Hamilton Beach UltraSteam Manuale utente

UltraSteam™Iron

840068700

Iron Safety ...................................... 2

Know Your Iron .............................. 3

Before First Use ............................ 4

Using Your Iron................................ 4

Features .......................................... 6

Storing Your Iron ............................ 8

Troubleshooting ............................ 10

Customer Service ........................ 11

In USA: 1-800-851-8900

In Canada: 1-800-267-2826

Consumer Safety Information

This appliance is equipped with a polarized plug. This type of plug has one blade wider

than the other. The plug will fit into an electrical outlet only one way. This is a safety feature

intended to help reduce the risk of electrical shock. If you are unable to insert the plug into the

outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified electrician

to replace the obsolete outlet. Do not attempt to defeat the safety purpose of the polarized

plug by modifying the plug in any way.

IMPORTANT SAFEGUARDS

SAVE THESE INSTRUCTIONS!

Iron Safety

When using your flat iron, basic safety precautions should always be followed, including

the following:

READ ALL INSTRUCTIONS BEFORE USING

1. Use iron only for its intended use.

2. To protect against risk of electric shock, do not immerse the iron in water or other liquids.

3. The iron should always be turned to OFF ( 0) before plugging or unplugging from outlet.

Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.

4. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away.

Loop cord loosely around iron when storing.

5. Always disconnect iron from electrical outlet when filling with water or emptying and

when not in use.

6. Do not operate iron with a damaged cord or if the iron has been dropped or damaged.

To avoid the risk of electric shock, do not disassemble the iron. Call our toll-free

customer service number for information on examination and repair. Incorrect

reassembly can cause a risk of electric shock when the iron is used.

7. Close supervision is necessary for any appliance being used by or near children. Do not

leave iron unattended while connected or on an ironing board.

8. Burns can occur from touching hot metal parts, hot water, or steam. Use caution when

you turn a steam iron upside down – there may be hot water in the reservoir.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high wattage appliance on the

same circuit.

2. If an extension cord is absolutely necessary, a 10-ampere cord should be used. Cords

rated for less amperage may overheat. Care should be taken to arrange the cord so

that it cannot be pulled or tripped over.

Know Your Iron

Parts and Features

1. Water Fill Cover

2. Accu-Spray Nozzle

3. Blast of Steam Button

4. Spray Button

5. Self Clean/Temperature/

Steam Dial

6. Auto Shutoff Reset Button/Light

7. Swivel Cord*

8. Fabric Setting Guide

9. Retractable Cord*

10. Cord Release Button

11. Iron Guard Soleplate Cover*

* Selected features not available on

all models.

Before First Use

Please read Important Safeguards and Consumer Safety Information.

VERY IMPORTANT

1. Plug iron into electrical outlet. The

Auto Shutoff Reset Button/Light will

come on. If the plug will not fit, read

about the polarized plug in

“Consumer Safety Information.”

2. Turn the Temperature/Steam Dial to

a setting in the Dry

Iron range. As an

example, the illus-

tration shows the

iron set at 2

(Nylon).

3. Preheat for about 4 minutes

before beginning to iron.

4. The iron will automatically shut off

1 hour after the iron is plugged in

and the Auto Shutoff Reset Button/

Light will go out. To turn the iron

back on, press the Auto Shutoff

Reset Button/Light located on the

top of the handle.

5. When finished ironing, turn the

Temperature/

Steam Dial to OFF

(0)and unplug

iron.

Using Your Iron

Read and follow instructions above in “Before First Use.”

To Dry Iron

The steam vents on the soleplate must

be cleaned before first use. Follow

instructions in the “Self Clean II

System” section. This will assure steam

vents have been thoroughly cleaned.

Remove any peel off labels from the

iron and wipe any manufacturing

residue from the soleplate and vents.

During the first use of the iron, it may

appear to smoke. This will stop and

does not indicate a defect or hazard.

CAUTION: Some irons spit or sputter

water during the first few uses. This

happens as the steam chamber

becomes conditioned. This will stop

after a few uses.

1. Fill water tank following instructions

in “Filling the Water Tank.”

2. Plug iron into electrical outlet. The

Auto Shutoff Reset Button/Light will

come on. If the plug will not fit, read

about the polarized plug in

“Consumer Safety Information.”

3. Turn the Temperature/Steam Dial to

a setting in the

Steam Iron range.

As an example, the

illustration shows

the iron set at 7

(Rayon).

4. Preheat for about 4 minutes

before beginning to iron.

5. The iron will automatically shut off

1 hour after the iron is plugged in

and the Auto Shutoff Reset Button/

Light will go out. To turn the iron

back on, press the Auto Shutoff

Reset Button/Light located on the

top of the handle.

6. When finished ironing, turn the

Temperature/

Steam Dial to

OFF (0)and

unplug iron. Allow

to cool and empty

water from water

tank. See “Storing

Your Iron.”

To Steam Iron

1. Make sure iron is unplugged.

2. Regular tap water may be used.

In areas with extremely hard water,

the use of distilled or filtered water is

highly recommended.

3. Slide open Water Fill Cover.

4. Slowly pour water into water fill

opening until water level reaches

the top of the Water Window.

Never overfill.

NOTE: Never place anything in your

iron except water.

To order our Water Filter Cup for irons,

call the toll-free customer service

number listed on the front cover.

Water

Window

Filling the Water Tank

1. Fill the water tank with water

(5 oz/130 ml).

2. Plug in iron and turn Temperature/

Steam Dial to highest setting.

Let iron preheat 4 minutes.

3. Leave Temperature/Steam Dial at

highest setting and

unplug iron. Hold

iron in ironing

position over a

sink. Repeatedly

push the Blast of

Steam Button to

aid in the cleaning process.

4. Be careful. Steam and hot water will

pour out of the steam vents. This

cleans the vents. Allow all water to

empty from the water tank. This will

take about two minutes.

Self Clean II System

5. Do not use salt, vinegar, or

commercial iron cleaners to clean

the inside of the iron.

6. Turn Temperature/Steam Dial to OFF

(0). This cleans the

steam valve inside

the iron.

1. The timing of the automatic shutoff

starts when the iron is plugged in.

The Auto Shutoff Reset Button/Light

will come on.

2. About 1 hour after the iron is plugged

in, the light in the Auto Shutoff Reset

Button will go out which means the

iron has automatically shut off.

3. Press the Auto Shutoff Reset

Button/Light. This will turn the iron

on for another hour and the light will

come back on.

4. If the iron is plugged in and the

Temperature/Steam Dial is turned

to OFF (0), the automatic shutoff is

still activated.

Features

Auto Shutoff Reset Button/Light

Auto Shutoff

Reset Button

Blast of Steam & Spray

1. To use blast of steam, the

Temperature/Steam Dial must be

set in the steam range.

2. To get a blast of steam, press the

Blast of Steam

Button. Do not

press button con-

tinuously. Press

once every two

seconds. Some

time is needed for

the iron to create the steam. Please

use iron carefully, as steam is hot

and can cause burns or serious

injury.

3. To spray a mist of water, press

the Spray Button to

dampen wrinkles

that are difficult to

remove.

Blast of

Steam

Spray

Retractable Cord (not available on all models)

1. Press and hold the Cord Release

Button while pulling cord to desired

length. Do not unwind cord beyond

indicator on cord.

2. To store cord, place the iron, sole-

plate down, on ironing board.

Unlatch Retractable Cord Handle

and wind clockwise.

IMPORTANT! Do not press Cord

Release Button while winding cord.

Only wind clockwise or the cord may

jam. See illustration.

3. If cord jams while winding, push the

Cord Release Button to unwind

slightly until cord is free. Then slowly

start to wind clockwise again.

Cord

Release

Button

Wind

clockwise

Iron Guard Soleplate Cover (not available on all models)

If Retractable Cord Handle

comes off, it is designed to snap

back in place.

1. Place pins of handle into slots

in reel. See illustration.

2. Lift handle up until it snaps in place.

There is no need to wait for the iron to

cool before storing. Make sure the iron

has been turned off and unplugged.

Place the Iron Guard soleplate cover

on the iron immediately after ironing.

CAUTION: The soleplate may be hot,

so care must be used in placing the

cover on the soleplate.

Retractable

Cord

Handle

1. When finished ironing, turn the

Temperature

Control Dial to

OFF (0)and

unplug iron. Set

iron on its heel

and let cool.

NOTE: If you have the Iron Guard

Soleplate Cover, you can store the hot

iron immediately.

2. Empty all water in iron. If the water is

not emptied, it may

interact with the

metal of the iron

and cause the

water to discolor.

This will result in

Storing Your Iron

steam and water droplets discoloring

clothing. Carefully hold iron over sink

with water tank opening aimed down.

Let all water drain out.

3. To clean the soleplate wipe with a

wet cloth and dish detergent.

Wipe clean with a damp cloth. Do

not use abrasive cleaners.

CAUTION: Be sure iron is cool prior

to cleaning.

4. To maintain good steam production,

clean the iron periodically using the

self-clean setting described in the

“Self Clean II System” section.

SETTING IRONING INSTRUCTIONS

Dry iron on the wrong side of the fabric.

Dry iron; use spray if necessary.

Iron on the wrong side of the fabric.

Use a pressing cloth and steam iron on the

wrong side of the fabric.

Iron while fabric is still damp.

Iron on the wrong side of the fabric.

Iron while still damp using steam and spray

if necessary.

Iron while still damp on the wrong side

of the fabric.

Dry Iron

TO IRON

Off/Clean

Acetate

Nylon

Acrylic

Silk

Wool

Polyester

Rayon

Cotton

Linen

Steam Range

NOTE: To dry iron on settings 4-9, empty all water from the tank.

Temperature Control Dial and

Fabric/Setting Chart

store the cord as described in the

“Retractable Cord” section. Never

store iron sitting flat on the soleplate.

This would damage the inside of the

soleplate. Always store iron on its heel

in upright position.

5. Wrap cord loosely around cord wrap

and set on heel. If

you have the

retractable cord

feature, use the

reel to wind and

Ironing Tips

• Always check the fabric content

before beginning to iron. If the fabric

is a blend, use the lower temperature

setting.

• If the fabric content is unknown, use

the lowest temperature setting and

test on an inside seam of the garment.

• If ironing several items, start ironing

the items which need the lowest

temperature setting first. An iron heats

up much faster than it cools down.

• To maintain the quality of the

soleplate, never iron over zippers,

pins, buttons or anything metal.

• Use caution when ironing around

plastic buttons and zippers as these

may melt.

• To iron fabrics stating “Dry Clean

Only,” first clean as directed before

ironing. Use caution and begin

ironing on the lowest setting, testing

on an inside seam allowance of

the garment.

QUESTION

Iron won’t heat.

Water is leaking

out of the iron.

Iron won’t steam.

Iron leaves spots

on clothing.

Cord is twisted.

Troubleshooting

ANSWER

1. Is the iron plugged in and the Auto Shutoff Reset

Button/Light on?

2. If the iron is plugged in and the power light is not on,

check the outlet by plugging in a lamp.

3. Is the Temperature/Steam Dial turned to a fabric setting?

4. If auto shutoff model, is the Auto Shutoff Reset Button

light on? If not, press Auto Shutoff Reset Button/Light,

located on the top of the handle, to turn the iron back on.

1. If you over filled the water tank, empty some water.

2. If you are steam ironing, is the Temperature/Steam Dial

in the steam range and did the iron have enough time

to preheat?

3. If you’ve been ironing for more than one hour the auto

shutoff may have turned the iron off. Press the Auto

Shutoff Reset Button/Light, located on the top of the

handle, to turn the iron back on.

1. Is there water in the water tank?

2. Is the Temperature/Steam Dial set in the steam range?

3. Has the iron had enough time to preheat?

4. Has the iron been cleaned with the self-clean feature?

The steam vents may be blocked.

1. ALWAYS empty the water tank of the iron after using.

Water left in the tank may discolor.

2. Clean the steam vents as instructed in the “Self

Clean II System” section.

1. If the iron cord should become twisted, unplug iron and

let cool. Hold iron cord in the middle of entire length. Let

plug and iron dangle freely until cord uncoils. This will

extend the life of your iron cord.

Indice

Altri manuali Hamilton Beach Ferro

Hamilton Beach

Hamilton Beach Easy Touch Iron Manuale utente

Hamilton Beach

Hamilton Beach Durathon 19900-CN Manuale utente

Hamilton Beach

Hamilton Beach 14671 Manuale del proprietario

Hamilton Beach

Hamilton Beach Pro SteamMax HB608WB Manuale utente

Hamilton Beach

Hamilton Beach 10092 Manuale del proprietario

Hamilton Beach

Hamilton Beach 840124300 Manuale utente

Hamilton Beach

Hamilton Beach Easy-Touch 14417 Foglio di istruzioni

Hamilton Beach

Hamilton Beach 840111900 Manuale utente

Hamilton Beach

Hamilton Beach 19804 Manuale del proprietario

Hamilton Beach

Hamilton Beach 14515R Manuale utente

Hamilton Beach

Hamilton Beach 840129100 Manuale utente

Hamilton Beach

Hamilton Beach 14565 - Lightweight Iron Manuale del proprietario

Hamilton Beach

Hamilton Beach 14010 Manuale del proprietario

Hamilton Beach

Hamilton Beach 14X60 - Expression Ergonomic Handle Iron Manuale utente

Hamilton Beach

Hamilton Beach QuickGlide 14353 Foglio di istruzioni

Hamilton Beach

Hamilton Beach 14690 Manuale del proprietario

Hamilton Beach

Hamilton Beach 14960 Manuale utente

Hamilton Beach

Hamilton Beach 14401 Manuale utente

Hamilton Beach

Hamilton Beach 14506 Manuale del proprietario

Hamilton Beach

Hamilton Beach 840164201 Manuale utente

Hamilton Beach

Hamilton Beach Durathon 19803 Manuale del proprietario

Hamilton Beach

Hamilton Beach 14210 Manuale del proprietario

Hamilton Beach

Hamilton Beach 14200 - Nonstick Auto-Off Retro Steam Iron Manuale utente

Hamilton Beach

Hamilton Beach Hamilton Beach Manuale utente

Manuali Ferro popolari di altre marche

Clatronic

Clatronic DB 3703 Manuale utente

TEFAL

TEFAL FV4093Z0 Manuale utente

Gorenje

Gorenje SIH 2200 BS Manuale utente

Philips

Philips GC6012 Manuale utente

Bosch

Bosch 2 Series Manuale utente

Riffel

Riffel Catena KB-819 Manuale utente

Texi

Texi Hestia Manuale utente

Maxwell

Maxwell MW-3010 Manuale utente

TREVIDEA

TREVIDEA Girmi ST60 Manuale utente

Philips

Philips HI5914/30 Manuale utente

Primula

Primula Vapormat Manuale utente

Magio

Magio MG-541 Manuale utente

Scarlett

Scarlett SC-1334S Manuale utente

Bosch

Bosch Sensixx B22L Manuale utente

Philips

Philips GC651 Manuale utente

Vitek

Vitek VT-1247 VT Manuale utente

Cleanmaxx

Cleanmaxx 3397 Manuale utente

Philips

Philips GC800 Manuale utente