Huawei SmartLogger2000-10-C-JP Manuale utente
HUAWEI TECHNOLOGIES CO., LTD.
SmartLogger2000-10-C-JP
Quick Guide (Japan)
Issue: 03
Part number: 31509082
Date: 2019-06-30
1
1Overview
1. The information in this document is subject to change without notice. Every effort has been made
in the preparation of this document to ensure accuracy of the contents. However, all statements,
information, and recommendations in this document do not constitute a warranty of any kind,
express or implied.
2. Before installing the device, carefully read the SmartLogger2000 User Manual to get familiar with
the product information and precautions. SmartLogger is short for SmartLogger2000-10-C-JP in
the following text.
3. Install and use the device according to this document and the user manual. Otherwise, the device
may be damaged. Use insulated tools when installing the device.
4. When the SmartLogger is applied in a non-Huawei smart array controller (smart array controller
for short), install it in the third-p arty cabinet. This section describes the installation and cable
connection operations using the SmartLogger in non-Huawei smart array controller scenario as
an example.
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
Model Description
1.1
Model
Description
SmartLogger2000
-10-C-
JP
10-C: with a built-
in 800 V AC PLC (MBUS) central coordinator (CCO)
JP: target market
The built-in Bluetooth module supports both Android APP and iOS APP.
NOTE
Port Description
1.2
No.
Port (Silk Screen)
Function Description
1
RF1, RF2
Reserved
Reserved.
2
12V OUT
12 V DC output
Provides 12 V DC power supply with a maximum
current of 100 mA.
3
12V IN
12 V DC input
Connects to the power adapter.
4
USB
USB port
Connects a USB flash drive.
5
SFP1, SFP2
Ethernet optical port
Connects to an ATB or another cascaded
SmartLogger.
6
ETH1, ETH2
Ethernet electrical
port
Connects to an Ethernet LAN switch, router or
PC device.
7
DO
Digital output (DO)
Relay output supports 12 V voltage and 0.5 A current.
8
COM1
–COM6
RS485
communications
Six RS485 ports that can be connected to devices
such as
the inverter, cubicle, power meter, or EMI.
No.
Port (Silk Screen)
Function Description
9
Default
Default key
Resets and restarts the Bluetooth module or resets
the SmartLogger IP address to the default IP address
(valid within 5 minutes). The default IP address is
192.168.0.10.
10
AC1, AC2
AC power cable
ports
Connects to
three-phase (U, V, and W) inputs
, and is
used for PLC (MBUS) with the SUN2000 over AC
power cables.
If PLC (MBUS) function is not used,
you do not have to connect cables to these ports.
11
Shell
ground point
N/A
12
AI1
–AI7
Analog input
AI1 supports 0
–10 V input voltage (passivea); AI2–
AI7 support 0
–20 mA and 4–20 mA input current
(passive).
13
PT1, PT2
Analog input
PT1 supports the connection to a three-wire or two
-
wire PT100/PT1000 temperature sensor.
PT2 supports the connection to only a two-wire
PT100/PT1000 temperature sensor.
14
AO1
–AO4
Analog output (AO)
4
–20 mA and 0–20 mA output current
15
DI1
–DI8
Digital input (DI)
Connects to a dry contact input. GND1 and GND2
are ground ports for DI signals.
Note a: Passive means that the AI port can connect to a sensor that needs to be energized separately.
2
2Typical Cable Connection Scenarios
Non-Smart Array Controller Scenario
2.1
1. The SmartLogger can connect to an inverter over an RS485 communications cable.
2. The power cable delivered with the SmartLogger is 1 meter long, the power adapter cable is 1.5
meters long, the network cable is 2.2 meters long, and the AC power cable is 1.5 meters long.
Reserve the installation positions for components based on the cable lengths.
3. The tables under figures list only the components to be configured by the customer in the
corresponding scenario.
Optical Fiber
3
Component Recommended Model or Specifications Component
Source Quantity
SmartLogger SmartLogger2000 Can be
purchased
from Huawei 1
Fitting
bag for
fiber ring
switching
Low-speed
optical
module FTLF1323P1BTR-HW Can be
purchased
from Huawei
2
Optical
jumper PLCLC5S-ST3P302-HW, LC-LC-S2-L2,
3ECA1031LCLC002-01-F, or LP-LP-2S-P-SM-002 8
ATB CT-GZF2PJ-8, CT-GPH-A-8, or an ATB of a local
model Prepared by
the customer 1
Socket Connects to the power adapter. Prepared by
the customer 1
Smart Array Controller Scenario
2.2
This document describes the application scenario where the SmartLogger is inside the smart
array controller SmartACU2000B-D-2PID/2PLC.
The tables under figures list only the components to be configured by the customer in the
corresponding scenario.
NOTE
1. Prepare the single-phase AC power cable for the smart array controller by yourself. Recommended:
a two-core outdoor armor copper cable with an operating voltage to the ground greater than or equal
to 300 V and a cross-sectional area of 5.5 mm2for each core wire
2. The cable from the molded case circuit breaker (MCCB) to the station-service power source is
prepared by the customer. Recommended: a two-core outdoor armor copper cable with an operating
voltage to the ground greater than or equal to 300 V and a cross-sectional area of 5.5 mm2for each
core wire
3. Prepare the three-phase AC power cable for the smart array controller by yourself. Recommended: a
four-core (U, V, W, and functional earthing) outdoor armor copper cable with a cross-sectional area
of 8 mm2for each core wire. When the rated AC voltage on the low-voltage side of the cubicle is less
than or equal to 500 V, the operating voltage between the three-phase AC power cable and the
ground should be greater than or equal to 600 V.
4. The cable from the busbar to the 3P3E switch is prepared by the customer. Recommended: a four-
core (U, V, W, and functional earthing) outdoor armor copper cable with a cross-sectional area of 8
mm2for each core wire. When the rated AC voltage on the low-voltage side of the cubicle is less
than or equal to 500 V, the operating voltage to the ground should be greater than or equal to 600 V.
4
Optical Fiber
PLC
(MBUS)
CCO
5
Location Component Recommended Model or
Specifications Component
Source Quantity
Smart array
controller
LAN switch (optional) UT-H605 or ES1000 Can be
purchased
from Huawei 1
Fitting bag
for optical
ring
switching
Low-
speed
optical
module
FTLF1323P1BTR-HW Can be
purchased
from Huawei
2
Optical
jumper
PLCLC5S-ST3P302-HW, LC-
LC-S2-L2,
3ECA1031LCLC002-01-F, or
LP-LP-2S-P-SM-002
8
Cubicle
MCCB Rated current: 30 A, number
of poles: 2 Prepared by
the customer 1
3P3E switch
When the rated AC voltage
on the low-voltage side of
the cubicle is less than or
equal to 500 V, the rated
insulation voltage should
be 600 V.
The number of poles is 3.
When the rated AC voltage
on the low-voltage side of
the box-type transformer is
less than or equal to 500 V,
the rated current should be
30 A.
Prepared by
the customer
Scenario with a
double-column
transformer: 1
Scenario with a
dual-split
transformer: 2
Installation clearances
Guide rail-mounting
Chassis dimensions
(including the guide rail mounting brackets)
6
Installation Space (Unit: mm)
3.1
3Installing the SmartLogger
Chassis dimensions (including mounting ears) Installation clearances
Wall-mounting
Installation Mode
3.2
Wall-mounting
Install the SmartLogger on a wall that is flat and has the bearing capacity to securely hold the
SmartLogger.
Screw assembly for wall-mounting:
(1) ST3.5 tapping screw
(2) Washer
(3) Expansion sleeve
2. Drill holes by using a hammer drill and install expansion sleeves, washers, and tapping screws.
7
3. Put the tapping screws through the SmartLogger mounting ears and washers into the mounting
holes in the wall.
Unit: mm
1. Determine mounting holes based on the hole positions in the mounting ears, and mark
the mounting holes using a marker.
If you need to use a ladder to
install the device on a high
position, take measures to protect
yourself from falling down.
Unit: mm
4. Tighten the tapping screws using a torque screwdriver.
1. Remove the mounting ears from the
SmartLogger using a Phillips screwdriver. 2. Secure the guide rail clamps using the screws
that are removed from the mounting ears.
8
Guide rail-mounting
Huawei does not provide the SmartLogger guide rail. If the customer chooses this installation mode,
the customer must prepare a 35 mm standard guide rail.
Unit: mm
1. Secure the guide rail before mounting the
SmartLogger.
2. Verify that the length of the guide rail is
sufficient for securing the SmartLogger. The
recommended length is 450 mm or greater.
NOTE
3. Mount the SmartLogger onto the guide rail. 4. Install guide rail fasteners.
9
4Installing Ground Cable
Installing the SmartLogger Ground Cable
4.1
1. It is recommended that 4–6 mm2or 12–10 AWG outdoor copper-core cables be used as ground
cables. Ground cables must be securely connected.
2. To enhance the corrosion resistance of the ground terminal, apply silica gel or paint on it after
connecting the PGND cable.
OT-M6
NOTE
5Connecting Cables to COM Ports
The SmartLogger can connect to a inverter, an EMI, a power meter, a cubicle, and a PID module
through its COM ports.
NOTE
Port Definitions
5.1
For the definitions of the communications ports on the devices such as the EMI, power meter, and
cubicle, see the documents delivered with the devices. When connecting cables, ensure that
RS485+ connects to the COM+ port on the SmartLogger and that RS485–connects to the COM–
port on the SmartLogger.
For ease of operation, this document describes only the ports that need to be wired.
NOTE
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Huawei Unità di controllo
Huawei
Huawei MU709s-2 Istruzioni per l'installazione
Huawei
Huawei VP9660 Manuale utente
Huawei
Huawei UPS5000-E-200K-SM Manuale utente
Huawei
Huawei ME309-562 Istruzioni per l'installazione
Huawei
Huawei RRU3269 Manuale utente
Huawei
Huawei UPS5000-E Series Manuale utente
Huawei
Huawei APM30H Manuale utente
Huawei
Huawei ME919Bs-567bN Manuale utente
Huawei
Huawei ICD OPS D Series Manuale utente
Huawei
Huawei UPS5000-H-1200K-NT Manuale utente
Huawei
Huawei MU509-65 Istruzioni per l'installazione
Huawei
Huawei ME909s-120 Istruzioni per l'installazione
Huawei
Huawei G530 V2 Guida di riferimento rapido
Huawei
Huawei MU709s-2 Istruzioni per l'installazione
Huawei
Huawei EM660 Manuale utente
Huawei
Huawei Atool Manuale utente
Huawei
Huawei MU203 Manuale utente
Huawei
Huawei MU709 Series Istruzioni per l'installazione
Huawei
Huawei RMS-SNMP01A Manuale utente
Huawei
Huawei MU739 Istruzioni per l'installazione
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
