Flashforge Creator Pro Manuale utente

This guide only applies to Creator Pro 3D printer of Flashforge

Quick Start Guide

Caution 1. Do not remove the wrapping around the nozzle.

2. If print with PLA filament, please remove the lid and open the front door to ventilate for a better printing performance.

Warning 1. High Temperature! Plate may have been heated before; make sure it has cooled down before inner operation.

2. Loose clothes, jewelry and long hair can be caught in moving parts. Please keep away from them.

SZ10-EN-002

Creator Pro

User Guide The User Guide is in SD card.

Kit Contents

顺时针旋转螺母

升高打印平台。

即减少平台与喷嘴之间

的距离。

逆时针旋转螺母

降低打印平台。

即增加平台与喷嘴之间

的距离。

调整平台支架下方的螺母，直至纸片在喷嘴与平台间的

运动感受到轻微的阻力。

打印平台调节专用

扫描二维码，观看调平指导视频！

3D Printer

Do Not Touch 请勿触摸

CAUTION

注意 1.Extruder hot during operation.

使用过程中喷头会发热。

2.Heating plate hot during operation. Allow surface to cool before servicing.

使用过程中加热平台会发热，待平台表面冷却后再操作。

Lid Power Cable USB Cable

Filament Spool X 2

SD Card Build Tape X 2Spool Holder X 2 Quick Start Guide

Filament Guide Tube X 2

Leveling Card

Tool bag:

(Allen Wrench X 3 / Leveling knob X 1 / M3X8 Bolt X 2 / PTFE Tube X 2)

Extruder’s accessory kit

(M3X8 BoltX2 / M3X6 Bolt / Turbofan baffle)

Tool Bag

Extruder’s

Accessory Kit

Getting to Know Your Creator Pro

14 15

Extruder

1. Z-Axis Guide Rod

16. X-Axis Guide Rod

14. Turbofan Baffle

21. Reset Button

8. SD Card Input

22. USB Input

19. Power Switch

20. Power Input

3. Slot

7. Leveling Knob

5. Build Plate

9. LCD Panel

10. Buttons

12. Spring Presser

17. Filament Guide Tube Buckle

18. Spool Holder

23. Quadrangular Opening

2. Extruder Cable Bunch

4. Y-Axis Guide Rod

6. Build Platform

13. Turbofan

11. Cooling Fan

15. Nozzle

Unpacking

1. Open the carton and then take the top

foam sheet out.

4. Remove the packing bag. And then

remove the tape and plastic wrap for

protecting the front door.

2. Within the PE foam sheet are lying two

filament guide tubes, one piece of build

tape, one piece of Flashforge leveling

card and one Quick Start Guide.

3. Firmly grasp the two side handles of

Flashforge Creator Pro. Lift it out from the

carton and place it on a stable surface.

5. The Flashforge Creator Pro and its

accessories shall be displayed in front

of you.

6. Take the dual extruder out and place it

onto a clean ground.

7. Take the accessory foam container out, within which are lying a power cable,

a USB cable, two spool holders, a SD card, a tool bag and a extruder’s accessory kit.

8. Slide the X-axis Rods to the very back.

9. Take the lid together with tworolls of

filament out from the printer.

10. Take the two rolls of filamentout from

the lid.

11. Take the side protective foam sheets

from the printer.

1. Place two anterior angles the corresponding

front slots.

2. Squeeze slightly the two relief angles and

place them to the corresponding rear slots.

Anterior Angle

Relief Angle

13. Take the bottom protective foam from

 the printer.

14. Congratulations! You’ve finished the

 unpacking process. (Tip: Save your

Flashforge Creator Pro packaging for

future transportation and storage. )

12. Elevate the build plate to its limit.

Anterior Angle

Installation and Dismantlement

Hardware Assembly

Extruder Assembly

(1) Place the dual extruder on the extruder seat.

(As shown in the left picture)

(2) Take the M2.5 Allen Wrench from the tool bag and two

M3*8 bolts(longer ones) from the extruder’s accessory kit.

(3) Adjust the extruder location to align the bolt holes.

(4) Secure the extruder onto the extruder seat by screwing

the M3*8 bolts in.

Bolt Hole Bolt Hole

Bolt Hole

M3*8 bolts

X-Axis Guide Rod

(1)

(2)

Turbofan Baffle Assembly

(1) Use the M2.5 Allen Wrench to remove two turbofan bolts.

(As shown in the picture above)

(2) Take the turbofan baffle from the extruder’s accessory kit.

(3) Install the turbofan baffle to the turbofan.

(As shown in the top-right picture)

Caution: During installation, please take care of the

turbofan cable.

Bolt Removal

(1) Place the turbofan sub-assembly besides the turbofan seat.

(2) Insert the bump on the turbofan seat to the turbofan sub-assembly.

(3) Screw the two bolts in.

(4) Take a M3*6 bolt from the extruder’s assembly kit and complete

installation according to the instruction below.

Turbofan Seat

Bolt Mounting

Bolt MountingBolt Mounting

M3X6 Bolt Mounting

Bolt Mounting

Align the bump on the turbofan

seat to the hole in turbofan

sub-assembly.

(1) (2)

(3)

(4)

Filament Guide Tube and Filament Installation

(1) To install a spool holder, level it and insert the end into

the corresponding opening.

(2) Turn down the spool holder to make the holder bottom

cleave to the printer back.

(3) Take a roll of ABS filament, then squeeze the spool

holder top and mount the filament spool to the holder.

(4) Lock the filament guide tube with R-shape buckles.

Please refer to the next page

for the right method of

filament mounting

Filament Guide

Tube Buckle

Altri manuali per Creator Pro

Indice

Altri manuali Flashforge Stampante 3D

Flashforge

Flashforge Guider 3 Plus Manuale utente

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge Creator Pro Manuale utente

Flashforge

Flashforge Guinder II Manuale utente

Flashforge

Flashforge ADVENTURER 3 Manuale utente

Flashforge

Flashforge CN/EN-A01 Manuale utente

Flashforge

Flashforge Guider II Manuale utente

Flashforge

Flashforge EN-A01 Manuale utente

Flashforge

Flashforge Foto 13.3 Manuale utente

Flashforge

Flashforge Adventurer3 Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Adventurer 4 Manuale utente

Flashforge

Flashforge Creator Pro Manuale utente

Flashforge

Flashforge DREAMER Manuale utente

Flashforge

Flashforge Inventor 2 Manuale utente

Flashforge

Flashforge Creator3 Manuale utente

Flashforge

Flashforge Inventor Manuale utente

Flashforge

Flashforge Adventurer 4 Pro Manuale utente

Flashforge

Flashforge Finder Istruzioni di installazione e manutenzione

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge DREAMER Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Hunter Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente