports

Enclosure outer dimensions ........ SI 26: 13.0" H x 8.5" W x 6.75" D

(33.0 cm H x 21.6 cm W x 17.1 cm D)

SI 28: 16.5" H x 11.5" W x 8.6" D

(41.9 cm H x 29.2 cm W x 21.9 cm D)

Product weight .............................. SI 26 11 lbs (5 kg) each

SI 28 15 lbs (6.8 kg) each

Shipping weight ........................... SI 26 30 lbs (14 kg) per pair with

mounting kit package

SI 28 40 lbs (19 kg) per pair with

mounting kit package

Extron’s Warranty

Extron Electronics warrants this product against defects in materials and workmanship

for a period of five years from the date of purchase. In the event of malfunction during

the warranty period attributable directly to faulty workmanship and/or materials, Extron

Electronics will, at its option, repair or replace said products or components, to whatever

extent it shall deem necessary to restore said product to proper operating condition,

provided that it is returned within the warranty period, with proof of purchase and

description of malfunction to:

USA, Canada, South America, Europe, Africa, and the Middle East:

and Central America: Extron Electronics, Europe

Extron Electronics Beeldschermweg 6C

1001 East Ball Road 3821 AH Amersfoort

Anaheim, CA 92805, USA The Netherlands

Asia: Japan:

Extron Electronics, Asia Extron Electronics, Japan

135 Joo Seng Road, #04-01 Kyodo Building

PM Industrial Bldg. 16 Ichibancho

Singapore 368363 Chiyoda-ku, Tokyo 102-0082

Japan

This Limited Warranty does not apply if the fault has been caused by misuse, improper

handling care, electrical or mechanical abuse, abnormal operating conditions or non-

Extron authorized modification to the product.

If it has been determined that the product is defective, please call Extron and ask for an

Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400

(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This

will begin the repair process as quickly as possible.

Units must be returned insured, with shipping charges prepaid. If not insured, you

assume the risk of loss or damage during shipment. Returned units must include the

serial number and a description of the problem, as well as the name of the person to

contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect

to the product and its quality, performance, merchantability, or fitness for any particular

use. In no event will Extron Electronics be liable for direct, indirect, or consequential

damages resulting from any defect in this product even if Extron Electronics has been

advised of such damage

8SI 26 and SI 28 Speakers • Speciﬁcations

Speciﬁcations, cont'd

Figure 9 — Packaging for SI 26 and SI 28

Warranty......................................... 5 years parts and labor

N All nominal levels are at ±10%.

N Speciﬁcations are subject to change without notice.

Packaging information

PartNo.

XXX-XXX-01

Install 206W Ceiling Speaker

33-XXXX-01REV.

Thick Single Wall

Packing

Bottom Foam

Wall Mount

Assemblies

Speakers

Back Covers

Allen Hex Tool

Top Foam

Product Label

Altri manuali per SI 26

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extron electronics Altoparlanti

Extron electronics

Extron electronics SpeedMount SM 26 Manuale utente

Extron electronics

Extron electronics SB 33 A Series Manuale utente

Extron electronics

Extron electronics SI 26CT Manuale utente

Extron electronics

Extron electronics SI 28 Manuale utente

Extron electronics

Extron electronics SF 28PT Manuale utente

Extron electronics

Extron electronics SF 228T Manuale utente

Extron electronics

Extron electronics FF 120T Manuale utente

Extron electronics

Extron electronics SoundField XD SF 26CT LP Manuale utente

Extron electronics

Extron electronics SM 28 Manuale utente

Extron electronics

Extron electronics SI 28 Guida rapida

Extron electronics

Extron electronics BCK SF 26CT LP Manuale utente

Extron electronics

Extron electronics SM 26 Manuale utente

Extron electronics

Extron electronics DAK SF 26CT Manuale utente

Extron electronics

Extron electronics SF 26PT Manuale utente

Extron electronics

Extron electronics SM 28 Manuale utente

Extron electronics

Extron electronics BCK SF 3C LP Manuale utente

Extron electronics

Extron electronics SM 3 Manuale utente

Extron electronics

Extron electronics DAK SF 26CT Manuale utente

Extron electronics

Extron electronics SI 26W Manuale utente

Extron electronics

Extron electronics SI 26CT Manuale utente

Extron electronics

Extron electronics SI 3CT LP Manuale utente

Extron electronics

Extron electronics SI 3 System INTEGRATOR Manuale utente

Extron electronics

Extron electronics BCK SF 3CT LP Manuale utente

Extron electronics

Extron electronics SF 3C LP Manuale utente

Manuali Altoparlanti popolari di altre marche

argon audio

argon audio IE20 Manuale utente

Denon

Denon SC-N7 Manuale utente

Gemline

Gemline Ace 3952 Manuale utente

Focal

Focal ON WALL 300 Manuale di istruzioni

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuale utente

SoundLogic

SoundLogic BCCS-6/6395 Manuale utente

Peavey

Peavey DTH 218 Manuale utente

Avantree

Avantree Pluto Air Manuale utente

Morel

Morel Integra Series INTEGRA OVATION 4 Manuale utente

Oppo

Oppo SONICA Manuale utente

Bose

Bose SoundLink Wireless Music System Manuale utente

Rocksteady

Rocksteady Stadium Manuale utente

Bowers & Wilkins

Bowers & Wilkins 4 Manuale utente

Sonance

Sonance SONOS OUTDOOR Series Manuale utente

Electro-Voice

Electro-Voice EVID FM4.2 Manuale utente

Pioneer

Pioneer XW-HTD630 Manuale utente

Onn

Onn BWA16AA002 Manuale utente

HP GL313AA - USB Speakers PC Multimedia Manuale utente