ICP DAS USA I-7060D Manuale utente

I-7060D 4 Ch DI and 4 Ch Relay Output DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

I-7060D

4 Channel Isolated Digital Input (Counter)

and 4 Channel Relay Output Data Acquisition

Module (with Display)

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/i_7060d.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

I-7060D is intelligently designed to provide signal conditioning system

monitoring and safe value settings. I-7060 is a cost-effective solution for a

wide range of valuable industrial control signals and systems. The DCON

utility can help users to configure and test I-7060 Relay output and digital

Input module. Plenty of library functions and demo programs are provided

to let users develop programs easily under Windows, Linux and DOS

operating systems. The communication interface is modbus protocol via

RS-485. Users may mount the modules on a DIN rail, panel or wall.

Modules have a screw-terminal block to connect to the signals.

2. Terminal Assignment

I-7060D 4 Ch DI and 4 Ch Relay Output DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

I-7060D 4 Ch DI and 4 Ch Relay Output DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default settings for the I-7060D DIO modules are as follows:

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

。J3 set to INIT mode enabled for I-7043/43D.

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

I-7060D 4 Ch DI and 4 Ch Relay Output DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7060D 4 Ch DI and 4 Ch Relay Output DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7060D 4 Ch DI and 4 Ch Relay Output DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

I-7060D 4 Ch DI and 4 Ch Relay Output DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA DS-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA ET-7H16M Series Manuale utente

ICP DAS USA

ICP DAS USA WF-2017 Manuale utente

ICP DAS USA

ICP DAS USA tM Series Manuale utente

ICP DAS USA

ICP DAS USA I-7063 Manuale utente

ICP DAS USA

ICP DAS USA tSH-734 Manuale utente

ICP DAS USA

ICP DAS USA PETL-7060 Manuale utente

ICP DAS USA

ICP DAS USA ZT-257 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7017R Manuale utente

ICP DAS USA

ICP DAS USA I-7045 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD5 Manuale utente

ICP DAS USA

ICP DAS USA I-7088 Manuale utente

ICP DAS USA

ICP DAS USA I-7083 Manuale utente

ICP DAS USA

ICP DAS USA tGW-700 Series Manuale utente

ICP DAS USA

ICP DAS USA tM-TH8 Manuale utente

ICP DAS USA

ICP DAS USA M-7019Z Manuale utente

ICP DAS USA

ICP DAS USA ECAT-2050 Manuale utente

ICP DAS USA

ICP DAS USA PET-AR400 Manuale utente

ICP DAS USA

ICP DAS USA ECAT-2016N Manuale utente

ICP DAS USA

ICP DAS USA tSG-3781B Manuale utente

ICP DAS USA

ICP DAS USA M-7024 Manuale utente

ICP DAS USA

ICP DAS USA GTM-204M-4G Manuale utente

ICP DAS USA

ICP DAS USA ET-87P2 Manuale utente

ICP DAS USA

ICP DAS USA ET-7065 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente