FLIR VS80 KIT Manuale utente
Quick Start
VS80 KIT
High Performance Videoscope and
Camera Probe
Quick Start (en)
INTRODUCTION
The VS80 kit consists of the main display unit, a camera probe, and
accessories. To obtain the comprehensive user manual, additional
quick start translations, firmware updates, and customer support,
see the Support section. Please upgrade the firmware before use
for optimal performance and camera compatibility.
The numbers in parenthesis, below, refer to the items listed in the
Product Description section.
QUICK STEPS
1. Insert micro SD card in slot located in side compartment (19).
2. Connect the camera probe (16):
3. Remove the camera’s protective lens cap.
4. Long press the power button (9), the FLIR logo will appear.
5. The camera image will then appear (14) with touch-screen
icons (12) bordering the image.
6. For the IR camera only, the dot on the probe head indicates the
top of the image, as shown:
7. If the battery icon (15) indicates a low charge, connect the sup-
plied AC adapter to the USB port at the top of the display unit
(17) and to an AC power source (100 to 240 VAC, 50/60 Hz).
8. The status LED (1) is blue when power is on (charger not con-
nected); green when charging with power off; cyan (light blue)
when charging with power on; no light when fully charged (with
charger attached).
9. Long press the power button (9) to switch off the VS80.
#NAS100100; r. AC/83794/84876; en-US 1
PRODUCT DESCRIPTION
1. Power status LED
2. Image capture button
3. Video recording start/stop button
4. 1. Full screen view button; 2. Disconnect Wi-Fi
5. Zoom in (navigate upward in touch-screen menus)
6. Zoom out (navigate downward in touch-screen menus)
7. Decrease brightness (move left in touch-screen menus)
8. Increase brightness (move right in touch screen menus)
9. Long press to power on/off. Short press to return from a menu
10. Settings menu button
11. Image/video gallery button
12. Touch screen icons
13. Temperature scale (IR only)
14. Camera images and menus
15. Battery status icon
16. Probe connection
17. PC interface/charger USB-C port
18. Neck and hand strap fasteners
19. Compartment for reset button, SD card, HDMI port
20. Microphone connector (3.5 mm)
Tilt stand, tripod mount (back of unit), and sun visor are not
pictured.
#NAS100100; r. AC/83794/84876; en-US 2
SETTINGS MENU
Press the Settings button to open or close the menu. The menu
has two pages, tap the up/down (∆ ∇) touch-screen arrows to scroll.
Tap an item to open it or to enable/disable it.
Menu items are briefly described below. For complete information,
please refer to the online user manual.
Wi-Fi Switch Wi-Fi on/off, set password (settings
icon), and view the SSID.
DISPLAY GRID Enable/disable the display measurement grid.
Digital cameras only
TIMESTAMP Enable to include date and time with recorded
images and video.
EXTERNAL MICROPHONE Enable microphone to record voice-overs on-
to video.
USB CARD READER Connect to a PC via USB to share images/
video and to update firmware (INFO menu).
SD CARD View memory status, format card, and delete
all images/video.
IMAGE Set display brightness, contrast, and sharp-
ness. Digital cameras only
MEASUREMENT
PARAMETERS
Set emissivity, reflected temperature, and
temperature units. IR camera only
AUTO POWER OFF Disable or set to 5, 10, 20, or 30 minutes.
DATE / TIME Set and format the calendar clock.
LANGUAGE Select local language.
RECORDING QUALITY
(VIDEO)
Set to Normal (1 M bits/s) or High Quality (2
M bits/s). Digital cameras only
PROBE SELECTION Select the probe that you are using from the
list. Digital cameras only
#NAS100100; r. AC/83794/84876; en-US 3
INFO View firmware version, upgrade firmware, and
revert settings to factory default.
ASPECT RATIO IR camera only. Toggle 4:3 and 16:9 display
formats.
DIGITAL CAMERA TOUCH SCREEN ICONS
Tap an icon to enable/disable it or to open its submenu. Refer to the
probe’s user manual for more information.
Switch the exposure com-
pensation filter on/off
(brightens dark areas).
Switch dust elimination filter
on/off. For use with mirror
accessories and dual cam-
era model.
Switch worklight on/off.
Forward/side view split
screen. For use with mirror
accessories and dual
cameras.
Switch the mirror image
on/off.
Change the direction of the
worklight (side/forward)
when using mirror accesso-
ries or dual camera.
Opens the image gallery.
Select an image to com-
pare with the live image
on a split-screen.
Switch the image negative
on/off.
Rotate image clockwise
(90°, 180°, 270°). Set the white balance.
IR CAMERA TOUCH SCREEN ICONS
Tap an icon to open its submenu. See the probe user manual for
more information.
Rotate image clockwise (90°, 180°, 270°) or view mirror image.
Select color palette (Iron, Rainbow, Gray) or alarm mode (Above
alarm, Below alarm).
Tap to open the Measurement submenu for Center Spot, Cold Spot,
Hot Spot, and No Measurement modes, explained below.
#NAS100100; r. AC/83794/84876; en-US 4
Center spot: Temperature of spot is displayed on upper left.
The coldest (cyan cross-hairs) or hottest (red cross-hairs) spot is
targeted in the boxed region of the image. The spot temperature is
shown on the upper left side of the display.
Tap and drag the box to move it, use the navigation buttons (up [5],
down [6], left [7], right [8]) to re-size it, or pinch/stretch the box with
two fingers to narrow or widen it.
No Measurements: Temperature is not measured.
Temperature Scale. Use Auto (A) in normal operation; Use Manual
(M) to limit the temperature range, based on the temperature of the
targeted spot.
Measurement parameters: Set emissivity, reflected temperature,
and temperature units.
ABOVE AND BELOW ALARMS (IR CAMERA)
To set an alarm, tap the palette icon and select the Above or
the Below alarm.
In Above alarm mode, the camera will apply a red color to all parts
of the image with a temperature above the alarm set point. In Below
alarm mode, the camera will apply a blue color to all parts of the im-
age with a temperature below the alarm set point.
Tap and drag the color bar graph to adjust the set point.
CUSTOMER SUPPORT
The FLIR support site, address below, is your resource for obtaining
firmware upgrade files, latest versions of user manuals, customer
service, and other product and accessory information.
https://support.flir.com
Three-Year Limited Warranty
This product is protected by FLIR’s 3-Year Limited Warranty. Visit
www.flir.com/testwarranty to read the 3-Year Limited Warranty
document.
#NAS100100; r. AC/83794/84876; en-US 5
last page
Publ. No.: NAS100100
Release: AC
Commit: 83794
Head: 84876
Language: en-US
Modified: 2022-03-08
Formatted: 2022-05-06
Website
http://www.flir.com
Customer support
http://support.flir.com
Copyright
© 2022, FLIR Systems, Inc. All rights reserved worldwide.
Disclaimer
Specifications subject to change without further notice. Models and accessories
subject to regional market considerations. License procedures may apply.
Products described herein may be subject to US Export Regulations. Please
Quick Start
Indice
Altri manuali FLIR Strumento di misura
FLIR
FLIR Extech Instruments RH520A Manuale utente
FLIR
FLIR CM174 C Manuale utente
FLIR
FLIR MSX MR277 Manuale utente
FLIR
FLIR Extech EX612 Manuale utente
FLIR
FLIR MR277 Manuale utente
FLIR
FLIR CM85 Manuale utente
FLIR
FLIR CM78 Manuale utente
FLIR
FLIR EXTECH HDV-WTX2 Dimensioni
FLIR
FLIR CM57-2 Manuale utente
FLIR
FLIR CM174 Manuale utente
FLIR
FLIR EXTECH INSTRUMENTS PQ34-12 Manuale utente
FLIR
FLIR MR55 Manuale utente
FLIR
FLIR CM174 Manuale utente
FLIR
FLIR MR7 Manuale utente
FLIR
FLIR Extech Instruments RH520A-240 Manuale utente
FLIR
FLIR Extech Instruments 380193 Manuale utente
FLIR
FLIR EXTECH HDV-WTX1 Manuale utente
FLIR
FLIR Extech 380926 Manuale utente
FLIR
FLIR identiFINDER R200 Manuale utente
FLIR
FLIR EXTECH SDL310 Manuale utente
