4
Length of the Cable: 47.2"/1.2m
Temperature Control Range:
32℉~194℉ ( 0℃~90℃)
Temperature Control Accuracy: 1℉/0.1℃
Temperature Display Accuracy: 1℉/0.1℃
Time Setting Range: Max 99 hours and 59
minutes
Time Setting Minimum Interval: 1 minute
Reminder: There will be hint tone when the
water temperature reaches the set
temperature or the countdown ends.
Water Shortage Protection: If the water level
is below the minimum scale line, the device
will automatically stop working and alarm.
Waterproof Level: Non waterproof
Heating Power: 1000W
Input voltage: (US) AC 120v 60Hz, (EU, UK,
AU) AC 220~240v 50Hz
1.3 Item List
1. Sous Vide*1
2. Manual*1
3. Warranty Card*1 3.1 Temperature setting and timer
setting
1. Press the “ ” button to enter main
interface setting mode.
2. When the set temperature icon is flashing,
you can adjust the temperature by pressing
the “ ” button or the “ ” button.
3. Press the “ ” button again to set the
hours of the countdown, another press on
the “ ” button to set the minutes of the
countdown.
Note: Long press on the “ ” button or
the “ ” button will increase or decrease
the temperature value quickly.
3.2 Temperature Unit Switch &
Calibration
3.2.1 Temperature Unit Switch
1. Hold the “ ” button for seconds to enter
the temperature unit setting page.
2. Press the “ ” button or the “ ” button
to switch between ℉ and ℃.
3. Hold the “ ” button to confirm the
selection and back to main interface.
3.2.2 Calibration
1. Hold the “ ” button for seconds to enter
the temperature unit setting page.
2. Short press the “ ” button to enter
calibration setting page.
3. Press the “ ” button or the “ ” button to
calibrate.
4. Hold the “ ” button to confirm the
calibration value and back to main interface.
3.3 Start/Stop Cooking
Press the “ ” button to start or stop cooking.
You can check the working state at the upper
left corner of the screen.
4.2 Connect the Sous Vide to your
phone
4.2.1 Fast Flash Mode
1. Please register an account before using
the InkBird Pro app. Select your Country/
Region, enter your e-mail, then a verification
code will be sent to your mailbox, enter it to
confirm your identity and the registration is
done.
2. Open the app and click “ + ” to start the
connection.
3. Plug in the Inkbird Sous Vide, make sure
the Wi-Fi icon is blinking rapidly and choose
Fast Flash mode on your phone, select a
preferred Wi-Fi network and enter the
password to connect.
4. Connection succeed.
Note: If you have registered an account
before, just log in directly.
4.2.2 AP Mode
The Wi-Fi icon flashes rapidly by default.
Press and hold the “ ” button for 5
seconds to switch to AP mode, the Wi-Fi icon
flashes slowly in the mode.
1. Open the app and click “ + ” to start the
connection.
2. Plug in the Inkbird Sous Vide, and choose
it from the device list, confirm the Wi-Fi icon
of the Sous Vide is blinking slowly and
choose Slow Flash mode.
3. Choose a preferred Wi-Fi network and
enter the password, then click “Confirm” to
go to the next step.
4. Enter into your phone’s WLAN interface
and connect to the “SmartLife XXXX” Wi-Fi
network without typing in the password.
Return to the app and confirm that the
network has been successfully connected.
5. Connection succeed.
4.3 Wi-Fi Reset
Press and hold the “ ” button for 5 seconds
to reset the Wi-Fi, then repeat the steps above
to connect the Sous Vide to your phone. The
device only supports 2.4GHz Wi-Fi router.
Settings03
