Johnson Controls CKM-MR51E Istruzioni per il montaggio
24-10707-58 Revision E
December 2017
P2000
Security Management System
CKM-MR51E
authentic Mercury™ PoE module
hardware
installation
Copyright 2017
Johnson Controls
All Rights Reserved
No part of this document may be reproduced without the prior permission of Johnson Controls.
If this document is translated from the original English version by Johnson Controls, all reasonable
endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable
for any translation errors contained herein or for incidental or consequential damages in connection
with the furnishing or use of this translated material.
Due to continuous development of our products, the information in this document is subject to
change without notice. Johnson Controls shall not be liable for errors contained herein or for
incidental or consequential damages in connection with furnishing or use of this material. Contents
of this publication may be preliminary and/or may be changed at any time without any obligation to
notify anyone of such revision or change, and shall not be regarded as a warranty.
Other Manufacturers’ Documentation
Johnson Controls does not duplicate documentation of other equipment manufacturers. When
necessary, Johnson Controls provides documentation that supplements that of other manufacturers.
When unpacking your equipment, keep all original manufacturer documentation for reference.
Technical Support
For factory technical support, Johnson Controls authorized field technicians or authorized dealer
representatives can contact Global Security Solutions Technical Support by phone at
can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.
End users and customers should contact their local Johnson Controls branch or authorized dealer
for any of their support needs (technical support, maintenance contracts, on-site field support,
P2000 Software Service Agreements, Service Partnerships, and so on). Visit
http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.
For material returns contact the branch if the material was purchased through a Johnson Controls
branch or through the Product Sales Operations Team, if ordered through the Advanced Order
Management System (AOMS) and follow the RMA process; or contact the authorized dealer
representative where the material was purchased directly.
Single Point of Contact by Region
Acknowledgment
Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and
product names are trademarks or registered trademarks of their respective owners.
European Single Point of Contact
JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY
NA/SA Single Point of Contact
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
APAC Single Point of Contact
JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA
Declarations of Conformity
United States: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Canada: CAN ICES-3 (A)/NMB-3(A)
European Union: This product complies with the requirements of the EMC Directive.
This equipment must not be modified for any reason and it must be installed as stated in the
Manufacturer’s instruction. If this shipment (or any part thereof) is supplied as second-hand
equipment, equipment for sale outside the European Economic Area or as spare parts for either a
single unit or system, it is not covered by the Directives.
UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET
The following model number is listed under Underwriters Laboratories® (UL) 1076 for Proprietary
Burglar Alarm Units and Systems, UL 294 for Access Control Systems Units and Underwriters
Laboratories of Canada ULC/ORD-C1076-86.
CKM-MR51E
When installed at the site the following requirements must be met to comply with these standards.
1. The CKM-MR51E shall be mounted in Listed Enclosures CKM-CE75-E1M, CKM-CE75-
E2M, CKM-CE150-E4M, and Listed Burglar Alarm and Access Control System Units
SPE10000-1H00, SPH10000-1H00, SPF10000-1I00, SPF1I100-1I00 or SPF1I300-1J00.
2. A CKM-MR51E mounted in Listed Enclosures CKM-CE75-E1M, CKM-CE75-E2M, CKM-
CE150-E4M, and Listed Burglar Alarm and Access Control System Units SPE10000-
1H00,SPH10000-1H00, SPF10000-1I00, SPF1I100-1I00 or SPF1I300-1J00 shall be powered
through the CKM-F8P power distribution module.
3. Transient protection devices that are installed must not be removed or defeated.
4. Do not connect equipment to an AC power source that is controlled by a switch.
5. Mounting on a three-gang steel blank cover has not been investigated by Underwriters
Laboratories.
6. A 1.5Kohm/750ohm custom end-of-line resistance supervised circuit was investigated by
Underwriter Laboratories.
7. Power for devices connected through relay/control output wiring must be provided by a UL
Listed power limited power source.
8. RS485-type readers have not been investigated by Underwriters Laboratories.
9. Encrypted communication has not investigated by Underwriters Laboratories.
10. For a UL 294 Listed system the following Listed readers may be used.
Manufacturer Models
HID Global Corp. 30387, 31503, 31815, 31880, 32005, 32788, 32985, 5355, 5365,
5395, 5405, 5455, 6005, 6100, 3110-6445, R10T, R10N, R15N,
R15T, RP15N, RP15T, R40N, R40T, RK40N, RK40T, RP40N,
RP40T, RPK40N, RPK40T
All models may be followed by additional suffixes
OSDP Readers: R10Exxx, RP10Exxx, R15Exxx, RP15Exxx,
R30Exxx, RP30Exxx, R40Exxx, RP40Exxx, RK40Exxx,
RPK40Exxx.
All models may be followed by additional suffixes. The last “X” in
the model number maybe an “R” or “N”
Mercury Security Corp. MR-5, MR-20
11. The maximum Wiegand line impedance is 8 ohms, representing 22 AWG @ 500 feet.
12. The HID 3110-6445 shall be powered by a separate power source that is UL 294 or UL 603
power limited power source.
13. Suitable for use with the model P2K-nnn-UL-x Security Management System, where n can be
any number 0 through 9 and where x can be any three letters A through Z.
14. UL 294 Performance Levels
Destructive Attack Level I
Endurance Level IV
Line Security Level I
Standby Power Level I
CKM-MR51E Hardware Installation Manual
24-10707-58 Rev. E
1
CKM-MR51E READER TERMINAL MODULE
This document provides hardware installation and setup instructions for
CKM-MR51E, the authentic Mercury™ single reader, power over ethernet
(PoE) module. This document is divided into the following sections:
•General Information on page 1
•Mounting Information on page 2
•Wiring Information on page 4
•Setup Information on page 7
•IP Address Configuration on page 9
•Status LEDs on page 12
•Specifications on page 13
•Maintenance on page 14
GENERAL INFORMATION
The CKM-MR51E reader interface provides a network connected, single door
with paired reader, PoE based solution to the OEM integrator for interfacing
TTL, Wiegand, or RS-485 type readers to door hardware. The onboard twisted
pair Ethernet jack with PoE support enables easy installation.
NOTE: For UL installations, PoE powered devices shall not be used; power for
these devices must be provided by a UL 294 listed, power limited source
(12 VDC).
One physical barrier can be controlled with the CKM-MR51E, using single or
paired readers. The first reader port can accommodate a read head that utilizes
Wiegand, magnetic stripe, or two-wire RS-485 electrical signaling standards;
one- or two-wire LED controls; and buzzer control (one-wire LED mode only).
The second reader port can accommodate a read head that utilizes Wiegand or
magnetic stripe signaling; one- or two-wire LED controls; and buzzer control
(one-wire LED mode only). Two Form-C relay outputs may be used for door
strike control or alarm signaling. The relay contacts are rated at 5 A at
30 VAC/DC, dry contact configuration. Four inputs are provided for
monitoring the door contacts, exit push buttons, and alarm contacts. The
CKM-MR51E requires power from PoE or local 12 VDC. The CKM-MR51E
may be mounted in a three-gang switch box.
CKM-MR51E Hardware Installation Manual
24-10707-58 Rev. E
2
A mounting plate is supplied with the unit. The CKM-MR51E may be mounted
in an enclosure; the supplied mounting plate has mounting holes that match the
CKM-MR50 mounting footprint.
MOUNTING INFORMATION
Figure 1: CKM-MR51E Hardware
Figure 2: CKM-MR51E Hardware (Solder Side)
Additional Mounting Information
Optional mounting items are shown in Figure 3.
• Three-gang stainless steel blank cover: Leviton part number 84033-40.
Available from Graybar, part number 88158404
• Magnetic switch set: G.R.I. part number: 505
2
3
41
S1
S2
123456
ON
J3J7
K1
K2
12V
J5
PoE
J6
TB1 TB2 TB3 TB4 TB5 TB6
111111
IN1 IN2 IN3 IN4 VO LED BZR CLK DAT GND VO GNDDATCLKBZRLED GNDVIN NO NC2-CNONC1-C
J2
0.2 [5.08] 2.35 [59.69]
0.15 [3.81]
2.55 [64.77] 2.55 [64.77]
5.4 [137.16]
STATUS LEDs
2.75 [69.85]
DIP SWITCH
RESET SWITCH
PoE/12Vdc
POWER SELECTOR
JUMPER
ETHERNET RJ45
CONNECTOR
ACTIVITY
(YELLOW)
LINK
(GRREN)
123456
VO
VO IN2 IN1IN3IN4
LED
BZR
CLK
DAT
GND
LED
BZR
CLK
DAT
NC GNDGND
VIN
NO
RLY 1
NO
RLY 2
NC CC
TB6
TB5
TB4
TB3
TB2
TB1
J1
6V
5V
3.3V
LNK
ACT
(K1)
(K2)
J4
D24
D19
ETHERNET
STATUS
LEDs
RELAY K1
LED
RELAY K2
LED
STATUS LEDs
SOLDER SIDE
CKM-MR51E Hardware Installation Manual
24-10707-58 Rev. E
3
Figure 3: CKM-MR51E Mounting Side View
Figure 4 shows mounting plate dimensions.
Figure 4: CKM-MR51E Mounting Plate Dimensions
FIELD WIRING
MR51e WITH INCLUDED
MOUNTING PLATE
TO ETHERNET
NETWORK
OPTIONAL 3-GANG
JUNCTION BOX
OPTIONAL BLANK
COVER W/SCREWS
OPTIONAL MAGNETIC
TAMPER SWITCH
3.85 [97.8]
2.35 [59.7]
5.50 [139.7]
3.63 [92.1]
3.30 [83.8]
3.63 [92.1]
Ø0.16 [Ø4.0]
MR50 MGT HOLES
4PL
Ø0.16 [Ø4.0]
3-GANG MGT HOLES
4PL
CKM-MR51E Hardware Installation Manual
24-10707-58 Rev. E
4
WIRING INFORMATION
This sections covers the following:
•Cable Routing
•Input Power
•Communication Wiring
•Reader Wiring
•Input Circuit Wiring
•Relay Circuit Wiring
Cable Routing
The cables should run in grounded conduit or at least two feet from AC
power, fluorescent lights, or other high energy sources.
IMPORTANT: All data cables should be physically separated from power lines. If
conduit is used, do not run data cables in the same conduit as power cables or
certain door strike cables, e.g. strike voltage greater that 42V or Magnetic door
locks without EMI suppression.
All cables must conform with the following regulations:
• National Electrical Code
•NFPA 70
• Local electrical codes
• Canadian Electric Code C22.1 (installations in Canada)
• BSI Standard BS7671, latest edition (installations in Great Britain)
Cabling should be made using good wiring practices and should be long
enough to allow service loops at their terminations in the enclosure.
Input Power
The CKM-MR51E is powered by one of two ways (jumper selected):
• Power is supplied via the Ethernet connection using PoE, fully
compliant to IEEE 802.3af, or
• Local 12 VDC power supply, TB5-3 (VIN), TB5-4 (GND).
CKM-MR51E Hardware Installation Manual
24-10707-58 Rev. E
5
Communication Wiring
Communication between the EP controller and the CKM-MR51E is
Ethernet. (10Base-T/100Base-TX).
Reader Wiring
The first reader port supports Wiegand, magnetic stripe, and two-wire
RS-485 electrical interfaces. The second reader port supports Wiegand
and magnetic stripe electrical interfaces. Power to the first reader is
12 VDC and is current limited to 150 mA. The second reader may be
powered from the auxiliary power output on TB5-1 and TB5-2. Readers
that require different voltage or have high current requirements should be
powered separately. Refer to the reader manufacture specifications for
cabling requirements. In the two-wire LED mode, the Buzzer output is
used to drive the second LED. Reader port configuration is set via the
host software.
Figure 5: CKM-MR51E First Reader Wiring
Figure 6: CKM-MR51E Second Reader Wiring
IMPORTANT: When powering any remote device(s) by the CKM-MR51E, care
must be taken not to exceed the maximum current available. Cable gauge must
also be evaluated. See Specifications for details.
CKM-MR51E Hardware Installation Manual
24-10707-58 Rev. E
6
Input Circuit Wiring
Typically, these inputs are used to monitor door position, request to exit,
or alarm contacts. Input circuits can be configured as unsupervised or
supervised. When unsupervised, reporting consists of only the open or
closed states.
When request to exit (REX) input is supervised, the strike remains locked
when a transition to open state or short state occurs. Such transitions do
not generate notifications. The strike relay unlocks only when the REX
input changes to the active state, that is, when the REX switch contact
opens or closes depending on the configuration.
When configured as supervised, the input circuit reports not only open
and closed, but also open circuit, shorted, grounded, and foreign voltage.
A supervised input circuit requires two resistors be added to the circuit to
facilitate proper reporting. The standard supervised circuit requires 1K
Ohm, 1% resistors and should be located as close to the sensor as
possible. Custom end of line (EOL) resistances may be configured via the
host software.
NOTE: Grounded and foreign voltage states are not a requirement of UL 294
and therefore not verified by UL.
The input circuit wiring configurations shown in Figure 7 are supported,
but may not be typical.
Figure 7: CKM-MR51E Input Circuit Wiring
1K,1%
1K,1%
1K,1%
1K,1%
Standard Supervised Circuit,
Normally Closed Contact
Standard Supervised Circuit,
Normally Open Contact
Unsupervised Circuit,
Normally Open Contact
Unsupervised Circuit,
Normally Closed Contact
TB2
IN4
IN2
IN3
1
IN1
TB1
1
}
Indice
Altri manuali Johnson Controls Unità di controllo
Johnson Controls
Johnson Controls Mercury 3 Series Manuale
Johnson Controls
Johnson Controls Tyco DV-5a Series Manuale utente
Johnson Controls
Johnson Controls Tyco DV-5a Series Manuale utente
Johnson Controls
Johnson Controls CKM-F8P Manuale
Johnson Controls
Johnson Controls METASYS NU-XBN101-0 Manuale utente
Johnson Controls
Johnson Controls MS-IOM3723 Manuale utente
Johnson Controls
Johnson Controls PENN P470 Manuale
Johnson Controls
Johnson Controls IOM3711 Manuale utente
Johnson Controls
Johnson Controls System 450 Series Manuale utente
Johnson Controls
Johnson Controls VP101DBB Manuale utente
Johnson Controls
Johnson Controls PENN P70 Series Manuale
Johnson Controls
Johnson Controls IOM3731 Manuale utente
Johnson Controls
Johnson Controls TYCO DPV-1 Manuale di istruzioni
Johnson Controls
Johnson Controls A19 Series Manuale utente
Johnson Controls
Johnson Controls FX-PCX2721 Manuale utente
Johnson Controls
Johnson Controls MS-IOM2710-0U Manuale utente
Johnson Controls
Johnson Controls Tyco HSM3408 Manuale utente
Johnson Controls
Johnson Controls IOM1711 Manuale utente
Johnson Controls
Johnson Controls VG8000V Series Manuale utente
Johnson Controls
Johnson Controls S1-TTSCC Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
