Felix Storch Pro Series Manuale utente

How to replace a hot-end nozzle

29 January

2021

Revision 2

FELIX Pro series

How to replace a hot-end nozzle

29 January 2021

FELIX Pro

www.FELIXprinters.com

Pro series

1Introduction

This tutorial explains how to exchange a hot-end nozzle properly. A replacement can be needed, when the

tip is completely clogged or when it is required to use a different nozzle size, also see the Cold pull method

this can safe most clogged nozzles.

2Tools

The tools you need to replace the tip of the FELIX Pro nozzle:

•Allen key 1.5

•(open-end) Wrench 12

•(closed-end) Wrench 7

3Take the hot-end out of the machine

Warning: When filament is still loaded into the FELIX Pro , the hot-end

cannot be removed

The first step is to take the hot-end out of the Pro. Before this is possible, the filament that is in the machine

should be removed. When the filament is removed, let the hot-end fully cool down.

Turn off the FELIX Pro

Disconnect the cable that connects the hot-end to the mainboard. Carefully pull the connector away from

the socket.

1. Pull off edge connector of corresponding print head, do NOT pull the wires, there is also a small hook on

the fan duct to which the cable is fixed take it off this hook first.

2. Open the cover in front.

3. Rotate slightly to right

4. and Then pull out print-head

How to replace a hot-end nozzle

29 January 2021

FELIX Pro

www.FELIXprinters.com

Pro series

4Remove the screws in the hot-end

Warning: only hold the hot-end by the barrel. Do not put pressure on the outside mechanism. This part is

calibrated at the FELIXprinters factory - any changes in the calibration will influence the print results.

Hold the hot-end by the barrel and use the Allen Key 1.5 to remove the two screws located close to the tip

of the hot-end. After this you can take out the heater themistor cartridge

How to replace a hot-end nozzle

29 January 2021

FELIX Pro

www.FELIXprinters.com

Pro series

5Remove the tip of the hot-end

Place the open Wrench 12 around the body of the hot-end to be able to hold it firmly. Use a closed Wrench

7 to remove the tip of the hot-end.

How to replace a hot-end nozzle

29 January 2021

FELIX Pro

www.FELIXprinters.com

Pro series

6Place the new tip

Now that the old tip is removed, place the new tip and lock it firmly into its place.

Place the new nozzle and turn it in by hand.

To prevent the nozzle from leaking it’s best to heat up the hot end with a hot airgun or a

lighter and then tighten it a little more after that, be careful you don’t burn yourself

though. If you still see some leaking you can tighten it in the machine while it’s on

temperature for the material you want to print.

How to replace a hot-end nozzle

29 January 2021

FELIX Pro

www.FELIXprinters.com

Pro series

7Reconnect the hot-end to its cables

Put the cables into their slots again and carefully lock them with the small screws. Check that the cable

goes to the right side away from the handle.

Do not put too much pressure on the thermistor and heater but just

enough to feel the cables are locked in their places.

8Put the hot-end back into its slot

Firmly push the hot-end into its slot. Make sure it is pushed in all the way to the back. Push till you hear a

‘click’ sound. This means the hot-end is in the correct position.

5. Pull off edge connector of corresponding print head, do NOT pull the wires, there is also a small hook on

the fan duct to which the cable is fixed take it off this hook first.

6. Open the cover in front.

7. Rotate slightly to right

8. and Then pull out print-head

9. Reverse the assembly of the hot-end into the extruder assembly. Do not forget to close the lid.

IMPORTANT: Ensure the hot-end wires make the bend as shown in picture above

10. Please do the following two extruder calibrations, if you wish to properly print with dual head.

-Z-height calibration

-XY calibration

How to replace a hot-end nozzle

29 January 2021

FELIX Pro

www.FELIXprinters.com

Pro series

You are now be able to use the FELIX Pro again

If you are unable to continue or have any questions, you can check at the support section of our website or

you can contact us directly:

Website: www.felixprinters.com/support

Email: support@felixprinters.com

Telephone: +31 (0)30 30 31 387

Address: Zeemanlaan 15, 3401MV IJsselstein, The Netherlands

Kind regards,

FELIXprinters

Indice

Altri manuali Felix Storch Stampante 3D

Felix Storch

Felix Storch Pro BIOprinter Manuale utente

Felix Storch

Felix Storch Pro 3 Manuale utente

Felix Storch

Felix Storch Tec 4.0 to Tec 4.1 Upgrade Kit Guida rapida

Felix Storch

Felix Storch 2.0 Manuale utente

Felix Storch

Felix Storch Pro L Series Manuale utente

Felix Storch

Felix Storch Pro L Series Manuale utente

Felix Storch

Felix Storch Pro 3 Manuale utente

Felix Storch

Felix Storch 3.2 Manuale utente

Felix Storch

Felix Storch Pro L Manuale utente

Felix Storch

Felix Storch 3.1 Single Manuale utente

Felix Storch

Felix Storch Pro 3 Manuale utente

Felix Storch

Felix Storch Pro 3 L Manuale utente

Felix Storch

Felix Storch FELIXFOOD 3D Manuale utente

Felix Storch

Felix Storch Food 1.5 Manuale utente

Felix Storch

Felix Storch Pro L Series Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente