ICP DAS USA M-7060 Manuale utente



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1



M-7060

4-channel Digital Input and 4-channel Relay

Output Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7060_m_7060d

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The 7060 series provides 4 digital input channels, 2 Form A and 2 Form C signal relay output

channels, while the M-7060P provides 4 digital input channels, 2 Form A and 2 Form C power

relay output channels. All digital input channels can be used as 16-bit counters. In addition, the

digital input channels can be selected either as sink- or source-type via wire connections. The

“D” versions of the 7060 series provide eight LED indicators that can be used to monitor the

status of the digital input and relay output. The “M” versions of the 7060 series support both the

Modbus RTU and DCON protocols, which can be configured via software. There are also

options for configuring power-on and safe values. 4 kV ESD protection and 3750 VDC intra-

module isolation are also provided to enhance noise protection capabilities in industrial

environments. The 7060 series is the ideal solution for small signal switching applications, while

the M-7060P is the perfect solution for high power applications.

2.TerminalAssignment



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2



3.Block/WiringDiagram



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3



4. Default Settings

。 Module Address: 01

。 DIO Type: Type 40

。 Baud Rate: 9600 bps

。 Checksum disabled

5. Configuration

To install the module, follow the steps below:

1. Connect the digital input and output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5



4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format

to search module. The default settings for the module can be found in Section 3.

Click OK after selecting the COM port setting.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6



5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7



7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.



Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA I-8213W-4G Manuale utente

ICP DAS USA

ICP DAS USA ET-7000 series Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA I-7188XA Manuale utente

ICP DAS USA

ICP DAS USA I-7088 Manuale utente

ICP DAS USA

ICP DAS USA Zigbee ZT-2060 Manuale utente

ICP DAS USA

ICP DAS USA GTP-230 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Manuale utente

ICP DAS USA

ICP DAS USA ET-6000 Series Manuale utente

ICP DAS USA

ICP DAS USA HRT-370 Manuale utente

ICP DAS USA

ICP DAS USA ZT-2026 Manuale utente

ICP DAS USA

ICP DAS USA I-7045D Manuale utente

ICP DAS USA

ICP DAS USA I-8094 Manuale elenco delle parti

ICP DAS USA

ICP DAS USA tM Series Manuale utente

ICP DAS USA

ICP DAS USA I-87004W Manuale utente

ICP DAS USA

ICP DAS USA PDS-5000 Series Manuale utente

ICP DAS USA

ICP DAS USA MN-3253 Series Manuale utente

ICP DAS USA

ICP DAS USA WISE-5801-MTCP Manuale utente

ICP DAS USA

ICP DAS USA tSH-734 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD5 Manuale utente

ICP DAS USA

ICP DAS USA ECAT-2061 Manuale utente

ICP DAS USA

ICP DAS USA M-7051D Manuale utente

ICP DAS USA

ICP DAS USA ZT-2017 Manuale utente

ICP DAS USA

ICP DAS USA DL-10 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente