ICP DAS USA I-7041 Manuale utente

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

I-7041

14 Channel Isolated Digital Input Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/i_7041

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The I-7041 provides 14 channels for digital input, each of which features

photo couple isolation. In addition, sink- or source-type digital input can be

selected via wire connections, and all channels are able to be used as 16-

bit counters. 4 kV ESD protection and 3750 VDC intra-module isolation are

standard. ICPDAS recommends selecting the "P" version of the digital input

module for industrial use.

2. Terminal Assignment

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default settings for the I-7043 DIO modules are as follows:

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

。J3 set to INIT mode enabled for I-7043/43D a

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA IR-712A Manuale utente

ICP DAS USA

ICP DAS USA EIP-2000 Series Guida all'installazione

ICP DAS USA

ICP DAS USA M-7019Z Manuale utente

ICP DAS USA

ICP DAS USA DS-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA tGW-700 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7026 Manuale utente

ICP DAS USA

ICP DAS USA tSH-700 Series Manuale utente

ICP DAS USA

ICP DAS USA CAN-8123 Manuale utente

ICP DAS USA

ICP DAS USA ET-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7033D Manuale utente

ICP DAS USA

ICP DAS USA tET Series Manuale utente

ICP DAS USA

ICP DAS USA WF-2017 Manuale utente

ICP DAS USA

ICP DAS USA PETL-7060 Manuale utente

ICP DAS USA

ICP DAS USA GPS-721-MRTU Manuale utente

ICP DAS USA

ICP DAS USA ET-2260 Manuale utente

ICP DAS USA

ICP DAS USA I-8026W Manuale utente

ICP DAS USA

ICP DAS USA USB-87P1 Manuale utente

ICP DAS USA

ICP DAS USA M-7028 Manuale utente

ICP DAS USA

ICP DAS USA tET-P2A2 Manuale utente

ICP DAS USA

ICP DAS USA tM Series Manuale utente

ICP DAS USA

ICP DAS USA DS-700 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7053D Manuale utente

ICP DAS USA

ICP DAS USA ET-2260 Manuale utente

ICP DAS USA

ICP DAS USA ET-7H16M Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente