Honeywell DR 4300 Guida

Form 43-DR-33-74 Page 1 of 3

Model DR 4300

Circular Chart Recorder

Replacement Instruction

Display Module Printed Circuit Assembly (51404459-501)

Document Number Form: 43-DR-33-74

Effective: 3/98

Supersedes: None

Kit Contents This Display Module Printed Circuit Assembly (PCA) Kit contains the

following parts:

•Display PCA

•#6 x 3/8 Plastite Screws (2)

•Cables (2)

Summary Enclosed are a new display module PCA and parts for your DR4300

recorder. Use the following procedure to install the new display module.

WARNING Never access components inside the case with power applied.

Continued next page

Kit Instruction, continued

Page 2 of 3 Form 43-DR-33-74

Component Location Refer to Figure 1 for the component locations and Table 1 for the

installation procedure.

24229

Screws

Display

ModulePCA

Cable

Pen 2

Cable

Pen 1

Figure 1 – Component Location

Kit Instruction, continued

Form 44-DR-33-74 Page 3 of 3

Installation Procedure Follow the procedure in Table 1 to install the new display module PCA in

your recorder.

Table 1 – Display Module Printed Circuit Assembly Installation

Step Action

1Power down the recorder. Open the chart door and swing the chart

plate out.

2 Note cable orientation before removing the two screws holding the

display module PCA to the top of the case.

3 Disconnect cable(s) from the back side of old PCA. Pull outward

on the connector’s end tabs then pull out the ribbon cable(s).

You can leave the cable(s) attached to J4 on the main PCA(s)

unless you are also replacing the cable. If you are replacing the

cable(s), disconnect each one from J4 on its specific PCA and

remove it, noting the routing layout.

4 Install the cable(s) on the new display PCA. Insert the cable in the

connector and push in on end of connector tabs to lock cable(s) in

place.

If you are replacing the cable(s), go to Step 5.

If you are using the existing cable(s), go to Step 6.

5 Feed the pen 1 ribbon cable behind the transmitter power

assembly, behind the Main PCA for pen 1 (right side of case) to its

J4 connector (upper right corner).

If applicable, run the pen 2 ribbon cable behind the transmitter

power assembly, behind the pen 1 Main PCA, bringing it to the J4

connector on the Main PCA for pen 2 (left side of case). This

ribbon should be on top of the pen 1 ribbon cable.

6 Secure the new display PCA to the case with the screws provided.

7 Close the chart plate and apply power. Check for normal display

indication.

Indice

Altri manuali Honeywell Strumento di misura

Honeywell

Honeywell FlexLine SmartServo 954 Manuale utente

Honeywell

Honeywell Q4000 Manuale utente

Honeywell

Honeywell SX Manuale utente

Honeywell

Honeywell Vertex M Nota di rilascio

Honeywell

Honeywell enCore Series Manuale utente

Honeywell

Honeywell Class 320 Meter Manuale utente

Honeywell

Honeywell Limitless WPMM Series Manuale utente

Honeywell

Honeywell E-Mon KWH Manuale utente

Honeywell

Honeywell FS20X Series Manuale utente

Honeywell

Honeywell BK V2 Manuale utente

Honeywell

Honeywell MicroMAX Pro Istruzioni operative

Honeywell

Honeywell X4 Series Istruzioni per l’uso

Honeywell

Honeywell COCON 26 DRA-LP/MP Manuale utente

Honeywell

Honeywell 90DM4 Manuale utente

Honeywell

Honeywell QX Series Manuale utente

Honeywell

Honeywell SmartLine SLG 700 Manuale utente

Honeywell

Honeywell enCore FC Series Manuale utente

Honeywell

Honeywell QX Manuale utente

Honeywell

Honeywell EW44*A Series Manuale

Honeywell

Honeywell TS34C Manuale utente

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Manuale utente

Honeywell

Honeywell UDA2182 Guida all'installazione

Honeywell

Honeywell Elster EK280 Istruzioni per l’uso

Honeywell

Honeywell AS302P Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente