HP Broadband Service Analyzer Manuale utente

Broadband Service Analyzer

Setting Up the

25.6 Mb/s Interface Pod

The information contained in this document is subject to change without notice.

TO THE EXTENT ALLOWED BY LOCAL LAW, HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND

WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

To the extent allowed by local law, Hewlett-Packard shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use of this

material.

A copy of the specific warranty terms applicable to your product and replacement parts can be obtained

from your local Sales and Service Office.

New editions of this guide are issued to reflect extensive changes made to the application. Revisions may

be issued between application versions to correct errors in the manual. There may not be a new edition

issued in conjunction with every application version release. The application version at the date of

printing is noted in the following table.

arranty

story

We want to hear from you. If you have any

comments, questions, or suggestions about our

documentation or support, send them to:

Email: [email protected]

Fax: +61 3 9210 5570

Phone: +61 3 9272 8633

Hewlett-Packard Australia Ltd

Communications Measurements Division Australia

PO Box 221

Blackburn, 3130

Victoria, Australia

Product support

Printed in Australia

opyr

Manual Name: Setting Up the 25.6 Mb/s Interface Pod

Manual Part Number: E5129-90001

Product Model Number: HP E5129A

Visit the Broadband Service Analyzer web site at http://www.hp.com/go/atmanalyzer

Edition Printing Date Application Version

1 October 1997 A.02.0

iii

Contents

Guide to the Broadband Service Analyzer Documentation..........................iv

About the 25.6 Mb/s Interface Pod ................................................................ 1

Online Help ..................................................................................................... 2

To Access User Online Help...................................................................... 2

Front Panel at a Glance ................................................................................. 3

Cable and Line Connector Details ................................................................. 4

Connector Cable Configurations ............................................................... 5

To Set Up the Interface Pod........................................................................... 6

To Insert the Interface Pod ....................................................................... 7

To Remove the Interface Pod................................................................... 8

To Connect to the System Under Test ..................................................... 8

Automatic Configuration Parameters ..................................................... 10

To Manually Configure the Interface Pod .............................................. 11

What to Do Next ........................................................................................... 12

Standards and Specifications........................................................................ 13

Communications Standards .................................................................... 13

Physical Specifications ............................................................................ 13

Environmental Specifications................................................................. 14

Guide to the HP E5200A Broadband Service Analyzer Documentation

Guide to the HP E5200A Broadband Service

Analyzer Documentation

The HP E5200A Broadband Service Analyzer comes with a comprehensive set

of paper and online documentation. Use the following table to determine

which documents you should use.

What is it? What does it do? Who is it for?

User’s Guide •contains instructions on how to set

up and install the analyzer

•provides an outline of the most

common functions

•provides an outline of the most

common system administration

functions

•lists electrical, mechanical, and

environmental speciﬁcations

all users

Application

Guide contains information on installing and

starting the application, along with an

overview of the application.

all users

Online Help four volumes–User, Macro, UPE

Compatibility, and Test help–contain

information about, and instructions

for using, the analyzer

all users

Quick Reference provides a quick overview of the

analyzer's main features and functions all users

Setting Up the

Interface Pod

guides

a series of guides that provide

descriptions of, and instructions for

installing, individual interface pods

all users will refer

to at least one of

these guides

Worldwide

Support card provides information about support,

service, and warranty all users

Release Notice provides information not available

when this guide was printed all users

About the 25.6 Mb/s Interface Pod

Overview The HP E5129A 25.6 Mb/s Interface Pod is a self-contained, plug-in

module. You use it in conjunction with the HP E5200A Broadband Service

Analyzer to test and analyze a system under test (SUT).

The interface pod generates and analyzes ATM cell streams in a 25.6 Mb/s

4B5B format, in accordance with ATM Forum ATM 25.6 Mb/s over Twisted

Pair Cable, af-phy-004.000.

Hot swap and

automatic

configuration

Use the “hot swap” feature to insert and remove the interface pod while

the analyzer’s power is switched on. The analyzer automatically detects

the insertion of the interface pod and conﬁgures itself accordingly.

Immediately after you connect the interface pod to the SUT, the analyzer

automatically conﬁgures the receive and transmit parameters according to

the signal it receives.

Operating modes The interface pod has three operating modes: full duplex, internal

transmit loopback, and receive loopback.

Components The interface pod is shipped with

•a Calibration Certiﬁcate

•a set of three connecting cables

•this Set Up guide

Application The HP E5129A 25.6 Mb/s Interface Pod requires an E5200A base unit

with Application Version number A.02.0 or greater.

Passive monitoring The 25.6 Mb/s Interface Pod has one connector only. To use the interface

pod to perform passive monitoring or bi-directional monitoring, you need

to obtain a special four-port junction box. See the application notes that

come with the interface pod for more details, or visit our web site:

www.hp.com/go/atmanalyzer

Online Help

The Online Help provides all the information you need to use the analyzer.

Refer to the HP Broadband Service Analyzer User’s Guide for information

on the Monitor/Simulate help. Refer to theApplication Guide for the B-ISDN

UNI Signaling Tests for information on the B-ISDN UNI Signaling Test help.

The Online Help contains a Reference section. Use the Reference section to

ﬁnd information about framing formats, alarms, errors, and measurements.

To Access User Online Help

There are four ways to access information in the User Online Help.

•Click the Help button that appears on most screens and windows to

display information about that screen or window.

•From the main screen Help menu, select User to display the User Contents

screen.

•Press F1. If the cursor is in an input ﬁeld, you see help for that ﬁeld;

otherwise you see the User Help Contents screen.

Front Panel at a Glance

Access (green LED) Lights each time the interface pod is accessed by the

network.

Signal (yellow LED) Lights when a valid signal is present at the input connector.

I/O Concentrator (UTP) Accepts an electrical signal from and provides a signal to the SUT.

Cable and Line Connector Details

The HP E5129A 25.6 Mb/s Interface Pod’s connector pin conﬁguration

adheres to the speciﬁcation deﬁned in the IBM Corporation’s ATM 25.6

Mb/s PHY Compatibility Speciﬁcation, Version 2.0, 15 October, 1993.

Note In order to comply with EMC regulations, you must use one of the three connection

cables that are supplied with the interface pod to connect to the system under test. See

Connector Cable Configurations on the next page for details.

Cable and Line Connector Details

Connector Cable Conﬁgurations

The interface pod comes with three cables:

•part number E1619-64300 connects a user device to the network (2 to

3 in the table below)

•part number E1619-64301 connects the interface pod to a user device

(1 to 2 in the table below)

•part number E1619-64302 connects the interface pod to the network

equipment (1 to 3 in the table below)

The following table sets out the pin conﬁgurations for the three connector

types:

1. Interface Pod

Connector

2. User Device

Connector

3. Network Equipment

Connector

Pin Signal Pin Signal Pin Signal

1 1 TxA 1 RxA

2 2 TxB 2 RxB

3 RxA 3 3

4 TxA 4 4

5 TxB 5 5

6 RxB 6 6

7 7 RxA 7 TxA

8 8 RxB 8 TxB

Pin 1

Pin 8

To Set Up the Interface Pod

Caution Handle the interface pod with care to avoid electrostatic discharge (ESD)

damage during unpacking, installation, and operation. The connectors on

the front and rear of the interface pod are susceptible to ESD.

1Insert the interface pod into the analyzer.

See “To Insert the Interface Pod” on page 7. The procedure is the same for

all interface pods.

2Connect the interface pod to the system under test.

See “To Connect to the System Under Test” on page 8. The analyzer

automatically recognizes and conﬁgures the interface pod.

3If you want to change any of the conﬁguration parameters, see “To

Manually Conﬁgure the Interface Pod” on page 11.

Indice

Manuali Scheda di rete popolari di altre marche

FirstComm

FirstComm OBiWiFi5G Manuale utente

Sun Microsystems

Sun Microsystems Interface Adapter Manuale utente

TRENDnet

TRENDnet TU2-ETG Manuale utente

YASKAWA

YASKAWA SI-EN3 Manuale utente

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuale utente

Belkin

Belkin F5D7050 Manuale utente

3Com

3Com EtherLink 3C509B Manuale utente

TRENDnet

TRENDnet TEG-PCITX Manuale utente

Cisco

Cisco MC16E Manuale utente

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuale utente

TwinMOS

TwinMOS Booming Manuale utente

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuale utente

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuale utente

National Instruments

National Instruments NI 9234 Manuale utente

Hama

Hama 49276 Manuale utente

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo

Compaq

Compaq Wireless LAN 100 Manuale utente

Bose

Bose PowerMatch Dante Manuale utente