Honeywell 3820 Manuale utente

3820, 3820i, 4820, 4820i

Cordless Imaging Systems

Quick Start Guide

CRDLSS-02-QS Rev F

1/12

Aller à www.honeywellaidc.com pour le français.

Vai a www.honeywellaidc.com per l'italiano.

Gehe zu www.honeywellaidc.com für Deutsch.

Ir a www.honeywellaidc.com para español.

日本語 : www.honeywellaidc.com をご覧ください。

如要到中国 www.honeywellaidc.com（简体）。

查看繁体版请登陆 www.honeywellaidc.com

한글 www.honeywellaidc.com 로이동합니다 .

Note: Refer to your user’s guide for information about cleaning your

device.

For localized language versions of this document, go to

www.honeywellaidc.com.

Getting Started

Turn off the computer’s power before connecting the base, then

power up the computer once the base is fully connected. When the

base is connected and powered up, put the imager in the base to

establish a link. The green LED on the base flashes to indicate the

imager’s battery is charging.

USB Connection

Keyboard Wedge Connection

Serial (RS-232) Connection

Reading Techniques

The view finder projects an aiming

beam that should be centered over

the bar code. (The 4820/4820i can

be positioned in any direction for a

good read.)

Hold the imager over the bar code,

pull the trigger, and center the

aiming beam on the bar code.

The aiming beam is smaller when

the imager is closer to the code and larger when it is farther from the

code. Hold the imager close to smaller bar codes, and farther away

from large bar codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need to

tilt the imager at an angle so the bar code can be scanned.

4820/4820i

can read in

any direction

Center

beam over

bar code

Note: If the imager beeps 3 times when scanning a bar code, the link

has not been established. If the imager beeps once, the link

has been established.

Standard Product Defaults

This bar code resets all standard product default settings.

Standard Product Defaults

PC Interface

Scan the bar code that describes the PC or interface you are using.

RS-232

USB Keyboard (PC)

Japan DOS/V

USB Japanese Keyboard

(PC)

Emulate External Keyboard

AT/PS2 Keyboard Wedge

(Default)

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan

the numeric bar code(s) from the back of this sheet, then the Save

bar code to program the keyboard for your country. As a general

rule, the following characters are not supported by the imager for

countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~.

Note: For complete list of country codes, see the User’s Guide for

your product at our website, www.honeywellaidc.com.

Country Code Scan Country Code Scan

Belgium 1Italy 5

Denmark 8Norway 9

Finland 2Spain 10

France 3Switzerland 6

Germany/Austria 4USA (Default) 0

Great Britain 7

Program Keyboard Country

Save

Open Link

Scan the Open Link bar code, then place the imager into the base to

establish a link. Placing a different imager into the base establishes

a new link and the old imager is unlinked.

Override Locked Imager

If you need to replace a broken or lost imager that is linked to a base,

scan the Override Locked Imager bar code with a new imager, and

place that imager in the base. The locked link will be overridden; the

broken or lost imager’s link with the base will be removed, and the

new imager will be linked.

Unlinking the Imager

If the base has an imager linked to it, that imager must be unlinked

before a new imager can be linked. Once the previous imager is

unlinked, it will no longer communicate with the base. Scan the

Unlink Imager bar code to unlink an imager.

Open Link

Override Locked Imager

Unlink Imager

Trigger

The following bar codes will allow you to use the reader in Manual

Trigger mode (need to press the trigger to read) or Presentation

mode (the reader is activated when it “sees” a bar code).

Streaming Presentation™ (4820/4820i)

Note: Streaming presentation mode applies only to units with

advanced illumination. Units with advanced illumination have

a software revision of 31205481-027 or higher.

When in Streaming Presentation mode, the imager leaves the scan

illumination on all the time and continuously searches for bar codes.

Manual Trigger

(Default)

Presentation Mode

Streaming Presentation Mode

Reread Delay

This sets the time period before the imager can read the

same

bar

code a second time. Setting a reread delay protects against

accidental rereads of the same bar code.

Suffix

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code. To add a tab after the bar code, scan the Add Tab

Suffix bar code. Otherwise, scan the Remove Suffix bar code to

remove the suffixes.

Medium Reread Delay

Add CR Suffix

Remove Suffix

Add Tab Suffix

Altri manuali per 3820

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Honeywell Lettore di codici a barre

Honeywell

Honeywell Solaris MS7820 Manuale utente

Honeywell

Honeywell Voyager 9520/40 Manuale utente

Honeywell

Honeywell MS4980 Manuale utente

Honeywell

Honeywell MX7 Tecton Manuale utente

Honeywell

Honeywell 4820HDHM Manuale utente

Honeywell

Honeywell Vuquest 3320g Manuale utente

Honeywell

Honeywell 1400gPDF Manuale utente

Honeywell

Honeywell I-Class Mark II Manuale utente

Honeywell

Honeywell Voyager 1450g Series Manuale utente

Honeywell

Honeywell 2020 Manuale utente

Honeywell

Honeywell Voyager 1450g Series Manuale utente

Honeywell

Honeywell XL 800 Series Manuale utente

Honeywell

Honeywell Hyperion 1300G Manuale utente

Honeywell

Honeywell VOYAGER 1200G Manuale utente

Honeywell

Honeywell SF61 Manuale utente

Honeywell

Honeywell Quantum T 3580 Manuale utente

Honeywell

Honeywell QUANTUME IS3480 Manuale utente

Honeywell

Honeywell CM4680 Manuale utente

Honeywell

Honeywell MS2421 Manuale utente

Honeywell

Honeywell Vuquest 3310g Manuale utente

Honeywell

Honeywell VoyagerGS 9590 Series Manuale utente

Honeywell

Honeywell 4820HDHM Manuale utente

Honeywell

Honeywell IS4921 Guida rapida alla configurazione

Honeywell

Honeywell DCS19W Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente