ICP DAS USA TM-P3R3 Manuale utente

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

tM-P3R3

3-channel Isolated Digital Input and 3-

channel Relay Output Module

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/tm_p3r3.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The tM-P3R3 provides 3 channels for digital input and 3 channels for relay output, each

of which features photocouple isolation. All output channels are form A type relays,

while input is based on sink- or souce-type using a wire connecion. All input channels

can be used an 16-bit counters. There are options for configuring power-on and safe

digital output values. 4 kV ESD protection and 3750 VDC intra-module isolation are also

provided.

2. Terminal Assignment

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

•Use 26-12 AWG wire for signal

connections.

•Strip the wire to a length of

7±0.5mm.

•Use a crimp terminal for wiring.

•Avoid high-voltage cables and

power equipment as much as

possible.

•For RS-485 communication, use

insulated and twisted pair 24 AWG

wire, e.g. Belden 9841.

4. Default Settings

Default settings for the tM-P3R3 module are as follows:

。Protocol: Modbus RTU

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. The Modbus RTU communication protocol is the default protocol of the tM series.

The communication Baud Rates for the Modbus RTU protocol can be in the range of

1200 bps to 115200 bps

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA ET-7218Z Manuale utente

ICP DAS USA

ICP DAS USA tSH-700 Series Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7016 Manuale utente

ICP DAS USA

ICP DAS USA GPS-721-MRTU Manuale utente

ICP DAS USA

ICP DAS USA LP-8 4 Series Istruzioni generali

ICP DAS USA

ICP DAS USA ET-7200 Series Manuale utente

ICP DAS USA

ICP DAS USA ET-7000 series Manuale utente

ICP DAS USA

ICP DAS USA tDS-700-T Series Manuale utente

ICP DAS USA

ICP DAS USA M-7026 Manuale utente

ICP DAS USA

ICP DAS USA M-7069D Manuale utente

ICP DAS USA

ICP DAS USA WF-2051 Manuale utente

ICP DAS USA

ICP DAS USA ET-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA EIP-2000 Series Manuale utente

ICP DAS USA

ICP DAS USA I-7041 Manuale utente

ICP DAS USA

ICP DAS USA I-7080 Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA ET-2260 Manuale utente

ICP DAS USA

ICP DAS USA M-7017R Manuale utente

ICP DAS USA

ICP DAS USA I-7188XA Manuale utente

ICP DAS USA

ICP DAS USA I-7045 Manuale utente

ICP DAS USA

ICP DAS USA PM-3033 Series Manuale utente

ICP DAS USA

ICP DAS USA tM-AD5 Manuale utente

ICP DAS USA

ICP DAS USA M-7002 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

ICP DAS USA tM-P3R3 Manuale utente

Manuali Unità di controllo popolari di altre marche