Intersil ISL32741EVAL1Z Manuale utente
Rev 1.00 Aug 2017
User’s Manual
ISL32741EVAL1Z
User’s Manual: Evaluation Board
Industrial Precision
UG126 Rev.1.00 Page 2 of 10
Aug 24, 2017
UG126
Rev.1.00
Aug 24, 2017
ISL32741EVAL1Z
Evaluation Board
USER’S MANUAL
1. Overview
The ISL32741EVAL1Z board enables the evaluation of the ISL32741EIBZ reinforced isolated, half-duplex RS-485
transceiver in a typical bus node application, used in isolated industrial networks.
1.1 Key Features
• Drive capability of up to 160x1/5UL-transceivers
• Isolated 3.3V to 5V DC/DC converter with regulated output
1.2 Specifications
This board has been configured and optimized for the following operating conditions:
• Up to 40Mbps data rate
•V
CC = 3.3V
1.3 Ordering Information
1.4 Related Literature
• For a full list of related documents, visit our website
•ISL32741E product page
Figure 1. Block Diagram
Part Number Description
ISL32741EVAL1Z ISL32741EIBZ evaluation board
LOGIC
I/O
RS-485
I/O
3.3V
SUPPLY
J5J2
J1
ISL32741EIBZ
ISOLATED
RS-485
TRANSCEIVER
ISOLATED
DC-DC
CONVERTER
5V
3
UG126 Rev.1.00 Page 3 of 10
Aug 24, 2017
ISL32741EVAL1Z 2. Functional Description
2. Functional Description
The ISL32741E is a reinforced isolated, 40Mbps, half-duplex RS-485 transceiver. The device incorporates a patented
refresh circuit to maintain the correct output state with respect to data input. At power-up, the bus outputs follow the
tables in “Truth Tables”.
The DE input should be held low during power-up to prevent false drive data pulses on the bus. This is accomplished
by connecting DE through a 10kΩ pull-down resistor to GND1.
This transceiver uses a differential input receiver for maximum noise immunity and common-mode rejection. Input
sensitivity is ±200mV, as required by the RS-485 specification.
The receiver input resistance is 54kΩ minimum. The receiver includes a “full fail-safe” function that ensures a high-
level receiver output if the receiver inputs are unconnected (floating) or shorted. The receiver output is tri-statable
through the active low RE input.
The driver is a differential output device that delivers at least 2.1V across a 54Ω purely differential load. The driver
features low propagation delay skew to maximize bit width and to minimize EMI.
The driver in the ISL32741E is tri-statable through the active high DE input. The outputs of the ISL32741E driver are
not slew rate limited, so faster output transition times allow data rates of at least 40Mbps.
Important Notice:
For convenience, an isolated DC/DC converter is used to provide the power supply across the isolation barrier. Its
isolation ratings however, are lower than those of the transceiver. Therefore, ensure that the ground potential difference
between the left side (GND1, GND2) and the right side (GND3, GND4) of the board remain below 50VAC (see
Figure 2).
2.1 Truth Tables
Receiving
Inputs Output
RE DE A-B RO
00 V
AB ≥ -0.05V 1
0 0 -0.05V > VAB > -0.2V Undetermined
00 V
AB ≤ -0.2V 0
0 0 Inputs Open/Shorted 1
1 1 X High-Z
1 0 X High-Z*
Transmitting
Inputs Outputs
RE DE D ISODE B A
X11101
X10110
0 0 X 0 High-Z High-Z
1 0 X 0 High-Z* High-Z*
Note: *Transceiver shutdown mode
UG126 Rev.1.00 Page 4 of 10
Aug 24, 2017
ISL32741EVAL1Z 3. PCB Layout Guidelines
3. PCB Layout Guidelines
Both supplies, VDD1 and VDD2, must be bypassed with 100nF ceramic capacitors. These should be placed as close as
possible to the supply pins for proper operation.
3.1 ISL32741EVAL1Z Evaluation Board
Figure 2. Top Side
Figure 3. Bottom Side
UG126 Rev.1.00 Page 5 of 10
Aug 24, 2017
ISL32741EVAL1Z 3. PCB Layout Guidelines
3.2 ISL32741EVAL1Z Circuit Schematic
Figure 4. ISL32741EVAL1Z Schematic
ISL32741EIBZ
UG126 Rev.1.00 Page 6 of 10
Aug 24, 2017
ISL32741EVAL1Z 3. PCB Layout Guidelines
3.3 Bill of Materials
Manufacturer Part Qty
Reference
Designator Description Manufacturer
ISL32741EVAL1ZREVAPCB 1 PWB-PCB, ISL32741EVAL1Z, REVA, ROHS Imagineering Inc
ISL32741EIBZ 1 U1 6KV REINFORCED ISOLATED, 40Mbps,
HALF-DUPLEX RS-485 TRANSCEIVER, ROHS
Intersil
R1Z-3.305/P 1 U2 ISOLATED 3.3V-TO-5V DC/DC CONVERTER WITH
REGULATED OUTPUT, ROHS
RECOM-POWER
CR0805-8W-
1002FT(PbFREE)
4 R1 - R3, R7 RES, SMD, 0805, 10k, 1/8W, 1%, TF, ROHS Venkel
RK73H2AT1330F 1 R5 RES, SMD, 0805, 133Ω, 1/8W, 1%, TF, ROHS KOA
RC0805FR-07549RL 2 R4, R6 RES, SMD, 0805, 549Ω, 1/8W, 1%, TF, ROHS Yageo
C0805X5R160-106KNE 2 C1, C3 CAP, SMD, 0805, 10µF, 16V, 10%, X5R, ROHS Venkel
ECJ-2VB1E104K 2 C2, C4 CAP, SMD, 0805, 0.1µF, 25V, 10%, X7R, ROHS Panasonic
1725656 1 J1 CONN-TERMINAL BLK, TH, 2P, 6A, 125V,
20-30AWG, 2.54mm, ROHS
Phoenix Contact
1725672 2 J2, J5 CONN-TERMINAL BLOCK, 4POS, 0.1, 26-20AWG,
63V, 6A, ROHS
Phoenix Contact
5001 4 GND1 - GND4 CONN-MINI TEST PT, VERTICAL, BLK, ROHS Keystone
5003 6 A, B, D, R, DE, RE# CONN-MINI TEST POINT, VERTICAL, ORG, ROHS Keystone
S-2261 1 Place assy in bag BAG, STATIC, 4x6, ZIPLOC, ROHS ULINE
LABEL-DATE CODE 1 AFFIX TO BACK OF
PCB
LABEL-DATE CODE_LINE 1: YRWK/REV#, LINE 2:
BOM NAME
Intersil
UG126 Rev.1.00 Page 7 of 10
Aug 24, 2017
ISL32741EVAL1Z 3. PCB Layout Guidelines
3.4 Board Layout
Figure 5. Silkscreen Top Figure 6. Top Layer
Figure 7. Silkscreen Bottom Figure 8. Bottom Layer
UG126 Rev.1.00 Page 8 of 10
Aug 24, 2017
ISL32741EVAL1Z 4. Typical Performance Curves
4. Typical Performance Curves
Figure 9. Transmit Mode Figure 10. Receive Mode
Figure 11. Transmit Mode Figure 12. Receive Mode
DI
A
B
TIME: 80ns/DIV
SIGNAL: 2V/DIV
A
B
TIME: 80ns/DIV
SIGNAL: 2V/DIV
RO
DI
A
B
TIME: 10ns/DIV
SIGNAL: 2V/DIV
RO
A
B
TIME: 10ns/DIV
SIGNAL: 2V/DIV
ISL32741EVAL1Z 5. Revision History
Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the
reader is cautioned to verify that the document is current before proceeding.
For information regarding Intersil Corporation and its products, see www.intersil.com
© Copyright Intersil Americas LLC 2017. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
UG126 Rev.1.00 Page 9 of 10
Aug 24, 2017
5. Revision History
Rev. Date Description
1.00 Aug 24, 2017 Updated the truth tables on page 3.
0.00 May 31, 2017 Initial release
ISL32741EVAL1Z
UG126
Indice
Altri manuali Intersil Scheda madre
Intersil
Intersil ISL97656IRTZEVALZ Istruzioni per l’uso
Intersil
Intersil ISL6296 Istruzioni per l'installazione e il funzionamento
Intersil
Intersil ISL70003ASEHEV2Z Manuale utente
Intersil
Intersil ISL76683 Manuale utente
Intersil
Intersil ISL71010BM25EV1Z Manuale utente
Intersil
Intersil ISL68200 Series Manuale utente
Intersil
Intersil ISL9000A Manuale utente
Intersil
Intersil ISL8500EVAL1Z Istruzioni per l'installazione e il funzionamento
Intersil
Intersil ISL78205EVAL1Z Manuale
Intersil
Intersil ZL6100EVAL2Z Istruzioni per l'installazione e il funzionamento
Intersil
Intersil ISL2827xINEVAL1Z Manuale utente
Intersil
Intersil ISL9120IIx-EVZ Manuale utente
Intersil
Intersil ISL6560 Istruzioni per l'installazione e il funzionamento
Intersil
Intersil ISL75051ASEHEV1Z Manuale utente
Intersil
Intersil HIP4086 Manuale utente
Intersil
Intersil ISL70244SEHEV1Z Manuale utente
Intersil
Intersil ISL71831SEH Manuale utente
Intersil
Intersil QHx220 Manuale di installazione
Intersil
Intersil ISL73033SLHEV1Z Manuale utente
Intersil
Intersil ISL8014AEVAL2Z Istruzioni per l'installazione e il funzionamento
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
