IPEX CABLINE-CAF Manuale utente

1/ 13

Document No.

HIM

8016

Confidential C

PEX Inc. QKE

DFFDE09

03 REV.8

CABLINE®-CAF

Part No.3437-0**1 (SHELL Only), 20858-0**T-01 (SHELL ASS’Y)

Instruction Manual

2 S20346 July 10, 2020 R.Fukuda M.Muro Y.Shimada

1 S19185 March 28, 2019 K.Hara T.Masunaga Y.Shimada

0 S18460 July 27, 2018 Y.Sasa T.Masunaga H.Ikari

Rev. ECN Date Prepared by Checked by Approved by

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

2/ 13

Confidential C

弊社、CABLINE-CAF CONN.の取り扱いに際して、本コネクタを安全に御使用頂くことを目的とし、

コネクタの挿入・抜去の手順及び注意点を記述致します。

This manual outlines how to correctly mate and unmate CABLINE-CAF connectors, as well as precautions for proper handling of the product.

【対象コネクタ名称・型番】 / Connector Name, Part number

◆FPC 側コネクタ (FPC side connector)

名称 / Product Name ：CABLINE-CAF PLUG

型番 / Part No. ：20858-0**T-01 ・・・・・・・ SHELL ASS’Y (With LOCK BAR)

3437-0**1 ・・・・・・・ SHELL (Without LOCK BAR)

◆基板側コネクタ (PCB side connector)

名称 / Product Name ：CABLINE-CA RECEPTACLE

型番 / Part No. ：20525-※**E-※※※

“＊＊”には各芯数番号が入ります。

“**”: Connector pin count.

“※”はバリエーションになります。詳細は図面を参照願います。

“※”: Connector variation type. Refer to the drawing for the details.

【コネクタ各部名称】 Labelled diagram of the connector

図1(Fig. 1) Connector parts names

FPC 側コネクタ

PLUG

基板側コネクタ

Receptacle

I-PEX MARK

嵌合基準マーク

Datum pin mark

LOCK BAR

嵌合方向

Mating direction

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

3/ 13

Confidential C

【コネクタ挿入手順 / How to mate connectors】

1．FPC 側コネクタのセット方法（Direction to mate.）

図2のように、基板側コネクタの基準 pin にFPC 側コネクタの基準 pin がくるように、セットします。

As shown in Fig.2, please set plug so that the datum pin mark of the plug connector and the receptacle connector are matched.

図2（Fig.2）

2．嵌合方法(How to mate.)

図3のように、FPC を水平に押し、ロック穴にロックが掛かると、嵌合完了となります。

As shown in Fig.3, push FPC horizontally until it is locked.

図3（Fig.3）

SHELL (LOCK BAR 無し)の場合 / For the connector SHELL(Without LOCK BAR).

FPC を水平に挿入する

Insert FPC to the connector horizontally.

ロックが掛かっている事を確認

Check if it is locked.

FPC 側コネクタ基準 pin

Datum pin of plug connector.

ロックが掛かっている事を確認

Check if it is locked.

基板側コネクタ基準 pin

Datum pin of receptacle connector.

隙間がないか確認

Confirm whether there is space.

⇒

Rece shell

I-PEX MARK

Plug shell

Plug shell とRece shell がオーバーラップ

している事を確認

Check the overlap of Plug shell and Rece shell.

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

4/ 13

Confidential C

注意事項 / Cautions.

片側ずつ押すと、隙間が発生する恐れが有ります。（図 4）

When you push one end it might cause half mating. （Fig.4）

図4（Fig.4）

隙間発生 NG 状態

There is gap. NG

片側挿入 1

Push the one side.

片側挿入 2

Push the one side.

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

5/ 13

Confidential C

SHELL ASS’Y(LOCK BAR 付)の場合 / For the connector SHELL ASS’Y(With LOCK BAR).

1．FPC 側コネクタのセット方法 (How to place plug connector）

図5のように基板側コネクタの基準 pin にFPC 側コネクタの基準 pin がくるようにセットする。

Place the plug and receptacle so that their datum pin marks are aligned. [Fig. 5]

2．嵌合方法 (How to mate connectors.)

①：図 6のように仮挿し状態時に、LOCK BAR を基板側コネクタ側にロックしない程度に回転させ、FPC を水平に押す。

そして、突き当て面に隙間がないか確認する。

Insert plug into receptacle. Slightly rotate the lock bar toward receptacle but do not lock it yet.

Push the FPC horizontally until it is fully inserted. Make sure that connectors are completely mated. [Fig. 6]

②：図 7のように嵌合完了後、LOCK BAR を基板側に押し込み、基板側コネクタの SHELL とロックさせる。

Push down the lock bar to hook receptacle shell to lock connectors. [Fig. 7]

基板側コネクタ基準 pin

Datum pin mark on receptacle connector

FPC 側コネクタ基準 pin

Datum pin mark on plug connector

I-PEX mark

図5 (Fig. 5) Aligned datum pin marks on plug and receptacle

図6(Fig. 6) Inserting FPC

図7(Fig. 7) Locking lock bar

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

6/ 13

Confidential C

※嵌合後確認内容 (Mating check points)

※注意 (Cautions)

Ⅰ：図 9のように挿入時に LOCK BAR を押しながら挿入すると、LOCK BAR が変形したり、

回転軸がコネクタから抜ける恐れがありますので、行わないでください。

Do not push the lock bar while inserting connector, as this may deform the lock bar or rotation axis may fall off from the connector.

Make sure to hold FPC for proper insertion. [Fig. 9]

Ⅱ：図 10 のように片側ずつ押すと、隙間が発生する恐れが有ります。

Do not push one side of the plug shell or the gap may cause improper mating. [Fig. 10]

ロックが掛かっている事を確認

Make sure that locks are hooked

隙間がないか確認

No gap

図8Fig. 8 Checking points of the proper mating

図10(Fig. 10) Improper way to push plug

片側挿入 1

Do not push one end

隙間発生 NG 状態

Gap indicates bad mating

片側挿入 2

Do not push the other end

図9(Fig.9) Do not push lock bar to mate connectors

LOCK BAR をコネクタの挿入に

使用しないでください。

Do not push lock bar to mate

connectors.

回転軸

Rotation axis

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

7/ 13

Confidential C

Ⅲ：本コネクタを安全に使用して頂く為に、図 11 の様にこじり角を 3°以下で御願い致します。仮差しの状態から片側のみを

挿入した場合、下図の様にこじり MAX.値が 5°となります。5°以下であればコネクタの変形は発生致しません。

Do not exceed 3° when inserting plug connector to use this connector safely. If one end of the connector was inserted

at presetting position, maximum slanted angle will be 5°. As long as the angle is within 5°, damages will not occur. [Fig. 11]

Ⅳ：コネクタ挿入開始時の許容角度は図 12 に示すように 8°です。

Do not exceed 8° when inserting plug connector. [Fig. 12]

Ⅴ：図 13 のように、RECE. SHELL に挿入ガイドが設定されています。ガイドに沿って挿入を御願い致します。

ガイドに沿って挿入頂ければコネクタの変形は発生致しません。

Insert the plug along the insertion guards inside the receptacle shell. These guards protect from connector damages. [Fig. 13]

5°

図11(Fig. 11) Maximum mating slanted angle

図13(Fig. 13) Insertion guards inside receptacle shell

図12(Fig.12) Maximum inserting angle

8°

SHELL 裏面のガイド形状

Insertion guards

inside receptacle shell

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

8/ 13

Confidential C

【コネクタ抜去手順 / Two ways to unmate connectors. 】

・コネクタを抜去する。Un-mating the connector.

図14 のように基板側コネクタに対し、FPC 側コネクタの FPC を矢印方向に平行に抜去する。

斜めに抜去すると、FPC の変形又は FPC のパターンにダメージを与える恐れがあります。

As shown in Fig.14, please pull out plug connector horizontally to PCB, slanted un-mating might

cause deformations of FPC or damage on FPC pattern.

平行抜去 OK 状態 / horizontal un-mating , OK condition

図14（Fig.14）

こじり抜去 NG 状態 / Slanted un-mating, NG

図15 (Fig. 15)

5°以下であればコネクタの変形は発生致しません。

To use this connector safely, please withdraw plug up to at 5° degree slanted angle as shown in the figure below.

so that it will not have deformation.

5°こじり状態 / 5°slanted un-mating status

図16 (Fig. 16)

SHELL (LOCK BAR 無し)の場合 / For the connector SHELL(Without LOCK BAR).

FPC を水平に引っ張る

Withdraw FPC from connector horizontally

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

9/ 13

Confidential C

ここでは 2種類の抜去方法を説明しております。コネクタのご使用状態に応じて、抜去方法をご選択ください。

There are two ways to unmate connectors. Select the method you prefer based on your connectors mounted position.

Method 1: FPC 掴み抜去 / By pulling FPC

図17 の①の箇所のどちらか一方を②の方向に LOCK BAR を上げ、基板側コネクタとのロックを解除後、③の方向に

LOCK BAR を回転させる。抜去は基板側コネクタに対し、FPC 側コネクタの FPC を④の方向に平行に抜去する。

Select one end of the lock bar circled in ①in figure 17. Push up the selected side of the lock bar upward as shown

in ②direction to release the lock. Rotate the lock bar toward FPC, indicated as ③direction.

Slide the FPC horizontally to remove the plug from receptacle. [Fig. 17]

SHELL ASS’Y(LOCK BAR 付)の場合 / For the connector SHELL ASS’Y(With LOCK BAR).

③

絶縁コート部 / Insulated part

①

②

図17(Fig. 17) Pulling FPC to unmate connectors

④④

CABLINE

CAF

Instruction Manual

Document No.

HIM

8016

10 / 13

Confidential C

Method.2: LOCK BAR 掴み抜去 / By pulling lock bar

図18 に示す①の箇所のどちらか一方を、②の方向に上げ、基板側コネクタとのロックを解除する。その後、

垂直になるように LOCK BAR を回転させ、③の箇所を掴んで矢印方向に、基板と水平になるように抜去する。

Select one end of the lock bar circled in ①in figure 18. Push up the selected side of the lock bar to release the lock.

Rotate the lock bar until it is vertical. Pull the lock bar circled in ③horizontally against PCB until the connectors

are unmated. [Fig. 18]

②

図18(Fig. 18)Pulling lock bar to unmate connectors

③③③

絶縁コート部 / Insulated part

①

Altri manuali per CABLINE-CAF

Questo manuale è adatto per i seguenti modelli

Altri manuali IPEX Cavi e connettori

IPEX

IPEX CABLINE-CBL PLUG Manuale utente

IPEX

IPEX CABLINE-VSF Manuale utente

IPEX

IPEX CABLINE-CX II With Cover Manuale utente

IPEX

IPEX EVAFLEX 5-HD Manuale utente

IPEX

IPEX 20613-0 E-0 Series Manuale utente

IPEX

IPEX MHF I Manuale utente

IPEX

IPEX FPL II Manuale utente

IPEX

IPEX MHF 7S Manuale utente

IPEX

IPEX CABLINE-UM PLUG Manuale utente

IPEX

IPEX CABLINE-UM Manuale utente

IPEX

IPEX CABLINE-CAL Manuale utente

IPEX

IPEX EVAFLEX 5-SE-GHT Manuale utente

IPEX

IPEX MINIFLEX 5-BF II Manuale utente

IPEX

IPEX CABLINE-VS PLUG Manuale utente

IPEX

IPEX CABLINE-VS IIF Manuale utente

IPEX

IPEX MP-A01 Manuale utente

IPEX

IPEX MINIFLEX 175-ST Manuale utente

IPEX

IPEX ISH Series Manuale utente

IPEX

IPEX CABLINE-VS Manuale utente

IPEX

IPEX CABLINE-CAL PLUG Manuale utente

IPEX

IPEX MP-A 03 Manuale utente

IPEX

IPEX CABLINE-VS IIF Manuale utente

IPEX

IPEX MINIFLEX 2-BF Manuale utente

IPEX

IPEX ISH Manuale utente

Manuali Cavi e connettori popolari di altre marche

Philips

Philips SWA6310 Manuale utente

StarTech.com

StarTech.com CRJ4550PK Manuale utente

Nohau

Nohau EMUL-IP2K-PC Manuale utente

Foxun

Foxun SX-SP144E-HD4K2K Manuale utente

Philips

Philips SWA3305W Manuale utente

opticis

opticis Stretch DVIM1-1P0x Manuale utente

Volkswagen

Volkswagen VAS 6558A Manuale utente

NEXIBO

NEXIBO N-13 Manuale utente

CYP

CYP PU-1H3HBTL Manuale utente

Allen-Bradley

Allen-Bradley 1784-u2dhp Manuale utente

Global Caché

Global Caché Flex Link Blaster Manuale utente

Hauppauge

Hauppauge USB-Live2 Manuale utente

Fenix

Fenix MPSV 15 Manuale utente

BEGA

BEGA 71 085 Manuale utente

Tesla

Tesla HPWC Manuale utente

GAMERON

GAMERON LUXURY TV CABLE Manuale utente

molex

molex Milli-Grid Dual row 87568 Series Manuale utente

Burndy

Burndy Continental Industries thermOweld CRE-7 Manuale utente