Futech DISTY 40R Manuale utente

USER

MANUAL

202.40R DISTY 40R

202.60G DISTY 60G

202.80R DISTY 80R

EN ENGLISH

Manual

in your language?

Check the back cover

OVERVIEW

CASE

1 Screen

2 Measure - ON button

3 Function - Back button

4 Beep - Unit button

5 Addition/Subtraction – Next button

6 Reference point – Timer button

7 Clear – OFF button

8 Memory – Save button

SCREEN

a Battery indicator

b Function indicator

c Angle

d Maximum

e Minimum

f Major display

g Auxiliary display, line 1

h Auxiliary display, line 2

i Auxiliary display, line 3

SAFETY & WARRANTY

Read the complete safety and warranty instruc-

tions provided together with the device before

using.

While the product is in operation, be careful not

to expose your eyes to the emitting laser beam.

LASER RADIATION, Class 2.

Do not stare into beam.

Do not disassemble the tool. There are no user

serviceable parts inside. Do not modify the tool

in any way. Modifying the tool may result in haz-

ardous Laser Radiation Exposure.

BATTERY

Open the battery door on the back of the device

and place the batteries according to correct

polarity. Then cover the batteries with the battery

door.

Only use 1,5V AAA Alkaline batteries or the

provided LI-ION battery (not included with Disty

40R)

If the device is not used for a longer time,

remove the batteries to avoid battery corrosion

inside the device.

MAJOR SETTINGS

TURN ON/OFF THE INSTRUMENT

Hold the Measure – ON button [2] for approx.

3 seconds to turn the device on. By starting up

the device, the laser will light up shortly. The

device is stand by for measurement.

Hold the Clear – OFF button [7] for approx.

3 seconds to turn off the device.

The device will shut down automatically after

approx. 150 seconds without any operation.

UNIT SETTINGS

Hold the Beep – Unit button [4] for approx. 3 sec-

onds to change the measurement unit. The de-

fault unit is 0.000m. There are 6 units to choose:

LENGTH AREA VOLUME

0.000 m 0.000 m20.000 m3

0.00 m 0.00 m20.00 m3

0.0 in 0.00 ft20.00 ft3

0.00 ft 0.00 ft20.00 ft3

0 1/16 in 0.00 ft20.00 ft3

0’ 00” 1/16 0.00 ft20.00 ft3

(For every change you need to release and hold

the Beep - Unit button [4] for another 3 seconds.)

CHANGING THE REFERENCE POINT

Press the Reference point – Timer button [6]

shortly to change the reference point.

There are 3 reference points which you can

choose:

Front Top of the device (with laser exit) is the

reference point

Middle The middle of the ¼” screw on the

backside is the reference point (for use

with tripod)

Back Bottom of the device is the reference

point

DELAY MEASUREMENTS

You can easily delay your measurement with

3 to 60 seconds. Hold the Reference point –

Timer button [6] for approx. 3 seconds. SEC will

be shown on the display with the number of

seconds of the delay.

To adjust the delay, press the Function – Back

button [3] and/or the Addition/Subtraction – Next

button [5] as much as needed to reach the delay

you prefer.

Press the Measure – ON button [2] to start the

countdown. The device will measure when the

countdown reaches the 0.

BACKLIGHT

The backlight will turn ON/OFF automatically.

The backlight will be on for 15 seconds while op-

erating. After 15 seconds with no operation, the

backlight will turn off automatically. It will light up

again after pressing any button.

SOUND ON/OFF

The device can produce beeping sounds. To turn

them ON of OFF, press the Beep – Unit button [4].

OPERATIONS

Below, we mention the symbol shown on the func-

tion indicator [b]. Hit the Function – Back button

[3] als much as needed until the measurement

you need is shown in the function indicator [b].

The side you need to measure will blink in the

shown symbol.

SINGLE DISTANCE MEASUREMENT

Press the Measure – ON button [2] to make a

laser beam appear and activate the measure

mode. Press the Measure – ON button [2] again

to see appear the measured length. The meas-

ured results is displayed on the major display [f].

CONTINUOUS MEASURING

Hold the Measure – ON button [2] and a con-

tinuous measuring mode will be activated. The

minimum and maximum measuring results will

be shown [d, e] and the present result will be

shown in the major display [f]. Press the Measure

– ON button [2] or on the Clear – OFF button [7]

to quit the continuous measuring mode.

AREA MEASUREMENT

Press the Function – Back button [3] once, a

square appears at the top of the screen. One of

the sides of the square/ rectangle is blinking on

the screen. Then follow the subsequent instruc-

tions to calculate the volume:

Press the Measure – ON button [2] once for the

length.

Press the Measure – ON button [2] again for the

width.

The device will show the result on the major dis-

play [f]. The current measuring result will appear

in the auxiliary display [g, h].

Press the Clear – OFF button [7] to remove and

clear the previous measurement results. Press the

same button again to exit this mode.

VOLUME MEASUREMENT

Press the Function – Back button [3] twice to

enter the volume measurement mode. A rectan-

gular shape will appear on the top of the screen.

Then follow the subsequent instructions to calcu-

late the volume:

Press the Measure – ON button [2] once for the

length.

Press the Measure – ON button [2] again for the

width.

Press the Measure – ON button [2] a third time for

the height.

The device will show the result on the major dis-

play [f]. The current measuring result will appear

in the auxiliary display [g, h, i].

Press the Clear – OFF button [7] to remove and

clear the measurement results. Press the same

button again to exit this mode.

PAINTER FUNCTION

When the device is in the surface/area function,

you can use the addition and subtraction function

to add up the different surface areas.

Press the Function – Back button [3] three times

till the Painter function symbol is visible in the

function indicator [b].

Press the Measure – ON button [2] a rst time to

measure the height of the rst wall.

Press the Measure – ON button [2] to measure

the bottom edge of the rst wall. You can see the

surface measure in the major display [f].

Press the Measure – ON button [2] to measure

the bottom edge of another wall. Afterwards you

can get the sum of these two walls.

Repeat these steps for more walls. Press the

Clear – OFF button [7] to remove and clear the

previous measurement results. This way you can

perform a new measurement.

When there is no data in the auxiliary display [g, h,

i], press the Clear – OFF button [7] to exit this mode.

BASIC PYTHAGORAS

Calculate the length of two legs by measuring

the hypotenuse and the angle.

Press 4x on the Function – Back button [3], when

the hypothenuse (a) of the triangle is blinking.

Press the Measure – ON button [2] to measure

the length of the hypothenuse (a) and to calcu-

late the angle (α) between bevel and the bottom

at the same time. The device will calculate the

horizontal distance (b) and the vertical height (h).

LENGTH OF HYPOTHENUSE

Calculate the hypotenuse by measuring the

length of two legs.

Calculate the hypothenuse by measuring the

length of two legs. Press the Function – Back

button [3] 5x till one leg of the triangle is blinking

on the screen.

Press the Measure – ON button [2] to measure

the length of one leg (a).

Press the Measure – ON button [2] again to meas-

ure the length of the other leg (b).

The device will calculate the length of hypoth-

enuse (x).

DOUBLE PYTHAGORAS

VIA SUBTRACTION

Press the Function – Back button [3] 6x till one

side of the triangle is blinking on the screen.

Press the Measure – ON button [2] to measure

the length of one side (rst hypothenuse - a).

Press the Measure – ON button [2] again to

measure the length of the median line (second

hypothenuse - b).

Press the Measure – ON button [2] a third time to

measure the length of another, horizontal side (c).

The device will calculate the length of the length

of the leg (x).

DOUBLE PYTHAGORAS VIA SUM

Press the Function – Back button [3] 7x till the hy-

potenuse of the triangle is blinking on the screen.

Press the Measure – ON button [2] to measure

the length of rst hypothenuse (a).

Press the Measure – ON button [2] to measure

the length of the horizontal hypothenuse (b).

Press the Measure – ON button [2] to measure

the length of third hypothenuse (c).

The device will calculate the length of the leg (x).

The legs must be shorter than the hypothenuse

otherwise an “err” will be shown on the screen.

In order to guarantee the accuracy, please make

sure that all measurements are performed from

the same starting point.

We recommend using a tripod with tilting head.

HANDLING MEASURED DATA

ADDITION/ SUBTRACTION

The device can be used for length addition and

subtraction.

Press the Addition/ Subtraction – Next button [5]

to select the function once you have the length

measuring result. Press the Addition/ Subtrac-

tion – Next button [5] and a “+” will be shown in

the major display. The + shows that the addition

mode is activated. The value of the last meas-

urement and the result of the cumulation will be

showed on the screen.

Press the Addition/ Subtraction – Next button [5]

again and a “-“ shows in the major display. The –

shows that the regressive mode is activated. The

value of the last measurement and the result of

the cumulation will be showed on the screen.

By pressing the Addition/ Subtraction – Next

button [5], you can switch between the addition

and subtraction mode.

Not only lengths can be added of substracted,

but it can also calculate sum or substraction of

the areas and volumes.

An example with summing two areas:

PIC1 PIC2 PIC3

Area cumulative function:

Measure the rst area as showing in PIC1.

Then press the Addition/ Subtraction – Next but-

ton [5] and measure the second area as showing

in PIC2. A + is showing in the left bottom of the

screen.

At last, press the Measure – ON button [2] to get

the summation result of the two areas. This result

is showed in PIC3.

MEMORY FUNCTION

STORE MEASUREMENTS

Hold the Memory- Save button [8] for 3 seconds

to record your measuring result. You can record

the result of all the operation modes. Calcula-

tions can be saved too.

READ AND DELETE RECORDS

Press the Memory- Save button [8], then you can

read the records by pressing the Function – Back

button [3] and the Addition/ Subtraction – Next

button [5]. Press the Clear – OFF button [7] to

delete the displayed record. Hold this button

to clear all the records. Press the Memory- Save

button [8] or the Measure – ON button [2] to exit

the record mode.

When the storage is full, the screen will show a

“FUL” mark.

ANGLE MEASUREMENT

The angle information is displayed at the top

of the screen. The angle measurement range is

-90.0° to 90.0°.

SELF-CALIBRATION

This function ensures that the precision of the

device is maintained.

Power off and press the Clear – OFF button

[7] and the Measure – ON button [2] till “ CAL”

appears. The user can adjust the gure, that

appeared on the screen, with the Function – Back

button [3] or the Addition/ Subtraction – Next

button [5], according to the accuracy of the

meter.

Adjusting range: -9 to 9mm, then press the Meas-

ure – ON button [2] to save the calibration result.

INSTRUMENT MAINTENANCE

The meter should not be stored in high temper-

atures and strong humidity environments for

too long. If it is not used often, please take out

the battery and place the meter in the allocated

pouch. Store the pouch in a cool and dry place.

Please keep the device surface clean. Use a wet

soft cloth to clean dust. Never use erosion liquid

for the meter maintenance. Laser output window

and its focus lens can be maintained according

to maintenance procedures for optical device.

TIPS

You may get some warning information as below:

INFO

MESSAGE CAUSE SOLUTION

Err Out of distance

measurement range

Use the device within the

range.

Err1 Signal is

too weak

Chose the surface with

stronger reectance.

Use the reecting plate.

Err2 Signal is

too strong

Chose the surface with

weaker reectance.

Use the reecting plate.

Err3 Low battery voltage Change the power supply

Err4 The working

temperature is out of

working range

Use the device in

the specied

temperature

Err5 Pythagoras

measuring error

Re-measure and ensure that

Hypotenuse is

bigger than Cathetus.

Err6 Angle sensor error Depot repair

NOTE

Use a target plate to increase the measurement

range during daylight or if the target has poor

reection properties.

Altri manuali per DISTY 40R

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Futech Strumento di misura

Futech

Futech MULTICROSS 4D ELECTRONIC Manuale utente

Futech

Futech MULTICROSS 3 Manuale utente

Futech

Futech MULTICROSS 5 SUPER Vision Manuale utente

Futech

Futech DM3540 Manuale utente

Futech

Futech EAGLE 24 Manuale utente

Futech

Futech DISTY 120RC Manuale utente

Futech

Futech MEGACROSS Manuale utente

Futech

Futech MULTICROSS 3 Super Vision Manuale utente

Futech

Futech MULTICROSS 5 SUPER Vision Manuale utente

Futech

Futech MULTICROSS 3D COMPACT Manuale utente

Futech

Futech PARA DS Manuale utente

Futech

Futech DISTY 120RC Manuale utente

Futech

Futech DISTY40 Manuale utente

Futech

Futech PLUTO 1.2 Manuale utente

Futech

Futech Gyro GS Manuale utente

Futech

Futech AMPCLAMP 1000 Manuale utente

Futech

Futech DISTY 40R Manuale utente

Futech

Futech PROCROSS 8.0 DS Guida all'installazione

Futech

Futech MULTICROSS 8 HIGH PRECISION SUPER BRIGHT... Manuale utente

Futech

Futech MULTIPOWER 3.6 COMPACT Manuale utente

Futech

Futech DECACROSS Manuale utente

Futech

Futech T-BEVEL-30 Manuale utente

Futech

Futech PROCROSS 8.0 DS Manuale utente

Futech

Futech MULTICROSS 3 Super Vision Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente