ICP DAS USA Zigbee ZT-2060 Manuale utente

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 1

ZT-2060

Zigbee Wireless 6-channel Digital Input, 4-channel

Relay Output Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/zt_2060.html

Introduction

The ZT-2060 offers 4 Form A power relay output channels and 6 digital input

channels, each of which features photocouple isolation. In addition, you can

choose sink-type or source-type input via wire connections. All channels are able

to be used as 16-bit counters. The ZT-2060 has 10 LED indicators to display the

channel status, and has 4 kV ESD protection and 3000 VDC intramodule isolation.

Users can easily configure the module address, protocol, checksum, ZB-PID and

ZB-channel settings using a combination of rotary and DIP switches.

What’s in the Shipping Package?

The shipping package contains the following items:

ZT‐2060 DIO Device ANT‐124‐05 Quick Start

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2

Preparing the Device

1. Refer the chapter 3. to configure the DIP switch of ZT-2060 I/O device.

2. Install the ZT Configuration Utility to configure the ZT-2060 coordinator.

CD:

\Napdos\ZigBee\ZT_Series\Utility http://ftp.icpdas.com/pub/cd/usbcd/nap

dos/zigbee/zt_series/utility

3. Power Supply: +10 ~ +30 VDC

Setting up the ZT‐2060 DIO Device

3.1 Introduction to the Configuration Parameters

A. “Pan ID” parameter is the group identity for a ZigBee network, and

must the same for all devices in the same ZigBee network.

“Address/Node ID” parameter is the individed identity of a specific

the ZigBee module, and must be unique for each device connected the

same ZigBee network.

B. “RF Channel” parameter indicates the radio frequency channel, and must

be set to the same value as other modules on the same ZigBee network.

Channel

0x00

0x01

……

0x0F

Frequency(MHz)

2405

2410

……

2480

※RF channels 0x04, 0x09, 0x0E or 0x0F are recommended because they do

not overlap with the Wi-Fi frequencies based.

802.11b/g

Channel 1

Channel 6

Channel 11

2400 00

2485

MHz

802.11b/g Channel (North America)

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 3

802.15.4 Channel

C. Protocol/Application Mode：

When implementing custom programs based on different protocols, the

following application modes are recommended in order to ensure

communicatible

User Program Protocol

DCON

Modbus RTU

Modbus TCP

ZT-2060 I/O

ZT-2550

ZT-2570

DCON

Transparent

Modbus RTU

Transparent

Modbus Gateway

Modbus RTU

------

Modbus Gateway

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4

Rotation Switch and DIP Switch

The configuration of ZT-2060 series can be adjusted by using the

external rotary switch and the DIP switches. The ZT-2060 device should

only be rebooted once the configuration is complete.

 DIP Switch to the ZT‐2042/ZT‐2043/ZT‐2060/ZT‐2055

Protocol Pan ID

Checksum

RF Channel

Reserved

Address LSB

Address MSB

(Node ID)

 DIP Switch to the ZT‐2060/ZT‐2060

Protocol Pan ID

Address LSB

Address MSB

Checksum

RF Channel

(Node ID)

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 5

 Rotation Switch

……

Note

Address

……

MSB = 0

Node ID

0x0001

0x0002

0x003

……

0x000F

……

Address

……

MSB = 1

Node ID

0x0010

0x0011

0x0012

0x013

……

0x001F

※Once the address of hardware switch is set to 0x00, it mens the address is using

software configurations. Refer the more detailed information at Sec. 6.6 of user

manual.

 DIP Switch

Number

Item

Status

Explain

Address MSB

OFF

Valid Address (Node ID) from 0x00 to 0x0F

Valid Address (Node ID) from 0x10 to 0x1F

Protocol

OFF

DCON Protocol

Modbus RTUProtocol

Checksum

OFF

Disabled

Enabled

ZigBee Pan ID

OFF

Pan ID = 0x0000

Pan ID = 0x0001

OFF

------

0x08

OFF

------

ZigBee

0x04

RF Channel

OFF

------

0x02

OFF

------

0x01

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 6

Start‐up ZT‐2000 I/O Device

As the ZigBee network is controlled by the ZigBee coordinator, the ZT-

2550/ZT-2570 (ZigBee coordinator) must be configured first. Please refert to

documents shown below for full details of how to configure these devices.

Once configuration of the ZigBee coordinator has been completed. Set

the ”Pan ID” and the “RF Channel” values for the ZT-2000 I/O device to the

same values as the network, and then reboot the device. The module will

automatically start to function on the ZigBee network using the default protocol.

※Configuration Utility (Used to configure ZT-2000 I/O device Coordinator)

http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/utility/

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 7

Examples

 Configurations of ZT‐2550/ZT‐2570

 Configurations of ZT-2000 I/O Device

12345678910 11 12

Number

Item

Status

Explain

Address MSB

OFF

Address/Node ID is 01(Rotation Switch=1)

Protocol

Use Modbus RTU Protocol

Checksum

OFF

Disabled

ZigBee Pan ID

OFF

Pan ID=0x0000

0x08

ZigBee

0x04

ZigBee RF Channel = 0x0E

RF Channel

0x02

OFF

------

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 8

Communication Test

Once the ZT-2000 I/O device has joined the ZigBee network, the signal

quality can be comfirmed by monitoring the status of the ZigBee Net LED

indicators. If the LED indicator shows a steady light, communication with

the ZT-2000 I/O device has been successfully established for data

acquisition and control.

ICP DAS also provides the “DCON Utility”, which can be used to

simulate DCON/Modbus communication. This software can also be used

to verify the device settings and ZigBee I/O functions.

※The DCON Utility can be dowmload from:

http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/

Simulate I/O channel operating via using DCON Utility

1. Launch DCON Utility and select the correct COM Port settings to

connect the ZigBee Coordinator (ZT-2550/ZT-2570).

2. Clicking “Search” button will start searching which ZT-2000 I/O device

is in the same ZigBee network.

3. If there is any ZT-2000 I/O devices displayed, double clicking the

“module name” will start the I/O channels operated platform.

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 9

ZT-2060 Zigbee 6-ch DI, 4-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 10

Troubleshooting

(1) Technical Support.

If you have any difficulties using your ZT-2000 series I/O device,

please send a description of the problem to [email protected]om

Include the following items in your email:

A description or diagram of the current DIP switch positions.

A copy of the configuration file for the ZT-2000 coordinator. This file

can be obtained using the procedure outlined below and should be

attached to your email.

a. Set the DIP switch of the ZT-255x device to the [ZBSET] position then

reboot the device. Launch the ZT Configuration Utility and select [Save

Log] icon to save the configuration of the ZT-255x as a file.

b. After clicking the [Save Log] icon, enter the “File Name” and the “File

Path” in the Windows “Save” dialog box. Once the configuration has

been successfully saved, the following message will be displayed.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA iDaSer-9000 Manuale utente

ICP DAS USA

ICP DAS USA I-7083 Manuale utente

ICP DAS USA

ICP DAS USA PETL-7060 Manuale utente

ICP DAS USA

ICP DAS USA WP-5231 Manuale utente

ICP DAS USA

ICP DAS USA I-8124W Manuale utente

ICP DAS USA

ICP DAS USA M-7026 Manuale utente

ICP DAS USA

ICP DAS USA LP-8 21 Series Istruzioni generali

ICP DAS USA

ICP DAS USA ET-87P2 Manuale utente

ICP DAS USA

ICP DAS USA tSH-725 Manuale utente

ICP DAS USA

ICP DAS USA ET-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA I-7041 Manuale utente

ICP DAS USA

ICP DAS USA PET-7261 Manuale utente

ICP DAS USA

ICP DAS USA I-7088 Manuale utente

ICP DAS USA

ICP DAS USA GT-540P-3GWA-OEM1 Manuale utente

ICP DAS USA

ICP DAS USA DS-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA tM-AD5 Manuale utente

ICP DAS USA

ICP DAS USA SG-3016 Manuale utente

ICP DAS USA

ICP DAS USA tSH-700 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7060 Manuale utente

ICP DAS USA

ICP DAS USA SG-3071 Manuale utente

ICP DAS USA

ICP DAS USA ZT-2026 Manuale utente

ICP DAS USA

ICP DAS USA WF-2051 Manuale utente

ICP DAS USA

ICP DAS USA PDS-220F Series Manuale per l'uso e la cura

ICP DAS USA

ICP DAS USA tET-P6 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente