IWILL DP6NS Manuale utente

EC Declaration of Conformity

Iwill Corp.

No. 9-1, Kong 6th RD.,

Lin Kou 2nd Industrial

Park, Taipei, Taiwan R.O.C.

declare under sole responsibility that the

DP6NS motherboard

meets the intent of Directive 89/336/ECC for Electromagnetic Compatibility.

Compliance was demonstrated to the following specifications as listed in the

official Journal of the European Communities:

EN 50081-1 Emissions:

EN 55022 Radiated, Class B

EN 55022 Conducted, Class B

EN 60555-2 Power Harmonics

EN 50082-1 Immunity:

IEC 801-2 Electrostatic Discharge

IEC 801-3 RF Radiat

IEC 801-4 Fast Transient

About This Manual

This manual will guide both of experienced / beginner users in quick / detail

installation the system. There are six chapters in this manualand step by step

description will clearly guides you how to install the system.

User who is experienced in assembling system may refer to chapter 0 for quick

installation. Start from chapter one for detail description and engineer design

concept if you feel you are not qualified.

This manual is subject to change without notice.

This manual contains information protected by copyright law. All rights are

reserved. No any part of this document may be used or reproduced in any forms

or by any means, or stored in a database or retrieval system, without prior written

permission.

Trademark

Intel / Pentium is trade mark of Intel Corporationand all other product namesaretrademarksand

registered trademarksof their respective owners.

Contents

Chapter O - Quick lnstallation P4

Chapter 1- Overview

1.1 Features P14

1.2 Specifications P17

Chapter 2- Quick Installation P18

Chapter 3- Hardware Installation P19

3.1 Preparation and Inspection P19

3.2 Placement P20

3.3 CPU group P22

3.4 D-RAM Configuration P24

3.5 SCSI Interface P26

3.6 RAIDBUS P31

3.7 IDE Interface P31

3.8 USB P32

3.9 Enhanced Multi-IO P34

3.10 Other P36

Chapter 4- ATX Form-Factor Overview P39

Chapter 5- Award BIOS Setup P42

5.1 Main Menu P45

5.2 Standard CMOS Setup P49

5.3 BIOS Features Setup P53

5.4 Chipset Feature Setup P58

5.5 Power Management Setup P65

5.6 PNP/PCI Configuration setup P69

5.7 Integrated Peripherals P72

5.8 Load Setup Defaults P75

5.9 Supervisor/User Password setting P76

5.10 IDE HDD Auto Detection P77

5.11 HDD Low Level Format P77

5.12 Save & Exit Setup P77

5.13 ExitWithout Saving P77

Chapter 6- SCSI BIOS Setup

6.1 When to Use the SCSI Select Utility P78

6.2 SCSI Select Utility option P79

6.3 Configure / View Host AdapterSettings P80

CHAPTER0

Quick Installation

Several easy installation steps will be described in this chapter to help the

experienced users for quick installation. If you are new user and need to know

more about this motherboard, please start from Chapter 1.

RAID

W. SCSI

U. SCSI

Socket 8

JP7

ISA

USB

PCI

SIMM

LPT

PS2

FAN

CPU

FDD

P. IDE

S. IDE

P. Control

BIOS

JP15

J10

J11

J12

J13

J14

Figure 1:Connectors for DP6NS

Socket 8

JP9

JP11

JP4

JP7

JP23

Figure 2 : Jumpers location

Connector Function Description

PW 20 pin Standard ATX power input connector

BIOS BIOS (Basic Input Output System)

CPU Two 387 pin Socket 8 CPU socket

FDD 34 pin Floppy Disk Drive with key protect connector

FAN Two Fan Power connector

LPT 25 pin Parallel D-Sub connector

ISA 4 x ISA(Industrial Standard Architecture) 98 pin expansion slot

SIMM SIMM Socket

J9 SIMM Socket(Single In-line Memory Module ) Bank 0

J10 SIMM Socket(Single In-line Memory Module ) Bank 0

J11 SIMM Socket(Single In-line Memory Module ) Bank 1

J12 SIMM Socket(Single In-line Memory Module ) Bank 1

J13 SIMM Socket(Single In-line Memory Module ) Bank 2

J14 SIMM Socket(Single In-line Memory Module ) Bank 2

JP15 2 pin power switch connector for ATX power supply

KB 6 pin PS2 keyboard Mini-DIN connector

P. IDE40 pin Primary IDE with key protect connector

S. IDE 40 pin Secondary IDE with key protect connector

PCI 3 x PCI version 2.1 compliance 120 pin PCI (Peripheral

Component Interface)expansion slot

RAID 60 pin extension slot for working with RAIDBUS 1130 adapter

P. Control Front panel signal control connector

RST—Reset Switch

SCSI—SCSI detect LED

IDE—IDE detect LED

SMI—System Management Interface switch

LED—Power-on LED

Speaker—Speaker connector

Keylock—Keylock switch connector

PS2 6 pin PS2 mouse Mini-DIN connector

S1 9 pin Serial 1 D-Sub connector

S2 9 pin Serial 2 D-Sub connector

U. SCSI 50 pin Ultra SCSI with key protect connector

USB 20 pin Universal Serial Bus connector

W. SCSI 68 pin Wide SCSI with key protect connector

Jumper Setting

JP2 3.3V Power Source Select

JP4 SCSI Chip Select

JP7 CPU Frequency Select

JP9 CMOS Clear Jumper

JP11 Flash EPROM Jumper Setting

JP12 Power-on switch type select

JP15 System On/Off Switch

JP23 Auto SCSI Terminator Control Function

Quick Installation

Step 1. Install Pentium Pro CPU

Pull up theCPU handlebar, place the CPU into the socket in

gentle/ horizontalway then pull down the handle barback to

its original place. There is no first or seond CPU socket if only

single Pentium Pro CPU is installed, you can insert the single

Pentium Pro CPU in either socket 8.

U. SCSI

Socket 8

U. SCSI

Socket 8

JP1

Socket 8

JP12

CPU

Step 2. Install Pentium Pro CPU Cooler

Hook the CPU Cooler’s metal la tch one side to the CPU

socket’s peg, then press the meta l latch again to fit into

anotherside.

Warning: Care mustbe taken when the CPU Cooler was installed, if not

a suitable force might scrach this motherboardwhile you

install the cooler.

JP2 & JP12

+12V

GND

Control

Step 3. Adjust the CPU frequency

With the special patented design on this motherboard.Only

one jumperneeded to set this Pentium Pro CPU frequency.

Simply insert the jumper cap to the CPU frequency as it was

marked on top of the Pentium Pro CPU.Once the jumpercap

was inserted, it will automatically caculate the Internal/

External Clock and CLKMUL (Clock Multiplier).

U. SCSI

Socket 8

JP7

210

233

240

266

150

166

180

200

270

300

JP7

210

233

240

266

150

166

180

200

270

300

Step 4. Install the Memory Module

For at least two pieces of Fast Page Mode or EDO RAM with

72 pin SIMM (Single In-line Memory Module) must inserted

in this 64 bit Pentium Pro basemotherboard.TheJ9 to J14

were combined as Bank0,Bank1 and Bank2 in pair.

U. SCSI

Socket 8

BANK0

J10

J11

J12

J13

J14

BANK2

BANK1

Step 5. Install the Internal Peripherals

The internal peripherals meansdevices that in the computer

chassis like the Floppy Disk Drive, HardDisk Drive, CD ROM

Indice

Altri manuali IWILL Scheda madre

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente