ICP DAS USA M-7033D Manuale utente

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7033D

3 Channel RTD Input Data Acquisition

Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7033d.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7033D is a 3-channel RTD Input module that is used for measuring temperatures

via an RTD sensor and supports Pt100, Ni120, and Pt1000 type sensors. The module

allows 2/3/4-wire RTD connections and features open wire detection. In addition, the M-

7033 also includes 3000 VDC intra-module isolation, and supports lead resistance

elimination for 3/4-wire connections.

2. Terminal Assignment

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

Default settings for the M-7024 module are as follows:

▫Protocol: Modbus RTU

▫Module address: 01

▫Analog output type: 0 ~ +10 V

▫Baud Rate: 9600 bps

▫Engineering unit format

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For M-7000 modules using the Modbus RTU protocol, configure the module using the

following functions.

Sub-function 04h of Function 46h, see user manual Section 3.3.2

Sub-function 06h of Function 46h, see user manual Section 3.3.4

Sub-function 08h of Function 46h, see user manual Section 3.3.6

For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the

data from the input channels. See user manual Section 3.2 for details.

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA ZT-2026 Manuale utente

ICP DAS USA

ICP DAS USA I-8088W Manuale utente

ICP DAS USA

ICP DAS USA PM-4324 Series Manuale utente

ICP DAS USA

ICP DAS USA DS-700 Series Manuale utente

ICP DAS USA

ICP DAS USA ET-7065 Manuale utente

ICP DAS USA

ICP DAS USA I-8026W Manuale utente

ICP DAS USA

ICP DAS USA GTP-230 Manuale utente

ICP DAS USA

ICP DAS USA SG-3016 Manuale utente

ICP DAS USA

ICP DAS USA SG-785 Manuale utente

ICP DAS USA

ICP DAS USA tZT-P4C4 Manuale utente

ICP DAS USA

ICP DAS USA GTM-204M-4G Manuale utente

ICP DAS USA

ICP DAS USA LP-8 4 Series Istruzioni generali

ICP DAS USA

ICP DAS USA tET Series Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7017R Manuale utente

ICP DAS USA

ICP DAS USA tM-AD5 Manuale utente

ICP DAS USA

ICP DAS USA IR-310-RM Manuale utente

ICP DAS USA

ICP DAS USA PETL-7060 Manuale utente

ICP DAS USA

ICP DAS USA PROFIBUS PROFI-2510 Manuale utente

ICP DAS USA

ICP DAS USA ECAT-2016N Manuale utente

ICP DAS USA

ICP DAS USA I-7055D Manuale utente

ICP DAS USA

ICP DAS USA ET-7000 series Manuale utente

ICP DAS USA

ICP DAS USA M-7067D Manuale utente

ICP DAS USA

ICP DAS USA M-7088 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente