Hioki 3286 Manuale utente

POWER HiTESTER

CLAMP ON

INSTRUCTION MANUAL

3286

Contents

Introduction i

Shipping Check ii

Safety iii

Attentions During Use vii

Organization of This Manual xii

Chapter 1 Product Outline 1

1.1 Product Outline 1

1.2 Features 2

1.3 Parts and Functions 3

1.4 Flowchart of Key Operations 9

1.4.1 Current Measurements Mode 9

1.4.2 Harmonic Measurement 11

1.4.3 Change the Range 11

Chapter 2 Measurement Procedure 13

2.1 Preparations 13

2.2 Connections 14

2.3 Range Setup 20

2.4 Power Measurement 21

2.4.1 1φ

φφ

φP Meter, 1φ

φφ

φPF Meter and 3φ

φφ

φPF Meter 22

2.4.2 Power and Power Factor 25

2.4.3 Phase Detection 27

2.4.4 Current 28

2.4.5 Voltage 29

2.5 Harmonic Measurement 30

2.5.1 Current Harmonics 30

2.5.2 Voltage Harmonics 32

2.6 Data Hold Function HOLD 33

2.7 SLOW Mode 33

2.8 Recording Function REC 33

2.9 SETUP Function 35

2.10 Measurement Condition Save Function 36

2.11 Auto Power-Off Function APS 37

2.12 Battery Low Warning 37

2.13 Beep Tone 37

2.14 DATA OUTPUT 38

Chapter 3 Specifications 39

3.1 Measurement Specifications

(23 5, 80% RH max.) 39

3.1.1 AC Current Measurement Specifications 39

3.1.2 AC Voltage Measurement Specifications 40

3.1.3 Specifications of Single-phase Power

Measurement 1φ

φφ

φPMeter 41

3.1.4 Specifications of Power Factor

and Phase Angle Measurements

1φ

φφ

φPF Meter and 3φ

φφ

φPF Meter 42

3.1.5 Specifications of Balanced Three-phase

Power Measurements 43

3.1.6 Specifications of Frequency Measurement 44

3.1.7 Specifications of Harmonic Measurement 44

3.2 General Specifications 45

3.3 Operation Expressions 48

Chapter 4 Battery Replacement 51

Chapter 5 Attaching The Hand Strap 53

Chapter 6 Troubleshooting 55

Chapter 7 Service 57

Introduction

Thank you for purchasing this HIOKI "3286

CLAMP ON POWER HiTESTER." To get the

maximum performance from the product, please read

this manual first, and keep this at hand.

Importance

This product is the clamp on power meter which

keeps measurement function of the multiple

functions. If you set up a function mode in

advance, the mode will start up from the next use.

Have it set up for the preferable use. (Refer to "2.10

Measurement Condition Save Function)

Request

We have tried to bring this manual as close to

perfection as we could achieve. If perchance you

find any unclear portions, mistakes, omissions, or

the like, we would be most obliged if you could

please notify us of them via any HIOKI agent, or

directly.

Shipping Check

When you receive the product, inspect it carefully to

ensure that no damage occurred during shipping. In

particular, check the accessories, panel switches, and

connectors.

If damage is evident, or if it fails to operate

according to the specifications, contact your dealer

or HIOKI representative.

Check the 3286 Unit and the Supplied

Accessories

Main unit

3286 CLAMP ON POWER HiTESTER

Supplied accessories

9355 Carrying Case 1

9635 Voltage cord 1

Hand Strap 1

Battery 6LF22 alkaline battery 1

Instruction manual 1

Options

9636 RS-232C CABLE

9636-01 RS-232C PACKAGE

9442 PRINTER (DPU-414, Seiko Instrument Inc.)

iii

Safety

DANGER

This equipment is designed according to IEC

61010 Safety Standards, and has been tested for

safety prior to shipment. Incorrect measurement

procedures could result in injury or death, as

well as damage to the equipment. Please read

this manual carefully and be sure that you

understand its contents before using the

equipment. The manufacturer disclaims all

responsibility for any accident or injury except

that resulting due to defect in its product.

Safety

This manual contains information and warnings

essential for safe operation of the product and for

maintaining it in safe operating condition. Before

using the product, be sure to carefully read the

following safety notes.

Safety

DANGER

Indicates that incorrect operation

presents extreme danger of accident

resulting in death or serious injury to the

user.

WARNING

Indicates that incorrect operation

presents significant danger of accident

resulting in death or serious injury to the

user.

CAUTION Indicates that incorrect operation

presents possibility of injury to the user

or damage to the equipment.

NOTE Denotes items of advice related to

performance of the equipment or to its

correct operation.

The symbol printed on the product

indicates that the user should refer to a

corresponding topic in the manual (marked

with the symbol) before using the

relevant function. In the manual, the

symbol indicates particularly important

information that the user should read

before using the product.

Indicates AC (Alternating Current).

Indicates DC (Direct Current).

Indicates a device which is double-

insulated.

The following symbols in this manual indicate the

relative importance of cautions and warnings.

Safety Symbols

Safety

We define measurement tolerances in terms of rdg.

(reading) and dgt. (digit) values, with the following

meanings:

rdg. (reading or displayed value)

The value currently being measured and indicated

on the measuring product.

dgt. (resolution)

The smallest displayable unit on a digital measuring

product, i.e., the input value that causes the digital

display to show a "1".

Overvoltage Categories

To ensure safe use of measurement, IEC 60664

establishes safety level standards for different

locations, classified as CAT I through CAT IV, and

called overvoltage categories. These are defined as

follows.

CAT I: Secondary electrical circuits that are

connected to a wall outlet through a

transformer or similar device.

CAT II: Primary electrical circuits in equipment

connected to a wall outlet via a power

cord (portable tools, household appliances,

etc.)

CAT III: Primary electrical circuits of heavy

equipment (fixed installations) connected

directly to the distribution panel, and

feeders between the distribution panel and

outlets.

CAT IV: The circuit from the service drop to the

service entrance, then to the power meter

and to the primary overcurrent protection

device.

Safety

Higher-numbered categories correspond to electrical

environments with greater momentary energy, so a

measurement device designed for CAT III

environments can endure greater momentary energy

than a device designed for CAT II. Use of a lower

category product in a higher category environment

could result in a severe accident and must be

carefully avoided.

vii

Attentions During Use

DANGER

To avoid short circuits and potentially life-

threatening hazards, never attach the clamp to a

circuit that operates at more than the maximum

rated voltage / 600V, or over bare conductors.

Clamp-on probe should only be connected to

the secondary side of a breaker, so the breaker

can prevent an accident if a short circuit occurs.

Connections should never be made to the

primary side of a breaker, because unrestricted

current flow could cause a serious accident if a

short circuit occurs.

WARNING

To avoid electric shock, do not allow the

product to get wet, and do not use it when your

hands are wet.

To avoid electric shock when measuring live

lines, wear appropriate protective gear, such as

insulated rubber gloves, boots and a safety

helmet.

Attentions During Use

Follow these precautions to ensure safe operation

and to obtain the full benefits of the various

functions.

Indice

Altri manuali Hioki Apparecchiature di prova

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente