Gira 0388 00 Manuale utente

Blind controller insert DC 24 V

Order-No. : 0388 00

Operating instructions

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Failure to observe the instructions may cause damage to the device and result in fire and

other hazards.

To supply the insert and to control the extension inputs it is necessary to use a power

supply unit that provides DC 24 V SELV. This ensures reliable isolation between the

primary and secondary sides.

Risk of injury. Use the device only for controlling Venetian blind and roller shutter

motors or awnings. Do not use it to switch other loads.

Use only Venetian blind drives with mechanical or electronic limit switches. Check the

limit switches for correct adjustment. Observe the specifications of the motor

manufacturers. Device can be damaged.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

Figure 1

(1) 24 V insert

(2) Frame

(3) Shutter cover

(4) Terminals

(5) Space for sensor terminal block

3 Function

Intended use

- Control of electrically-driven Venetian blinds, shutters and awnings that are operated with

DC 24 V SELV

- Operation with suitable shutter cover

- Installation in appliance box to DIN 49073

1/8

32545312 17.05.2011

Blind controller insert DC 24 V

10499098 I00

Blind control system

Product characteristics

- Integration into groups or master control via extension units with additional 24 V inserts

- Operation as a main device or extension unit

- Supports sensor functions of the cover

- Several motors can be connected in parallel

- The direction of rotation of the shutter motor is determined by switching the polarity of the

motor outputs "pole-changing principle" (Figure 2)

Figure 2: Control of the shutter motor

(6) Relay contacts for moving up

(7) Relay contacts for moving down

4 Operation

Moving the blind/shutter

o Press top or bottom of cover for longer than one second.

The Venetian blind moves in the desired direction to the end position or stops when the

button is pressed again.

Adjusting the slats

o Press top or bottom of cover for shorter than one second.

The slat position changes in the desired direction for as long as the button is pressed.

Moving the blind/shutter via a mechanical extension

o Press the button for moving up or down until the blind/shutter has reached the desired

position.

5 Information for electrically skilled persons

5.1 Fitting and electrical connection

Connecting and mounting the insert

Operate the insert only with a DC 24 V SELV power supply unit.

32545312 10499098 I00 17.05.2011 2/8

Blind control system

Blind controller insert DC 24 V

Figure 3: Connection diagram for insert

o Connect the shutter motor and power supply unit (8) to the insert (1) according to the

connection diagram (Figure 3).

o For a shutter cover with sensor evaluation, install the sensor cable in accordance with

(Figure 8) or (Figure 9) (Installing the sensor cable).

o If necessary connect extension (Figure 4).

o Install insert in appliance box, terminals must be at the bottom.

o Attach the frame and the cover.

o Check function. If the blind/shutter moves in the wrong direction, exchange the

connections.

Connecting an extension

DANGER!

Danger of electrical shock when 230 V is connected to the extension inputs!

Electrical shocks can be fatal.

Do not connect the extension inputs with 230 V extensions or other 230 V

components.

The extension inputs "1" and "2" may only be connected to DC 24 V SELV.

32545312 10499098 I00 17.05.2011 3/8

Blind control system

Blind controller insert DC 24 V

Figure 4: Connection assignment of extension inputs for the corresponding directions of motion

The direction of rotation of the shutter motor is determined by the polarity of the two extension

inputs. Connection illustration (Figure 4) shows the direction of motion of the blind/shutter for

the depicted connection assignments.

Figure 5: Insert with an additional 24 V insert as an extension

32545312 10499098 I00 17.05.2011 4/8

Blind control system

Blind controller insert DC 24 V

Figure 6: Connection diagram for insert with mechanical extension

The insert can only be operated with a mechanical extension if the insert and the extension are

supplied by the same power supply unit. The insert and extension then have the same "-"

potential, and it is sufficient to connect the "+" potential via the extension.

If the extension is supplied via another power supply unit, an additional 24 V insert (10) must be

used that connects both extension inputs.

Figure 7: Connection diagram for two inserts supplied via two power supply units

o Connect extension according to connection diagram (Figure 5), (Figure 6) or (Figure 7).

Installing the sensor cable

for covers with sensor evaluation

i The sensor cable carries safety extra-low voltage (SELV). Observe fitting instructions

according to VDE 0100.

The sensor cable can be installed in three different ways. In-wall routing (Figure 8), surface-

mounted routing (Figure 9), and with appropriate covers plugging the sensor cable into the

cover (Figure 11).

32545312 10499098 I00 17.05.2011 5/8

Blind control system

Blind controller insert DC 24 V

i The sensor cable must not be too long, because otherwise interference from other loads

and cables may occur. This may result in malfunctions. Therefore use only shielded cables,

and connect the shielding to earth. The total length must not exceed 20 m; avoid proximity

to other electrical facilities.

Routing the sensor cable in-wall

Figure 8: In-wall routing of the sensor cable

i For in-wall routing of the sensor cable, use only shielded cables. Recommendation: J-Y

(ST)Y 2x2x0.6 mm.

o Insert the cable through the hole (11) in the insert and route it through the cable duct (12)

to the terminal block (13) (Figure 8).

i The terminal block is included with the covers with sensor evaluation.

o Connect the cable (see "Connecting sensors to terminal block")

Routing the sensor cable with surface-mounting

Figure 9: Surface-mounted routing of the sensor cable

o For surface-mounted routing of the indoor sensor (15), cut off the plug.

32545312 10499098 I00 17.05.2011 6/8

Blind control system

Blind controller insert DC 24 V

o Route the sensor cable behind the supporting plate (14) and through the cable duct to the

connecting terminal (13) (Figure 9).

o Connect the cable (see "Connecting sensors to terminal block")

Connecting sensors to terminal block

Figure 10: Connection to the terminal block

o Connect sensors as shown in connection illustration (Figure 10). The sensor cables are

identified as follows:

For the sensors, the "earth" is identified.

For the adapter and the extension cable, the "sun" is identified. The "earth" is the middle

cable.

i Interchanging the connections will result in malfunctions.

i If the sun and glass break sensor are used at the same time, an adapter must be used.

The adapter is connected to a cover with sensor evaluation or to the insert via the

3-pole terminal block. The adapter has two sockets for connecting the sensor plug.

Plugging the sensor cable into the cover

Figure 11: Sun sensor on the cover

32545312 10499098 I00 17.05.2011 7/8

Blind control system

Blind controller insert DC 24 V

It is only possible to connect the sun sensor to the cover if a corresponding socket is present.

This is not the case for all covers with sensor evaluation.

o Insert plug (17) into the socket of the insert (16) (Figure 11).

6 Appendix

6.1 Technical data

Rated voltage DC 24 V (incl. ripple)

Power loss approx. 2,4 W

Standby power approx. 0,7 W

Switching current max. 3 A

Contact type µ contact, 2 change-over relays

Length of the sensor cable max. 20 m

Connection

Single stranded max. 2.5 mm²

6.2 Warranty

The warranty is provided in accordance with statutory requirements via the specialist trade.

Please submit or send faulty devices postage paid together with an error description to your

responsible salesperson (specialist trade/installation company/electrical specialist trade). They

will forward the devices to the Gira Service Center.

Gira

Giersiepen GmbH & Co. KG

Elektro-Installations-

Systeme

Industriegebiet Mermbach

Dahlienstraße

42477 Radevormwald

Postfach 12 20

42461 Radevormwald

Deutschland

Tel +49(0)21 95 - 602-0

Fax +49(0)21 95 - 602-399

www.gira.de

[email protected]

32545312 10499098 I00 17.05.2011 8/8

Blind control system

Blind controller insert DC 24 V

Indice

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente