FLIR CM55 Manuale utente
GETTING STARTED
FLIR MODEL CM55 and MODEL CM57
FLEX CLAMP METERS with Bluetooth®
FLIR CM55_CM57 - GETTING STARTED Document Identifier: CM55_CM57-QS-en-US_AC
CM55_CM57 - GETTING STARTED - EN
USER GUIDE LOCATION: The detailed User Guide is located in the product packaging and on the support.flir.com web
site (download tab). Please read the entire User Guide to gain a thorough understanding of the meter before use.
Register for Extended Warranty and Product Updates at www.flir.com/testwarranty
Quick Overview
Press and hold to power ON or OFF. Install or replace
batteries in rear compartment if meter does not power up.
Meter switches OFF automatically after 10 mins of inactivity.
Current Measurements are covered on the next page.
For the descriptive diagram at right, see the descriptions below:
1. Work Lights
2. Flexible Current Clamp Coil
3. Display
4. INRUSH / REC (Record) button
5. Power / Work Light button
6. RANGE / SEND button
7. HOLD / Start-Stop Record / Bluetooth® button
8. Clamp Lock mechanism
Note: Battery compartment on rear of meter
When powered, press to turn Work Lights ON or OFF.
Press HOLD to freeze displayed readings.
Press RANGE for Manual Ranging (Auto Range is default).
Press INRUSH for inrush current mode (refer to User Guide).
Press and hold REC to record readings at 1 min. intervals.
Press to Start/Stop recording (in REC mode only).
Press and hold to activate Bluetooth®(real time readings will
now be available to Bluetooth®paired devices).
Press and hold SEND to transmit bulk stored readings via
Bluetooth®(refer to User Guide for in-depth information).
Button Overview
Momentary press to access INRUSH mode
Press and hold to access the Record Memory mode (REC)
Momentary presses step through the ranges manually
Press and hold while in manual range mode to return to Auto range
Press and hold to Send data via Bluetooth® (refer to User Guide for in-depth information)
Momentary press to access the Data Hold mode
Press and hold to activate/deactivate Bluetooth® communication
While in Record mode, momentary press to Pause/Resume recording
Press and hold to switch power ON/OFF
When powered, press to activate/deactivate work lights
FLIR CM55_CM57 - GETTING STARTED Document Identifier: CM55_CM57-QS-en-US_AC
Positioning Conductor in Center of Clamp Jaw
Display Icons
Bluetooth® Communication
Display Hold
Amperes (Current)
Battery status
Inrush Current
Auto Power Off (APO)
Bulk Data Transmission
Memory (Recording) Mode
Auto Range mode
AC Current Measurements
WARNING: Ensure that power to the device under test is OFF before starting this procedure. Switch power to the device
under test ON only after the clamp has been safely attached to the device under test.
CAUTION: Do not move fingers above the LCD at any time during a test.
1. Switch the meter OFF and switch power to the device under test OFF.
2. Turn the clamp lock (1) counter-clockwise to release the flexible clamp (2).
3. Fully enclose only one conductor of the device under test with the flexible clamp
probe (see diagram below for Correct and Incorrect usage).
4. Re-secure the clamp lock (1) after clamping around a single conductor.
5. Do not attempt to measure current higher than the specified current limit.
6. Switch the meter ON and then switch power to the device under test ON. Never
move fingers above the display area when running a test.
7. Read the current value in the display; ‘OL’ will display if the measured signal
exceeds the range. The meter defaults to the Auto Range mode; the Auto Range
icon is visible on the display. The meter will automatically select the appropriate
range when in Auto Range mode.
8. To manually select the range, use the RANGE button to step through the available ranges (30.00A / 300.0A /
3000A).
Copyright ©2015-2018 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form.
www.flir.com
Unlock/Lock Clamp Jaw
FLIR CM55_CM57 - GETTING STARTED Document Identifier: CM55_CM57-QS-en-US_AC
Corporate Headquarters
FLIR Systems, Inc.
2770 SW Parkway Avenue
Wilsonville, OR 97070
USA
Telephone: +1 503-498-3547
Customer Support
Technical Support Website http://support.flir.com
Customer Support Telephone +1 855-499-3662 (toll free)
Publication Identification No.: CM55_CM57-QS-en-US
Release version: AC
Release Date: 2018 September
Language: en-US
Altri manuali per CM55
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali FLIR Strumento di misura
FLIR
FLIR EXTECH INSTRUMENTS PQ3450 Manuale utente
FLIR
FLIR Extech Instruments EX840 Manuale utente
FLIR
FLIR Imaging Moisture Meter Plus IGM MR176 Manuale utente
FLIR
FLIR VS80 KIT Manuale utente
FLIR
FLIR VS80A2-45-1RM Manuale utente
FLIR
FLIR EXTECH HDV-TX1 Dimensioni
FLIR
FLIR Extech Instruments MA150 Manuale utente
FLIR
FLIR VS80C10-25RM Manuale utente
FLIR
FLIR Extech Instruments PQ34-2 Manuale utente
FLIR
FLIR MR265 Manuale utente
FLIR
FLIR MR77 Manuale utente
FLIR
FLIR CM275 Manuale utente
FLIR
FLIR MR160 Manuale utente
FLIR
FLIR Extech 380947 Manuale utente
FLIR
FLIR EXTECH SDL310 Manuale utente
FLIR
FLIR Si124 Manuale utente
FLIR
FLIR Extech Instruments EN300 Manuale utente
FLIR
FLIR identiFINDER R200 Manuale utente
FLIR
FLIR MR55 Manuale utente
FLIR
FLIR TA50 Manuale utente
