Felix Storch Pro L Manuale utente

Quick Start Guide

FELIX Pro L / XL

www.FELIXprinters.com/support

[email protected]

Zeemanlaan 15

3401MV IJsselstein

The Netherlands

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 1

1Safety

General safety

-Keep children under the age of 14 out of reach of the printer

-FELIXprinters are only suitable for professional use.

Considerations when in operation.

-Don’t leave the printer unattended, before making sure the

first layer is printed properly

-Don’t lean on the printer.

-Be careful with long hair and wide clothes.

-Don’t transport the printer.

-Make sure all moving parts can move without any obstructions.

-Don’t remove any objects from the hot plate while printing.

-Caution with any moving parts that move in the X, Y and Z

direction. Moving parts can have a pinching hazard.

Electronic safety

-Only use the power supplies and cables supplied by FELIXprinters.

Always turn off and unplug the printer before performing

maintenance or modifications.

-The power supply meets all CE mark regulations and is protected

against short-circuit, overload, over voltage and over

temperature.

Printer placement

-Place the FELIXprinter on a stable surface.

-Place the printer out of reach of children. Use the FELIXprinter in a

dry environment at room temperature.

Ventilate

-Good ventilation while printing is advised. When printing ABS,

small concentrations of styrene vapor can be released. This can

(in some cases) cause headaches, fatigue, dizziness, confusion,

drowsiness, malaise, difficulty in concentrating, and a feeling of

intoxication.

-We recommend using filament types shown on the

FELIXprinters website. Examples PLA, PETG, ABS-X, Glassbend

etc. Other types may be toxic; please follow instructions from

the filament supplier.

Caution with heater elements

-There is a potential risk of burn, as the print head can reach

temperatures of up to 275°C and the heated bed of up to 120°C.

-Don’t place objects on the heated bed, not even when the

printer is turned off.

-Always let the printer cool down for at least 5 minutes before

doing maintenance or modifications.

-Never try to print without a buildplate in the machine, this can

cause damage to the machine and heated bed.

 
Quick Start Guide FELIX Pro L / XL 
 
10 December 2019 
Page 2
2Introduction 
Thank you for choosing FELIXprinters! 
It is highly recommended to at least read this manual. It explains in short how to make your first print and contains important 
information to operate the printer properly. 
Kind regards, FELIXprinters 
3Contents 
1SAFETY .....................................................................................................................1 
2INTRODUCTION ......................................................................................................2 
3CONTENTS ...............................................................................................................2 
4PRINTER SPECIFICATIONS......................................................................................1 
5FELIX PRO L / XL AT A GLANCE..............................................................................1 
6WHAT’S IN THE BOX?..............................................................................................2 
 INSTALLING TEFLON TUBES ..................................................................................... 3 
 POWER ON.............................................................................................................. 4 
7DISPLAY OVERVIEW ................................................................................................5 
 CALIBRATION. ............................................FOUT!BLADWIJZER NIET GEDEFINIEERD.
 ERRORS DURING LEVELING .................................................................................... 11 
8Z CALIBRATION .....................................................................................................12 
 ERRORS................................................................................................................. 13 
9XY CALIBRATION ..................................................................................................15 
 LOAD FILAMENT ................................................................................................... 17 
 CLEAN THE PRINT SURFACE ................................................................................... 18 
10 PRINTING ........................................................................................................ 19 
11 PRINT AND CONTROL PRINTER VIA WIFI OR LAN...................................... 20 
 CONNECTING TO WIFI OR WLAN................................................................... 20 
 REMOTE CONTROL ......................................................................................... 20 
 PRINT VIA WEB INTERFACE. ............................................................................. 24 
12 POWER LOSS RECOVERY................................................................................ 26 
13 TIPS AND TRICKS ............................................................................................ 29 
 FLEXIBLE FILAMENTS ...................................................................................... 29 
MAINTENANCE ................................................................................................................. 30 
 HOW TO MAINTAIN/EXCHANGE HOT-ENDS...................................................... 30 
 DUST CLEANERS ............................................................................................. 33 
 MOTION SYSTEM............................................................................................ 33 
14 DISPLAY MESSAGES........................................................................................ 34 

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 1

4Printer specifications

System specifications

-Printer dimensions (L, W, H) 600 x 666 x 776 mm (XL)

-Printer dimensions (L, W, H) 906 x 666 x 966 mm (L)

-Weight 65 kg (L), 80 kg (XL)

-Power requirements: 220 V

Capabilities

-Build volume (L, W, H) 300 x 400 x 400 mm (L)

-Build volume (L, W, H) 600 x 400 x 600 mm (XL)

-Layer height range 0.05 - 0.25 mm (L) 0.05 –0.35 (XL)

-Bed temperature: max. 110 °C

-Flex plate

-Software bed leveling

-Automatic nozzle calibrations

Extruders

-Diameter nozzle: 0.35 mm (L) 0.5 (XL) (optional 0.5 and

0.7mm)

-Nozzle temperature: max. 275 °C

-Full metal hot-ends

-Filament flow detection

Interface

-Capacitive Touchscreen, with embedded 1.2 Ghz quad

core processor.

-Print server (Repetier-Server)

-Webcam

-Print file management

-16GB memory

Print materials

-Open source 1.75 mm filaments

-Tolerance: ± 0.15 mm

-PLA, PET(G), Flex, ABS-X, PVA, Wood, Glass

Connectivity

-USB flash drive

-WIFI

-Wired Ethernet

Software

-Simplify3D

-Open source Repetier-Host for FELIXprinters.

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 1

5FELIX Pro L / XL at a glance

Display unit

Extruder

Heated bed

Filament roll

Power switch

Power plug

LAN port

Filament guide

USB port

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 2

6What’s in the box?

1x Tweezers

1x Spatula

1x Power cable

3x Bed calibration tool

1x MicroSD card +

USB reader

1x Allen key set

2x Teflon tubes

1x Premium PLA roll

1x Wrench 14mm

Recommended tools:

NB: The box could contain extra materials like filament you have ordered.

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 3

Installing Teflon tubes

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 4

Power on

1. Insert the power cable.

2. Flip ON the UPS (optional) to activate power dip/loss recovery function. Battery will start to charge if not

fully charged already. For this to function properly, the battery needs to be charged.

NOTE: When this switch is on, the battery will charge itself until full even when the power switch is turned

off.

3. Flip ON the power switch.

-The lights of the print-head turn on immediately

-The screen boots up in about 40 seconds.

Power switch

UPS Switch

(power dip/loss recovery)

Ethernet port

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 5

7Display Overview

Shutdown button: To properly shutdown the printer. First press the shutdown button before turning the power

switch off. This ensures proper shutting down of the operating system on the Display unit.

Quick Start Guide FELIX Pro L / XL

10 December 2019

Page 6

8Printer calibration

For 3d printing, the first layer is the most important

layer. It is the basis of a print job (which can take

more than 70 hours in some cases). An improperly

printed first layer is mostly the cause of a failed

print. With the automatic calibration features

properly executed, the chance of failure will be

minimized. Also see the QuickStart guide for more

in depth calibration.

The calibration mechanism is dependent upon the

following features on the printer.

-The probe sensor in each hot-end.

-The leveling software.

So, when one of the above two systems is not

working properly, the printer will not be able to

calibrate.

What does the calibration do?

For the FELIX Pro L/XL to properly operate the calibrations

described in this chapter need to be performed.

8.1.1 Software based leveling the build plate.

To ensure the distance between the bed and the nozzles is the

same over the whole build plate. This is done automatically.

When to do this calibration?

-When changing to a new bed.

-When the first layer is not sticking to the bed

-When you see that the lines on the first layer,

significantly differ in thickness from one side to the

other side of the build plate.

-After transporting the printer.

When the auto bed leveling routine is started. The following

steps are performed.

1. The hot-ends heat up to 185 ˚C

2. The currently active extruder will touch the bed at a

couple of points.

3. The bed leveling software turn the Z spindles to make

the bed level. (Level in this case means that the

distance between the build plate and the hot-end is the

same over the whole bed surface).

4. After this the software will compensate the first couple

of layers to ensure a proper first layer.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Felix Storch Stampante 3D

Felix Storch

Felix Storch Food 1.5 Manuale utente

Felix Storch

Felix Storch Pro 3 Manuale utente

Felix Storch

Felix Storch Tec 4.0 to Tec 4.1 Upgrade Kit Guida rapida

Felix Storch

Felix Storch Pro L Series Manuale utente

Felix Storch

Felix Storch Pro 3 L Manuale utente

Felix Storch

Felix Storch Pro L Series Manuale utente

Felix Storch

Felix Storch 3.2 Manuale utente

Felix Storch

Felix Storch Pro BIOprinter Manuale utente

Felix Storch

Felix Storch Pro Series Manuale utente

Felix Storch

Felix Storch Pro 3 Manuale utente

Felix Storch

Felix Storch Pro L Series Manuale utente

Felix Storch

Felix Storch 2.0 Manuale utente

Felix Storch

Felix Storch FELIXFOOD 3D Manuale utente

Felix Storch

Felix Storch 3.1 Single Manuale utente

Felix Storch

Felix Storch Pro 3 Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente