GBC AutoUltima Pro Manuale utente
AutoUltima Pro
Laminator
G
Instruction Manual
F
Manuel d’utilisation
D
Bedienungsanleitung
I
Manuale d’istruzioni
O
Gebruiksaanwijzing
E
Manual de instrucciones
P
Manual de Instruções
S
Bruksanvisning
Q
Instrukcja obsługi
o
Návod k obsluze
H
Használati útmutató
o
Руководствo по
зкcплyатации
CZ
RUS
English 4
Français 16
Deutsch 28
Italiano 40
Nederlands 52
Español 64
Português 76
Svenska 88
Polski 100
Česky 112
Magyar 124
Pyccкий 136
4
Start Stop
Enter
17
8
9
J
K
L
2
3
4
4
M
N O
5
6
4
General safeguards
• Use this laminator only for its intended purposes as according to the
specifications outlined in the operating instructions.
• Keep hands, long hair, loose clothing and articles such as necklaces
or ties away from the front of the pull rollers to avoid entanglement
and entrapment
• Avoid contact with the heat shoes during operation or shortly after the
laminator has been turned off, The heat shoes can reach temperatures
in excess of 30O"F.
• Keep hands and fingers away from the path of the sharp film cutter
blade located at the film exit.
• Place the laminator on a stable cart, stand or table capable of
supporting at least 50kg. An unstable surface may cause the laminator
to fall resulting in serious bodily injury, Avoid quick stops. excessive
force and uneven floor surfaces when moving the laminator on a cart
or stand.
• Do not defect or remove electrical and mechanical safety equipment
such as interlocks, shields and guards.
• Do not insert objects unsuitable for lamination.
• Do not expose laminator to liquids.
THE FOLLOWING WARNINGS ARE FOUND ON THIS PRODUCT.
Electrical shock hazard.
Do not open. No user
serviceable parts inside.
Refer servicing to qualified
service personnel.
WARNING
m
c
This safety message means that you could be seriously hurt or killed if
you open the product and expose yourself to hazardous voltage.
THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY
MESSAGE IN THIS INSTRUCTION MANUAL.
ON THE PRODUCT YOU WILLFIND IMPORTANT SAFETY
MESSAGES. READ THESE MESSAGES AND INSTRUCTIONS
CAREFULLY SAVE THESE INSTRUCTIONS FOR LATER USE.
m
Important safety instructions
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS IMPORTANT
TO ACCO BRANDS EUROPE. IN THIS INSTRUCTION MANUAL AND ON
THE PRODUCT ARE IMPORTANT SAFELY MESSAGES. READ THESE
MESSAGES CAREFULLY.
m
Do not touch heat shoes until they have cooled.
Hot
surface.
CAUTION
m
This safety message means that you could cut yourself if you are not
careful.
SHARP BLADE.
Keep hand and
fingers away.
CAUTION
m
WARNING: THE SAFETY ALERT SYMBOL PRECEDES
EACH SAFETY MESSAGE IN THIS INSTRUCTION
MANUAL. THIS SYMBOL INDICATES A POTENTIAL
PERSONAL SAFETY HAZARD THAT COULD HURT YOU
OR OTHERS, AS WELL AS CAUSE PRODUCT DAMAGE OR
PROPERTY DAMAGE.
m
WARNING: DO NOT ATTEMPT TO SERVICE OR REPAIR
THE LAMINATOR.
m
WARNING: DO NOT CONNECT THE LAMINATOR TO AN
ELECTRICAL SUPPLY OR ATTEMPT TO OPERATE THE
LAMINATOR UNTIL YOU HAVE COMPLETELY READ THESE
INSTRUCTIONS. MAINTAIN THESE INSTRUCTIONS IN A
CONVENIENT LOCATION FOR FUTURE REFERENCE.
m
WARNING: FOR YOUR PROTECTION, DO NOT CONNECT
THE LAMINATOR TO ELECTRICAL POWER OR ATTEMPT
TO OPERATE UNTIL YOU READ THESE INSTRUCTIONS
COMPLETELY. KEEP OPERATING INSTRUCTIONS IN
A CONVENIENT LOCATION FOR FUTURE REFERENCE.
TO GUARD AGAINST INJURY, THE FOLLOWING BASIC
SAFETY PRECAUTIONS MUST BE OBSERVED IN THE
SET·UP AND USE OF THE LAMINATOR.
m
Important safeguards m
Electrical safeguards
• This laminator must be connected to a supply voltage corresponding
to the electrical rating as indicated on the serial plate located on the
rear of the machine.
• Unplug the laminator before moving it, or when it is not in use for an
extended period of time.
• Do not operate the laminator with a damaged power supply cord or
plug.
• Do not overload electrical outlets as this can result in fire or shock.
• Do not alter the attachment plug, This plug is configured for the
appropriate electrical supply.
• The unit is intended for indoor use only.
CAUTION: The power source must be located near the
equipment and easily accessible. Do not use an extension cord.
• Disconnect the attachment plug from the power source to which it is
connected and keep the power supply cord in your possession while
moving the laminator.
• Do not operate the laminator with a damaged power supply cord or
attachment plug, upon occurrence of a malfunction, or after laminator
has been damaged. Contact an authorized GBC service representative
for assistance.
m
m
5
G
Location of controls
1 Feed Tray
2 Paper Side Guide
3 Top Cover
4 Control Panel
5 Exit Tray
6 Power Button
7 4 EZ Load Levers
8 Heat Button
9 Feed Switch
J Idler Bar Assembly
K Heat Shoe
L Film Roll
M Power LED (Red)
N Ready LED (Green)
O Scroll Button
Perform only the routine maintenance procedures referred to in these
instructions.
Do not attempt to service or repair the laminator.
Unplug the unit and contact an authorised GBC service representative if
one or more of the following has occurred:
• The power supply cord or attachment plug is damaged.
• Liquid has been spilled into the laminator.
• The laminator is malfunctioning after being mishandled.
• The laminator does not operate as described in these instructions.
m
Service
WARNING: THIS IS NOT A TOY - DO NOT ALLOW
CHILDREN TO OPERATE THIS LAMINATOR!
m
Installation
• Shipping damage should be brought to the immediate attention of the
delivering carrier.
• Place the laminator on a stable flat surface capable of supporting
50kg. The surface should be at least 76cm high to assure comfortable
positioning during operation. All four rubber feet should be on the
supporting surface.
• Connect power cord to an appropriate power source. Avoid connecting
other equipment to the same branch circuit to which the laminator is
connected as this may cause nuisance tripping of the circuit breaker
or blown fuses.
• The laminator should be positioned to allow exiting film to drop freely
to the floor. Accumulation of laminate as it exits the laminator may
cause film to wrap around the rollers causing a jammed condition.
• Avoid placing laminator near sources of heat or cold. Avoid locating the
laminator in the direct path of forced, heated or cooled air.
Caring for the AutoUltima Pro Laminator
The only maintenance required by the operator is to periodically dean
the heal shoes. This should only be done when changing film rolls,
please see page 7 steps 1, 2, &3. The following procedure will help keep
the heal shoes free of adhesive that has been deposited along the edge
of the laminating film.
CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED
WHILE THE LAMINATOR IS HOT. USE EXTREME CAUTION.
WARNING: Do not apply cleaning fluids or solvents to
the rollers.
WARNING: Do not attempt to laminate adhesives
marked 'flammable'.
1 Preheat the laminator using the heat button.
2 Clean the top and bottom heat shoes with a soft cloth.
3 Follow the procedure on page 7, steps 4, 5, 6 & 7.
NOTE: Do not use metal scouring pads to clean the heat shoes!
WARNING: Do not laminate glitter and/or metallic items. Damage to
the rollers may result.
m
m
m
6
AutoUltima Pro - Setup
Laminator comes pre-Ioaded with 75mic film, Approximately 90 metres.
1 In back of machine turn on power.
Power light LED front control panel
lights up.
4 Insert and secure feed tray into
position.
Enter
2 First time only, scroll up or down
to select language setting, then
press "Enter". To reset language,
hold down both scroll buttons for
5 seconds, select language then
press enter.
3 Open tray for normal operation. For
longer paper or banners close tray.
Tra y
5 Adjust "Paper Side Guides" to fit
document(s).
Side
Guides
AutoUltima Pro - Setup
Laminator comes pre-Ioaded with 75mic film, Approximately 90 metres.
3 Laminated document(s) will stack
in Exit Tray. Lamination will stop
when job is complete.
1 Adjust paper side guides and place
document(s) in feed tray.
Side
Guides
Start Stop
Enter
2 Press start and lamination will
begin after warm up.
Screen
Start Stop
Enter
4 LCD screen will display number of
documents being laminated.
Screen
7
G
AutoUltima Pro – Load Film
IF POSSIBLE, ALWAYS LOAD FILM BEFORE RUNNING COMPLETELY OUT.
1 Cut laminating film as indicated. If
film is not present see next page.
5 Insert and lock Idler Bar Assembly,
then close 4 EZ Load levers.
2 Open all 4 "EZ" Load levers and
remove film.
4 Insert new film, overlap film on
Heat Shoe.
Note: Match colours of film core
ends to EZ Load Levers.
3 Remove Idler Bar Assembly, then
press "Heat" button.
Heat
Button
6 Press feed switch (forward) and
hold until wrinkle-free lamination.
Close top.
7 Scroll up or down to select film
thickness. Press "Enter" to
confirm. Press "Start" to resume
lamination. To reset film thickness,
hold enter button for 5 seconds,
select film thickness then press
"Enter".
Screen
8
AutoUltima Pro – Load Film
USE INSTRUCTIONS BELOW TO LOAD NEW FILM IF COMPLETELY EMPTY.
1 First, complete steps 2, 3 and 4
from "Load Film" page 7. Close 4
EZ levers.
2 Press "Feed" switch (forward)
and insert "Feed Card" as shown.
Insert card with slight force
through film rollers.
3 Insert Idler Bar Assembly. Continue
pressing feed switch and wait for
clear, wrinkle-free lamination.
4 Close top cover, scroll up or down
to select film thickness. Press
"Enter" to confirm. Press "Start" to
resume lamination.
Screen
AutoUltima Pro – Status Message
Laminator comes pre-Ioaded with 75mic film, Approximately 90 metres.
Standby Screen.
Counting screen,
showing pages
laminated so far.
Load document(s) to
be laminated.
Job complete screen.
Total pages laminated.
Machine is in heat
mode. Machine is
warming to operating
temperature.
9
G
AutoUltima Pro – Alert Messages
Do not attempt to take machine apart - No User Servicable Parts.
TOP COVER ALERT
Top cover is open. Close it and resume
lamination.
FRONT DRAWER ALERT
Close front drawer and resume
lamination.
LOW FILM ALERT
Open top cover and load new film rolls.
Refer to "Load Film", pg. 7 and 8.
IDLER BAR ASSEMBLY ALERT
Insert and lock the Idler Bar assembly.
Close top cover and resume
lamination.
(Alert Message)
(Alert Message)
(Alert Message)
(Alert Message)
10
AutoUltima Pro – Error Messages
Do not attempt to take machine apart - No User Serviceable Parts.
FEED JAM ERROR
Remove document(s) and any debris
from feed tray, Fan documents and
adjust size guides, Press "Start" to
resume.
(Jam Message)
Jam Location
JAM ERROR
A) Open covers
B) Locate film Jam
C) Press Heat button
Use Feed switch (forward/reverse) to
clear jam, It may be necessary to cut
and remove film, (Take care not to
damage rollers when cutting film), If
cutting is required, use Feed switch
(forward I reverse) to re-feed film
through machine.
(Jam Message)
(Jam Message)
Jam Location
Jam Location
Jam
Jam
Indice
Lingue:
Altri manuali GBC Plastificatrice
GBC
GBC Discovery 50 Manuale utente
GBC
GBC HEATSEAL H220 Manuale utente
GBC
GBC 4500 Manuale utente
GBC
GBC 40 Manuale utente
GBC
GBC Fusion 5000L Manuale di istruzioni
GBC
GBC Inspire Plus A4 Manuale utente
GBC
GBC HeatSeal H535 Turbo Manuale utente
GBC
GBC HeatSeal Sprint H950 Manuale utente
GBC
GBC Inspire Manuale utente
GBC
GBC HeatSeal H65 Manuale utente
GBC
GBC HeatSeal H520 Manuale utente
GBC
GBC Fusion 5000L A3 Manuale utente
GBC
GBC 4120 Manuale utente
GBC
GBC HeatSeal H212 Manuale utente
GBC
GBC DocuSeal 40P Manuale utente
GBC
GBC H320 Manuale utente
GBC
GBC Ultima 65 Manuale utente
GBC
GBC Spire III 44T Manuale utente
GBC
GBC 13 PRO Manuale utente
GBC
GBC Falcon 60+ (-1) Manuale utente
