Felix Storch 3.1 Single Manuale utente
Assembly manual for:
FELIX 3.1 Single
FELIX 3.1 Dual
copyright Information
This document contains proprietary information that is protected by copyright.
no part of this document may be photocopied, reproduced, or translated to another language with-
out the prior written consent of FELIXrobotics BV.
Felixrobotics BV
Zeemanlan 15, 3401 MV, IJsselstein, the Netherlands, Copyright © 2015 FELIXrobotics BV
FELIX 3.1
assembly manual
Before you start
Assembly Manual FELIX 3.1 V1
INDEX:
Description: Steps: Page:
Required tools 5
Frame 1 - 8 6
Z-axis 9 - 28 8
X-axis 29 - 41 11
Extruder 42 - 59 15
Y-axis and printbed 60 - 80 23
Handle 81 - 83 27
Electronics Box 84 - 92 28
Wiring 93 - 102 30
Display 103 - 113 34
BOM (Bill of Materials) 37
Assembly Manual FELIX 3.1 V1
Required tools:
Rubber hammer
Assembly Manual FELIX 3.1 V1 6
MODULE 1: FRAME 10-30 MINUTES
Tools:
Step 1 / 8
12x Bolt M8 x 20
2x Frameconnector
pro le 4
2pro le 1
Pro le:
1
423
Bolt M8 x 20
Frameconnector
!holes
!
Holes
Pro le 4
Pro le 1
3
!
160 mm
Pro le 4
!
hole
Assembly Manual FELIX 3.1 V1 7
42x Bolt M8 x 20
2x Frameconnector
2x pro le 2
5
160 mm
!Holes
Pro le 2
Pro le 2
62x Bolt M8 x 20
2x Frameconnector
1x pro le 3
Pro le 3
7
!Make sure everything is perpendicular and
aligned.
84x End cap square
1x End cap rectangle
The frame is now fi nished.
Pro le 4
Pro le 1
Assembly Manual FELIX 3.1 V1 8
MODULE 2: Z-AXIS 45-90 MINUTES Step 9 / 28
Tools:
94x CSK bolt M3x8
1x Motor
1x Z-axis motor bracket
Label end of the wire
with the letter: Z
Example mounting T-slots:
Cable orientation
!
10 2x M4 T-slot 11 2x Bolt M4x20
2x Small washer M4
!
7
Assembly Manual FELIX 3.1 V1 9
12
Make sure the plastic part
properly touches the frame! !
Don’t let the cart run off the rail!!
13 3x M4 T-slot
1x Hiwin lineair ball bearing set
HGW15CC1R300Z0
3x Bolt M4x20
14
!
15 1x Z-axis lift part
1x Hexagon nut
10mm 10mm between rail
and plastic!
12mm from side rail
to side frame!
!
Assembly Manual FELIX 3.1 V1 10
16 2x Bolt M4x40
2x Locknut M4 17
Put the bolts in place in
the plastic part by pulling
the bolts.
19 2x Bolt M4x25
4x Bearing
2x Small washer M4
!
18
Remove the bolts M4x40
!
20
7
21 4x Bolt M5x16
4x Small washer M5
Assembly Manual FELIX 3.1 V1 11
23 4x CSK bolt M3x8
1x Motor
!
1x pulley
1x Set screw M3x6
Label end of the wire with the letter: Y
Wire orientation!
24
Distance pulley to motor face = 1-2mm
!
25 1x Spindle
26 1x Set screw M3x6
!
Hole for set screw
27 1x Z-axis limitswitch vane
1x Bolt M4x25
1x Square nut M4
1x Selfl ocking nut M4
28 1x Bolt M4x20
1x Small washer M4
1x M4 t-slot
The Z-axis is
fi nished.
Put some grease
on the spindle,
for example ball
bearing grease.
Indice
Altri manuali Felix Storch Stampante 3D
Felix Storch
Felix Storch Food 1.5 Manuale utente
Felix Storch
Felix Storch Pro 3 Manuale utente
Felix Storch
Felix Storch Pro BIOprinter Manuale utente
Felix Storch
Felix Storch FELIXFOOD 3D Manuale utente
Felix Storch
Felix Storch Pro 3 Manuale utente
Felix Storch
Felix Storch Pro L Series Manuale utente
Felix Storch
Felix Storch 2.0 Manuale utente
Felix Storch
Felix Storch Pro L Manuale utente
Felix Storch
Felix Storch Pro 3 Manuale utente
Felix Storch
Felix Storch Tec 4.0 to Tec 4.1 Upgrade Kit Guida rapida
