Gira One 5065 00 Manuale utente
Dimming actuator 1-gang 200 W with binary input, 3-gang
Table of Contents
1 Safety instructions.............................................................................................................3
2 Device components...........................................................................................................4
3 Function ............................................................................................................................5
4 Information for electrically skilled persons ........................................................................7
4.1 Mounting and electrical connection........................................................................ 7
4.2 Commissioning ...................................................................................................... 9
5 Technical data.................................................................................................................10
6 Troubleshooting ..............................................................................................................12
7 Accessories.....................................................................................................................14
8 Parameter list ..................................................................................................................15
9 Warranty..........................................................................................................................19
2 / 19
82404412 02.12.2022
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual
fully.
Danger of electric shock. Device is not suitable for disconnection from supply voltage
because mains potential even is applied on the load when the output is switched off.
Always disconnect before carrying out work on the device or load. To do so, switch
off all associated circuit breakers.
Danger of electric shock. Make sure during the installation that there is always suffi-
cient insulation between the mains voltage and the bus. A minimum distance of at
least 4 mm must be maintained between bus conductors and mains voltage cores.
Danger of electric shock on the installation. Do not connect any external voltage to
the inputs. The device might be damaged, and the SELV potential on the bus line will
no longer be available.
Fire hazard. For operation with inductive transformers, each transformer must be
fused on the primary side in accordance with the manufacturer's instructions. Only
safety transformers according to EN 61558-2-6 may be used.
Risk of destruction of the dimmer and load if the set operating mode and load type do
not match. Set the correct dimming principle before connecting or exchanging the
load.
This manual is an integral part of the product, and must remain with the end cus-
tomer.
3 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
2 Device components
Image1: Device components
(1) Programming LED
(2) Programming button
(3) Control cable (bus connection and extension inputs)
(4) Load connection (dimming output)
Image2: Connection assignment of control cable (example)
red (RD) KNX / One +
black (BK) KNX / One -
green (GN) Input 1 (push-button, switch, contact, condensation/leakage sensor)
yellow (YE) Input 2 (push-button, switch, contact, condensation/leakage sensor)
white (WH) Input 3 (push-button, switch, contact, condensation/leakage sensor,
NTC temperature sensor)
brown (BN) COM inputs 1...3
4 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
3 Function
System information
This device is a product for the Gira One Smart Home system. The Gira One system
is commissioned easily and in a time-saving manner using the Gira Project Assistant.
The Gira One Smart Home system enables the control and automation of lighting,
heating and shading, as well as connection to various third-party systems and much
more. It can be operated via Gira One switches, by app from home or securely from a
remote location. Electrically skilled persons can maintain the Gira One project re-
motely free of charge.
Data transmission between the Gira One devices is encrypted. This provides protec-
tion against third-party access and manipulation.
Commissioning is carried out with the free Gira Project Assistant (GPA), version 5 or
higher. Free function and security updates are also transferred to the Gira One
devices with the GPA.
The Gira One system is based on the globally proven KNX smart home standard.
Intended use
– Operation in Gira One system
– Switching and dimming of lighting
– Reading in switching states of installation switches or push-buttons and other
potential-free contacts at inputs 1...3
– Signal evaluation of condensation and leakage sensors at inputs 1...3 (see ac-
cessory).
– Acquisition of temperature values via NTC temperature sensor at input 3 (see
accessories)
– Mounting in appliance box with dimensions according to DIN 49073
Product characteristics
– Output can be operated via the Gira One system or extension inputs
– Three extension inputs for connecting potential-free contacts or dew/leakage
sensors. NTC temperature sensor can be connected to input 3.
– Supply via the bus, no additional supply voltage necessary
– Actuator for switching and dimming of incandescent lamps, HV halogen lamps,
dimmable HV LED lamps, dimmable compact fluorescent lamps, dimmable in-
ductive transformers with LV halogen or LV LED lamps, dimmable electronic
transformers with LV halogen or LV LED lamps.
– Automatic or manual selection of the dimming principle suitable for the load.
– Protected against no-load, short-circuit and overheating.
– Power extension by means of power packs.
5 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
– Programming and commissioning with the Gira Project Assistant (GPA), ver-
sion 5 or higher.
– Updating via the Gira Project Assistant (GPA).
– Encrypted data transmission between the Gira One devices.
Dimming operation characteristics
– Minimum and maximum brightness can be set.
– Switching on to last brightness value or to permanently set switch-on bright-
ness.
– Setting of a switch-on or switch-off delay.
– Staircase function for which a pre-warning time and a pre-warning brightness
can optionally be set.
Flickering of the connected lamps due to undershoot of the specified minimum
load or through centralised pulses from the power stations. This does not rep-
resent any defect in the device.
Extension input characteristics
– Single or dual-area operation can be configured for rockers.
– Connection of rockers that are configured with the function for switching, dim-
ming, shading and ventilation, scene recall, staircase (motion detector), floor
call, garage door and door opener.
– Connection of motion and presence detectors with potential-free relay outputs.
– Convenient group control of switching, dimming, shading and ventilation loads.
– Switching contact evaluation of wind, frost, brightness or rain sensors with po-
tential-free relay outputs possible in order to protect shading and ventilation
loads against environmental influences.
– Window contact polling and visualisation in the Smart Home app: An open
window leads to the frost protection heating mode after a configured time has
elapsed.
– Door contact polling and visualisation in the Smart Home app: An open door
leads to the Venetian blind or shutters being raised and locked.
– Polling of a switch-over between heating/cooling at a heat pump in order to be
able to forward the current operating mode (heating or cooling) to a heating
controller.
– Switching contact indicator for displaying a contact state in the Smart Home
app.
– Configurable switching inputs that can be parameterised independently.
– Acquisition and calibration of temperature values via remote sensors (see ac-
cessories) at input 3.
6 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
4 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
4.1 Mounting and electrical connection
DANGER!
When connecting the bus/extensions and mains voltage wires in a shared appliance
box, the bus line may come into contact with the mains voltage.
This endangers the safety of the entire installation. People at remote devices may
also receive an electric shock.
Do not place bus/extensions and mains voltage terminals in a shared connection
compartment. Use an appliance box with a fixed partition wall or separate appliance
boxes.
Connecting and fitting the device
– Enter or scan the device certificate and add it to the project. A high resolution
camera should be used to scan the QR code.
– The device certificate should be removed from the device during mounting.
– Document all passwords and keep them safe.
Mounting in suitable appliance box (recommendation: electronic device box with par-
tition). Observe cable routing and spacing (see figure 3)!
7 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
Image3: Mounting example in electronic appliance box with partition wall, series
push-button and NTC temperature sensor
(5) Appliance box
(6) Partition
(7) potential-free contacts (e.g. series push-button)
(8) NTC temperature sensor (optional)
Image4: Cable spacing
Minimum spacing between the mains voltage and bus/extension wires: 4 mm
(see figure 4)
Image5: Connection of load
8 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
Observe ambient temperature. Ensure adequate cooling.
￭ Connect bus line, observing the correct polarity.
￭ Connect load as shown in the connection example (see figure 5).
￭ If required, connect potential-free contacts or condensation/leakage sensors to
inputs 1...3, or NTC temperature sensors to input 3 (see figure 2).
￭ Install the device in the appliance box.
The COM reference potential must not be connected together with COM con-
nections of other devices!
4.2 Commissioning
Commissioning the device
Delivery state: The output is set to the universal dimming principle with automatic re-
cognition of the load type. Operation of the output is possible via input 1 (ON/
Brighter) and input 2 (OFF/Darker). Input 3 has no function.
Function of Inputs in the as-delivered state
Input Push-button (NO con-
tact)
Function
1 Press briefly (< 0.4 s) Switch on
1 Press for a long time (>
0.4 s)
Increase brightness
2 Press briefly (< 0.4 s) Switch off
2 Press for a long time (>
0.4 s)
Reduce brightness
3 --- ---
The device is commissioned with the Gira Project Assistant (GPA) version 5 or
higher.
Safe-state mode
The safe-state mode stops the execution of the program.
Only the system software of the device is still functional. Diagnosis functions and pro-
gramming of the device are possible.
Activating safe-state mode
￭ Switch off the bus voltage or disconnect the device from the bus.
￭ Wait about 10 s.
￭ Press and hold down the programming button.
￭ Switch on the bus voltage or connect the bus again at the device. Release the
programming button only after the programming LED starts flashing slowly.
The safe-state mode is activated.
9 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
Deactivating safe-state mode
￭ Switch off the bus voltage (wait approx. 10 s) or carry out programming.
Master reset
The master reset restores the basic device settings (firmware remains in place). The
device must then be recommissioned with the GPA.
Performing a master reset
Precondition: The safe-state mode is activated.
￭ Press and hold down the programming button for > 5 s.
The programming LED flashes quickly.
The device performs a master reset, restarts and is ready for operation again
after approx. 5 s.
5 Technical data
Rated voltage DC 21 ... 32 V SELV
Current consumption 5 ... 18 mA
Connection mode Device connection terminal on control
cable
Output
Rated voltage AC 230 V ~
Mains frequency 50 / 60 Hz
Power loss max. 1.5 W
Standby power approx. 0.2 W
Connection mode Screw terminals
Connected loads see tables: (see figure 6) and (see figure 7)
Load types
UNI universal (with automatic calibration procedure)
LJconv. transformer (inductive / leading edge phase control)
|LED (leading edge phase control)
dželectr. transformer (capacitive / trailing edge phase control)
{LED (trailing edge phase control)
10 / 19
82404412 02.12.2022
Dimming actuator 1-gang 200 W with binary input, 3-gang
Indice
Altri manuali Gira Controllori
Gira
Gira 1039 00 Manuale utente
Gira
Gira 2100 Series Manuale utente
Gira
Gira KNX 1039 00 Manuale utente
Gira
Gira Powernet Single Switching Actuator Manuale utente
Gira
Gira System 3000 Manuale utente
Gira
Gira KNX 5061 00 Manuale utente
Gira
Gira KNX 213900 Manuale utente
Gira
Gira 0309 00 Manuale utente
Gira
Gira G1 Manuale utente
Gira
Gira 0570 00 Manuale utente
Gira
Gira System 3000 Manuale utente
Gira
Gira 0566 Series Manuale utente
Gira
Gira One 5061 00 Manuale utente
Gira
Gira 2114 00 Manuale utente
Gira
Gira Powernet Switchactuator 2fold Manuale utente
Gira
Gira One 5023 00 Manuale utente
Gira
Gira One 5062 00 Manuale utente
Gira
Gira 1288 Series Manuale utente
Gira
Gira 5431 00 Manuale utente
Gira
Gira 1289 00 Manuale utente
