Interlogix PIR Manuale utente

P/N 1079525 (EN) • REV A • ISS 05JUN13 1

PIR Camera Reference

Manual

Content

Contact information 1

Introduction 1

ATS1238 expander 4

Wireless PIR camera 5

Troubleshooting 6

Programming menus specific for PIR camera 7

Basic user commands 13

User menus 14

Camera diagnostics 16

Walk tests 16

Contact information

For contact information, see www.utcfireandsecurity.com or www.interlogix.com.

For customer support, see www.utcfssecurityproducts.eu.

reserved.

Introduction

This manual explains how to install, commission, program, and use wireless PIR

cameras together with Advisor Advanced systems.

A wireless PIR camera is a wireless PIR detector with a camera built-in. The

camera can be programmed to take pictures in case of activation of associated

zones, conditional filters, as well as by manual activation or remote requests.

After an alarm the associated pictures are sent to a central station via IP/GPRS.

Pictures can also be viewed from configuration software.

2 PIR Camera Reference Manual

System structure

An Advisor Advanced system can have one ATS1238 wireless PIR camera

expander mounted inside of the panel housing, and connected to the MI bus.

See “ATS1238 expander” on page 4 for details.

The system with a wireless PIR camera expander can have up to 8 wireless PIR

cameras programmed.

Figure 1: System structure

Camera activation

The system with a wireless PIR camera expander can have up to 8 wireless PIR

cameras programmed. Each camera can be activated in case of the following

events:

•Activation of one of 4 assigned zones. Zones are assigned in menu “4.3.n.2

Pics by zone” on page 11.

In this case camera event type depends on the zone type. See “Camera

event types” on page 3.

•Activation of a condition filter. The event type is defined for the programmed

filter. See “4.3 Cameras” on page 10.

•Activation of a standard reporting event. See “4.3.n.4 Pics by rep ev” on page

12.

•User command.

•Remote request from configuration software.

The number and the quality of pictures taken depend on the camera event type.

See “Programming menus” on page 7 for details.

USB

CON23

CON19

CON12 LK2

CON13

USB

LK3

S3 S4 S5

S1 C

S2 C T C

- - 1 C 2 3 C 4 5 C 6 7 C 8

~~+-

AC BATT LC-OUTPUTS HC-OUTPUTS SIRTMP AUX POWER INPUTS

Ax/R1

B/TA/R

EARTH

CTD-

D+

+12V COMMS TAMPER PSTN

ATS1238

ATS1000A

1 2 3 4

MI-BUS

HDR-ANT2

LDRM-ANT1

HDR-ANT1

LDRM-ANT2

( )6

PIR Camera Reference Manual 3

Camera event types

There are the following camera event types available.

•Burglar alarm. Generated by alarm, entry/exit, access, 24 H, firedoor and

keybox type zones.

•Fire alarm. Generated by fire zones.

•Panic alarm. Generated by panic zones.

•Medical alarm. Generated by medical zones.

•Tamper alarm. Generated by tamper zones.

•Fault. Generated by technical, transmission fault, aux mains fault and aux

battery fault type zones.

•Custom type 1. Generated by conditional filters of this type.

The types are assigned to conditional filters.

•Custom type 2. Generated by conditional filters of this type.

Event type details are listed in Table 1 below.

Table 1: Camera events and reporting codes

Event type

Activated by zone type [1]

SIA code [2]

Burglar alarm

1. Alarm, 2. Entry/Exit 1, 3. Access, 6. 24H, 13. Fire door,

16. Key box, 18. Entry/Exit 2

Fire alarm

4. Fire

Panic alarm

5. Panic

Medical alarm

10. Medical

Tamper alarm

7. Tamper

Fault

11. Technical, 12. Transmission path fault, 14. Aux mains

fault, 15. Aux batt fault

Custom type 1

Not allowed [3]

Selectable

Custom type 2

Not allowed [3]

Selectable

[1] Zones of particular types do not activate camera. These are 8. Exit terminator, 9. Keyswitch,

17. Eng. reset. When an assigned zone is one of the listed types, it is ignored when active.

[2] If the camera has been activated by a standard reporting event, another event caused by

camera activation does not occur.

Detailed codes and subevent values are described in Advisor Advanced Programming

Manual.

[3] Custom type events can only be activated by condition filters.

Each of these types can be configured in “2.2.2.n.4.09.1 Pic settings” on page 7.

Depending on camera event type, the camera can be programmed to take a

single picture or a series of pictures, in low or high resolutions.

4 PIR Camera Reference Manual

Application example

Figure 2 below shows an example of wireless PIR camera application.

Figure 2: Application example

(1) Intrusion zone 3, PIR camera 3

(2) Access zone 2, PIR camera 2

(3) Entry/exit zone 1, door contact

(4) Intrusion zone 5, PIR camera 5

(5) Intrusion zone 4, door/window sensor

(6) Intrusion zone 6, door/window sensor

In the example above, camera 3 (item 1) is activated not only by built-in PIR

camera, but also by zones 4 (item 5) and 2 (item 2). This makes possible taking

pictures of the intruder escape path.

ATS1238 expander

PIR Camera expands Advisor Advanced control panel inputs with 868 MHz AM

wireless transmitter sensors.

ATS1238 also supports wireless PIR cameras. For intrusion alarm events the

868 MHz AM connection is used. The additional camera video verification

functionality uses the 2.4 GHz connection.

Fob buttons can be programmed to set and unset premises, or to control relays.

For example, a fob can be used to open and close a garage door remotely.

ATS1238 supports maximum 8 wireless PIR cameras and sensors (total of 32)

and 16 fobs. ATS1238 expands the panel with 32 zones.

Note: Only one ATS1238 can be connected to the control panel. Install ATS1235

expanders to increase number of sensors and fobs.

ATS1238 requires the following ATS Advanced control panel firmware versions:

MR_022.022.0110 or later.

(1) (2) (3) (4)

(5) (6)

PIR Camera Reference Manual 5

The wireless expander is powered from the Advisor Advanced control panel MI

bus.

Installation

ATS1238 is mounted inside Advisor Advanced large plastic housing.

WARNING: Electrocution hazard. To avoid personal injury or death from

electrocution, remove all sources of power and allow stored energy to discharge

before installing or removing equipment.

Refer to ATS1238 Advanced Wireless DGP Installation Sheet for details on

installation and address setting.

Programming

The ATS1238 expander is programmed using the Advisor Advanced control

panel programming menu. Refer to Advisor Advanced Programming Manual for

details.

To activate the expander, use the Devices submenu of the Advisor Advanced

programming menu. See “Programming menus” on page 7 for details.

Wireless PIR camera

Description

A wireless PIR camera is a wireless PIR detector with a camera built-in. The

camera can be programmed to take pictures in case of activation of associated

zones, conditional filters, as well as by manual activation or remote requests.

See “Camera activation” on page 2 for more details.

Installation

The PIR camera is intended to be mounted on walls but can also be mounted on

ceilings by using a mounting bracket.

Use the following guidelines to determine the best location to install the PIR

camera.

•Mount the PIR camera so the expected movement of an intruder is across the

detection pattern.

•Mount the PIR camera at a stable surface at a height between 1.8 m and

3.0 m from the floor.

•Do not mount the PIR camera within 0.5 m of metallic objects or within 1.5 m

of fluorescent lights.

•Do not place objects in front of the PIR camera that may prevent a clear line

of sight.

•Place PIR cameras at least 1 m apart from each other.

Avoid potential causes of instability, such as:

•Direct sunlight on the detector

6 PIR Camera Reference Manual

•Heat sources within the detector field of view

•Strong air draughts onto the detector

•Animals in the field of view

•Obscuring the detector field of view with large objects, such as furniture

We recommend that the PIR camera is regularly walk tested and checked at the

control panel.

Programming

Wireless PIR camera is programmed using the Advisor Advanced programming

menu.

How to program a camera:

1. Program the wireless PIR camera expander. See “ATS1238 expander” on

page 4 for more details.

2. Program a wireless PIR camera as a wireless PIR detector. See

“Programming menus specific for PIR camera” on page 7 for more details.

If the detector is programmed successfully, the appropriate camera is created

automatically. The created camera number is equal to the zone number of the

wireless PIR detector.

3. Program the camera options. See “4.3 Cameras” on page 10.

4. Assign zones to the camera. Choose up to four zones. The camera is useful if

its field of view covers these zones or possible burglar escape paths from

there.

By default, the first assigned zone is the zone of the wireless detector built in

the configured wireless PIR camera.

5. If necessary, program conditional event filters that activate the camera.

6. If necessary, program reporting events that activate the camera.

Troubleshooting

Camera busy message

Camera busy message may appear when a camera or a wireless expander do

not respond to a request because one the following operations is currently in

progress:

•Erasing picture memory on the wireless expander

•Running RSSI test

•Running RF diagnostic test

•Running range test

•Setting camera mode (for example, unsetting the system

•Taking pictures according to other request

•Running walk test

•Learning in camera

•Updating current state (occurs for 2 to 3 s every 17 minutes)

PIR Camera Reference Manual 7

Solution: repeat the request after a delay of a few seconds.

Camera error message

Camera error message appears due to one of the following states:

•Processing another request for longer than 20 s (for example, reporting

pictures for previous request for this camera)

•Communication failed

Solutions:

•Repeat the request in a few minutes

•Verify power supply

•Verify communication quality

See also “Camera diagnostics” on page 16.

Programming menus specific for PIR camera

2.1 Installed remote devices

>Rkp R--x----

Exp m--?---

The Installed remote devices screen shows the status of all connected remote

keypads (1 to 8) and expanders (1 to 7).

The following statuses are shown if an ATS1238 expander is connected to the MI

bus:

•M: ATS1238 is online and configured (polled)

•m: ATS1238 is online, but not configured (new)

•c: ATS1238 is online, but its address is in conflict with another expander

To configure an expander shown as “m”, press Enter. Otherwise, solve the

connection problem.

2.2.2.n.4.09 Pic options

1>Pic settings

>>>

This menu is specific for systems with wireless PIR camera expanders.

2.2.2.n.4.09.1 Pic settings

1>Burglar set.

>>>

The menu allows you to configure photo recording options separately for the

following camera event types:

•Burglar alarms

•Fire alarms

•Panic alarms

•Medical alarms

8 PIR Camera Reference Manual

•Tamper alarms

•Faults: Device faults and technical alarms

•Custom type 1: User programmable type 1

•Custom type 2: User programmable type 2

See also “Camera event types” on page 3.

2.2.2.n.4.09.1.1 Burglar settings

1>Pic amount

Enter the BA settings menu to configure picture settings for burglar alarms.

2.2.2.n.4.09.1.1.1 Pic amount

1 Pic amount

>1<

Set the number of pictures taken after an event of the selected type occurs.

Allowed range is 1 to 30. The delay between pictures is set in “2.2.2.n.4.09.1.1.2

Frame rate” below.

2.2.2.n.4.09.1.1.2 Frame rate

2 Frame rate

>500 ms<

The menu defines a frequency of taking pictures on an event of the selected

type.

The menu is only available if “2.2.2.n.4.09.1.1.1 Pic amount” above value is

larger than 1.

The allowed values are 500 ms, 1 s, 5 s, 15 s, 60 s.

2.2.2.n.4.09.1.1.3 Pic quality

3 Pict quality

>QVGA<

The option defines resolutions of pictures taken upon an event of the selected

type. The following options are available:

•QVGA: 320 x 240 pixels

•VGA: 640 x 480 pixels

•QVGA and VGA: Two pictures at once, one in low resolution, and one in high.

2.2.2.n.4.09.1.2 Fire settings

2.2.2.n.4.09.1.3 Panic settings

2.2.2.n.4.09.1.4 Medical settings

2.2.2.n.4.09.1.5 Tamper settings

PIR Camera Reference Manual 9

2.2.2.n.4.09.1.6 Fault settings

See “2.2.2.n.4.09.1.1 Burglar settings” on page 8.

2.2.2.n.4.09.1.7 Custom type 1

2.2.2.n.4.09.1.8 Custom type 2

Custom types are used with condition filters for camera activation.

See “2.2.2.n.4.09.1.1 Burglar settings” on page 8.

2.2.2.n.4.09.2 Show pic mem

Pictures: 12

Left sp for: 123

Free SP: 3,0MB

Total SP: 4,0MB

The informational screen shows a pictures number currently stored in the

wireless PIR camera expander as well as available memory.

2.2.2.n.4.09.3 Pic auto deletion

3 Pic auto del

>1 day<

The value defines whether the pictures stored in the wireless PIR camera

expander will be deleted automatically after a chosen period of time (in days).

The allowed range is 1 to 120 days. 0 or Off mean that pictures are never deleted

automatically. Users must control the available memory and remove pictures

manually.

2.2.2.n.4.09.4 Delete pics

4 Delete pics

>Cancel<

Choose OK and press Enter to remove all stored pictures from the wireless PIR

camera expander.

4.1.0 Add zone

To add a wireless PIR camera, follow these steps.

1. Select zone location.

1>Expander 1

2 Expander 2

2. Choose Sequential mode and press Enter.

Learn mode

>Sequential<

10 PIR Camera Reference Manual

3. Choose an input number.

Input number

> 2<

4. Remove the PIR camera from mounting plate to activate it.

INFO

Tamper RF 1

If an error occurs, the keypad shows an error message and beeps seven times.

Example:

ERROR

RF duplicate

The error can occur, for example, when you try to learn a device, which is

already programmed in the wireless expander. See “Camera unregistering”

below for details.

Next you are asked if you want to edit the new zone.

Edit zone?

>No<

Chose Yes and press Enter to edit zone settings.

You are also asked to edit settings of the created camera.

Edit camera?

>No<

If the device is programmed successfully, the keypad beeps twice.

Camera unregistering

Note: Once learned, the PIR camera cannot be learned on another wireless

expansion without prior unregistering from a previous expansion. To unregister

the PIR camera, revert it to the factory settings by following these steps:

1. Remove the PIR camera from mounting plate.

2. Insert factory setting jumper.

3. Remove batteries.

4. Wait 10 seconds.

5. Insert batteries.

6. Wait approximately 3 seconds until the PIR camera powers up.

7. Remove the factory setting jumper and mount the PIR camera.

After that, the PIR camera is defaulted and ready for learning in.

4.3 Cameras

17>Camera 17

18 Camera 18

The menu allows you to configure camera modules in wireless PIR cameras.

Indice

Altri manuali Interlogix Telecamera di sicurezza

Interlogix

Interlogix TruVision TVD-N210V-2-N(-P) Manuale utente

Interlogix

Interlogix TruVision IP Dome Manuale utente

Interlogix

Interlogix TruVision TVB-2402 Manuale utente

Interlogix

Interlogix UVD-XP4DNR(-P) Manuale utente

Interlogix

Interlogix UltraView UVD-6130VE-2-P Manuale utente

Interlogix

Interlogix TruVision TVB-2401 Manuale utente

Interlogix

Interlogix MobileView MVC-7100-29-BL Manuale utente

Interlogix

Interlogix TruVision TVW-2401 Manuale utente

Interlogix

Interlogix TVW-1120 Manuale utente

Interlogix

Interlogix TruVision Line Manuale utente

Interlogix

Interlogix UltraView IP PTZ 36X Manuale utente

Interlogix

Interlogix TVD-6120VE-2-N Manuale utente

Interlogix

Interlogix UVC-XP4DN-HR Manuale utente

Interlogix

Interlogix TruVision PTZ 36X Manuale utente

Interlogix

Interlogix TVC-5120-1 Manuale utente

Interlogix

Interlogix UVC-XP4DN-HR Manuale utente

Interlogix

Interlogix UltraView UVC-6130-1-N Manuale utente

Interlogix

Interlogix UVD-XP4DNR(-P) Manuale utente

Interlogix

Interlogix TruVision Open Standards Manuale utente

Interlogix

Interlogix UVD-XP4DNR(-P) Manuale utente

Interlogix

Interlogix TruVision TVA-1101 Manuale utente

Interlogix

Interlogix TruVision TVB-2401 Manuale utente

Interlogix

Interlogix TruVision TVD-2401 Manuale utente

Interlogix

Interlogix TruVision TVD-2401 Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente