HP 64782 Manuale utente

Installation/Service/Terminal Interface Guide

HP 64782

MC6833x Emulator/Analyzer

Notice

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose. Hewlett-Packard shall not be liable for errors

contained herein or for incidental or consequential damages in connection with the

furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information, which is protected by copyright.

All rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without the prior written consent of

Hewlett-Packard Company. The information contained in this document is subject

to change without notice.

HP is a trademark of Hewlett-Packard Company.

UNIX is a registered trademark of UNIX System Laboratories Inc. in the U.S.A.

Hewlett-Packard Company

P.O. Box 2197

1900 Garden of the Gods Road

Colorado Springs, CO 80901-2197, U.S.A.

RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by the U.S.

Government is subject to restrictions set forth in subparagraph (C) (1) (ii) of the

Rights in Technical Data and Computer Software Clause at DFARS 252.227-7013.

Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A.

Rights for non-DOD U.S. Government Departments and Agencies are as set forth

in FAR 52.227-19(c)(1,2).

Printing History

New editions are complete revisions of the manual. Many product updates and

fixes do not require manual changes, and manual corrections may be done without

accompanying product changes. Therefore, do not expect a one-to-one

correspondence between product updates and manual revisions.

Edition 1

Edition 2

Edition 3

64782-97000, August 1994

64782-97001, September 1996

64782-97002, November 1996

Edition 4 64782-97003, April 1997

Safety and Certification and Warranty

Safety information, and certification and warranty information can be found at the

end of this manual on the pages before the back cover.

iii

The HP 64782 Emulator

Description

The Hewlett-Packard Model 64782 emulator supports the Motorola 6833x

microprocessor family. The emulators and supported microprocessors include

HP 64782B/MC68331, HP 64782C/MC68332, HP 64782E/MC68334,

HP 64782G/MC68336, and HP 64782J/MC68338. In this manual, the HP

emulators are referred to by Model Number 64782, and the Motorola

microprocessors are referred to by MC6833x, except where specific information

applies only to certain individual members of the emulator/microprocessor family.

The emulator supports clock speeds up to 33 MHz.

The emulator supports both 5V and 3.3V operation. The emulator has a PGA-style

connector. It can be plugged directly into the PGA connector on the demo board,

and it can be plugged into a PQFP or TQFP target system using optional

accessories.

The emulator plugs into the modular HP 64700 instrumentation card cage and

offers 64 channels of processor bus analysis with the HP 64794A or HP 64704A

emulation-bus analyzer. Up to eight megabytes of emulation memory may be

installed on the probe. High performance download is achieved through the use of

an optional LAN or RS-422 interface. A pair of RS-232 ports and a

firmware-resident interface allow debugging of a target system at remote locations.

For software development, the HP AxCASE environment is available on SUN

SPARCsystems and on HP workstations. This environment includes an ANSI

standard C compiler, assembler/linker, a debugger, the HP Software Performance

Analyzer that allows you to optimize your product software, and the HP Branch

Validator for test suite verification. The C compiler, assembler/linker, and

debugger are also available for MS-DOS systems.

Language support is also available from several third-party vendors. This capability

is provided through the HP 64700’s ability to consume several industry standard

output file formats.

Ada language support is provided on HP 9000 workstations by third-party vendors

such as Alsys and Verdix. An Ada application developer can use the HP emulator

and any compiler that generates HP/MRI IEEE-695 to do exhaustive, real-time

debugging in-circuit or out-of-circuit.

Features

HP 64782 Emulator

•Active probe emulator; supports the fastest processor speeds currently

available. At the time this manual was printed, the emulator had been tested to

the following processor speeds:

–20 MHz for MC68331, MC68332, and MC68334.

–16 MHz for MC68336 and MC68338.

•5V and 3.3V operation

•No wait states to target memory

•Fast termination cycles to target memory

•Unlimited software breakpoints

•Symbolic support

•36 inch cable and 219 mm (8.8") x 102 mm (4") probe

•Background and foreground monitors

•Simulated I/O with workstation interfaces

•Consumes IEEE-695, HP-OMF, Motorola S-Records, and Extended Tek Hex

File formats directly. (Symbols are available with IEEE-695 and HP-OMF

formats.)

•Multiprocessor emulation

–synchronous start of 32 emulation sessions

–cross triggerable from another emulator, logic analyzer, or oscilloscope

•Demo board and self test module included

Emulation-bus analyzer

•64-channel emulation-bus analyzer

•Post-processed dequeued trace with symbols

•Eight events, each consisting of address, status, and data comparators

•Events may be sequenced eight levels deep and can be used for complex

trigger qualification and selective store

Emulation memory

•Up to 8 Mbytes of emulation memory

•All emulation memory is dual-ported

•Mapping resolution is 256 bytes

•The wait states required for emulation memory depend on processor speed and

the access speeds of the SIMMs installed on the emulation probe, as shown

below:

SIMM Access Speed Runs with no Wait

States Requires 1 Wait State

35 nSEC 0 to 16.78 MHz 16.78 MHz to 25 MHz

20 nSEC 0 to 25 MHz 25 MHz to 33 MHz

25 nSEC 0 to 22 MHz 22 MHz to 30 MHz

•Fast termination cycles to emulation memory are supported up to 10 MHz

when using 20-nSEC and 25-nSEC SIMMs, and supported up to 8 MHz when

using 35-nSEC SIMMs

vii

In This Book

This manual covers the Hewlett-Packard Model 64782 emulator for the Motorola

MC6833x family of microprocessors. It is divided into the following parts:

Part 1, “Installation,” shows you how to install and connect all of the

emulator/analyzer hardware in the card cage, connect the card cage to a host

computer in several typical configurations, and connect the emulator probe into the

demo board and into your target system.

Part 2, “Service,” shows you how to install and update emulator/analyzer firmware,

solve problems you may encounter while using the emulator/analyzer, and obtain

replacement parts for the emulator/analyzer from Hewlett-Packard.

Part 3, “Terminal Interface Reference,” introduces the interfaces available to use

with the emulator/analyzer, and shows you how to use the terminal interface for the

emulator/analyzer.

This manual replaces the Terminal Interface Reference which accompanied earlier

HP emulators. For information on the Terminal Interface, see Part 3.

You should read the book Concepts of Emulation and Analysis when you have the

chance to do so; it contains a good conceptual introduction to the emulation

process, and also describes how an emulation monitor works. Another book, the

HP 64700 Card Cage Installation/Service Guide, tells you more about installation

and configuration of the HP 64700 Card Cage. If you have a problem with the

emulator and don’t understand how to fix it, a listing of HP Sales and Service

offices is in the Support Services Guide in the back of this binder.

viii

Contents

Part 1 Installation Guide

1 Preparing the Emulator

Preparing the Emulator 4

What you need 5

Antistatic precautions 6

Step 1. Install optional memory modules on Deep Analyzer card (if using the Deep

Analyzer) 7

Observe antistatic precautions 7

Step 2. Connect the Emulator Probe Cables 9

Step 3. Install Boards into the HP 64700 Card Cage 11

Step 4. Install emulation memory modules on emulator probe 24

Step 5. Connect the power cord 28

2 Connecting to a Host Computer

Step 1: Choose a system configuration 172

Step 2: Connect the LAN cable 172

Step 3: Install host software 173

Step 4: Configure the LAN parameters 174

To configure LAN parameters using "ipconfig700" 175

To configure LAN parameters using the terminal interface 178

If "telnet" does not access the emulator 181

3 Connecting to the Demo Board

Installation 44

Step 1. Connect the emulator probe to the demo target system 45

Step 2. Apply power to the HP 64700 47

Step 3. Verify the performance of the emulator 48

4 Connecting the Emulator to a Target System

Plugging The Emulator Into A Target System 50

Understanding an emulator 50

Target system design 50

Buffering and AC specifications 51

DC specifications 51

Clocks 51

Target power 52

Equivalent circuits 53

Connecting the emulator to the target system 56

Verifying Operation Of The Emulator In Your Target System 61

Additional equipment 61

Probing 61

Selecting a clock source 62

Running the emulator configured like the processor 62

To verify operation of the target system 64

Interpreting the trace list 68

Fixing timing problems 71

Installing the emulator in a target system without known good software 71

Installing Emulator Features 74

Evaluating the reset facilities 74

Installing the background monitor 76

Resetting into the background monitor 76

Testing memory accesses with the background monitor 77

Running a program from the background monitor 78

Breaking into the background monitor 79

Exiting the background monitor 79

Software breakpoint entry into the background monitor 80

Stepping with the background monitor 80

Installing the foreground monitor 81

Resetting into the foreground monitor 82

Dealing with keep-alive circuitry by using the custom foreground monitor 83

Testing memory access with the foreground monitor 84

Running a program from the foreground monitor 85

Breaking into the foreground monitor 86

Exiting the foreground monitor 86

Software breakpoint entry into the foreground monitor 87

Stepping with the foreground monitor 87

Installing emulation memory 87

Contents

Altri manuali per 64782

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali HP Hardware per computer

HP AB479A Manuale utente

HP 3000 Series Manuale

HP HPE LSWM2XGT2PM Manuale utente

HP WL110 - Wireless PC Card Manuale utente

HP 381513-B21 - Smart Array P800 Controller... Manuale utente

HP Wireless USB Network Adapter hn215w Manuale utente

HP E3473A Manuale utente

HP Xw4600 - Workstation - 2 GB RAM Manuale utente

HP t730 Thin Client Manuale utente

HP Integrity rx1600 Manuale utente

HP NC550SFP Manuale utente

HP A4800A Guida

HP Smart Array P400 Istruzioni utente

HP OmniBook 3100 Manuale utente

HP 6600 FIP-20 Flex Istruzioni per il montaggio

HP D7171A - NetServer - LPr Manuale utente

HP MCS G2 Guida all'installazione

HP Model 744 - VME Workstation Manuale utente

HP QMH2672 Manuale utente

HP StorageWorks XP128 Manuale utente

HP 8168E Manuale utente

HP Xw8400 - Workstation - 4 GB RAM Manuale utente

HP Nc6400 - Compaq Business Notebook Manuale utente

HP 705 Guida rapida

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente