Johnson 40-6625 Manuale utente

Self-Leveling Ultra-Bright Cross-Line Laser

Model No. 40-6625

Instruction Manual

Congratulations on your choice of this Self-Leveling Cross-Line Laser.

We suggest you read this instruction manual thoroughly before using

the instrument. Save this instruction manual for future use.

This is a Class IIIa laser tool and is manufactured to comply with

CFR 21, parts 1040 .10 and 1040 .11 as well as international safety

rule IEC 285.

8185H-All_Manuals 8/13/14 8:14 AM Page 1

Table of Contents

1. Kit Contents

2. Features and Functions

3. Safety Instructions

4. Location/Content

of Warning Labels

5. Location of Parts/Components

6. Operating Instructions

7. Using the Product

8. Self-Check & Fine Calibration

9. Technical Specifications

10. Application Demonstrations

11. Care and Handling

12. Product Warranty

13. Warranty Registration

14. Accessories

15. Trouble Shooting

1. Kit Contents

Description for Model 40-6625 Qty.

Self-Leveling Cross Line Laser 1

Multi-Functional Elevating Magnetic Base 1

“AA” Alkaline Batteries 3

Mounting Strap 1

Magnetic Target 1

Instruction Manual with Warranty Card 1

Soft Sided Pouch 1

2. Features and Functions

• Able to project one cross-line beam, consisting of one

horizontal line and one vertical line.

• Magnetic dampening compensation system.

• Laser flashes/sounds audible alarm when beyond leveling range.

• Manual mode feature allows unit to be tipped at extreme angles

without the audible alarm and laser flash being triggered

• Multi-functional elevating magnetic base is included to allow

hanging on wall, attach to metal, or connect to tripod

(5/8"-11 or 1/4"-20).

• While on the bracket, the laser can be raised or lowered 2-1/2"

and rotate 360º.

• Includes adjustable strap for attachment to pipe or conduit.

8185H-All_Manuals 8/13/14 8:14 AM Page 2

3. Safety Instructions

Please read and understand all of the following instructions, prior

to using this tool. Failure to do so, may void the warranty.

ATTENTION IM ORTANT

• Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

• Do not stare directly at the laser beam.

• Do not project the laser beam directly into the eyes of others.

• Do not set up laser tool at eye level or operate the tool near a reflective surface as

the laser beam could be projected into your eyes or into the eyes of others.

• Do not place the laser tool in a manner that may cause someone to unintentionally

look into the laser beam. Serious eye injury may result.

• Do not operate the tool in explosive environments, i.e. in the presence of gases or

flammable liquids.

• Keep the laser tool out of the reach of children and other untrained persons.

• Do not attempt to view the laser beam through optical tools such as telescopes as

serious eye injury may result.

• Always turn the laser tool off when not in use or left unattended for a period of time.

• Remove the batteries when storing the tool for an extended time (more than 3 months)

to avoid damage to the tool should the batteries deteriorate.

• Do not attempt to repair or disassemble the laser tool. If unqualified persons attempt

to repair this tool, warranty will be void.

• Use only original ohnson®parts and accessories purchased from your ohnson®

authorized dealer. Use of non- ohnson®parts and accessories will void warranty.

8185H-All_Manuals 8/13/14 8:14 AM Page 3

DANGER!

Class IIIa Laser Product

Max. Power Output: ≤5mW

Wavelength: 625-645nm

THIS TOOL EMITS LASER RADIATION.

DO NOT STARE INTO BEAM.

AVOID DIRECT EYE EX OSURE.

4. Location/Content of Warning Labels

8185H-All_Manuals 8/13/14 8:14 AM Page 4

5. Location of art/Components

Instrument Manual mode button

Power LED

On/Off Switch

Rubber Co-Molded

Housing

Laser Output

Window

Manual Mode LED

1/4" – 20 thread

5/8" thread Sound Port

Window Frame

Self-Calibrate

Screw/Plug

Battery

Cover

Side Self-Calibrate

Screw/Plug

Battery

Cover

Screw

8185H-All_Manuals 8/13/14 8:14 AM Page 5

Multi-Functional Elevating Magnetic Base

6. Operating Instructions

Battery Installation

Note: Always check to be sure that the on/off switch

is in the off position before removing and replacing

batteries.

1. Open the battery-box cover and put in three “AA”

batteries according to the illustrated polarity direction

2. Place the laser on a platform or a tripod.

3. Power on the laser by turning the on/off switch to

the on position, and a cross line will be projected.

Wall Screw

Hang Hole

Strap Slots 1/4" thread

1/4" thread

Laser

Attachment Wheel

5/8" thread

Locking Knob

Magnets

IM ORTANT: It is the responsibility of the user to verify the

calibration of the instrument before each use.

8185H-All_Manuals 8/13/14 8:14 AM Page 6

Note:

• Pay attention to the polarity of the batteries.

• Used (discharged) batteries are hazardous waste and should be

disposed of properly.

• If the power indicator light is flashing, the batteries are low and

should be changed soon.

7. Using the Product

This base was specially designed for more extensive adaptability of

the laser. Both the laser and the base can be connected with a

standard tripod by 5/8"-11 thread and camera tripod by

1/4" – 20 thread. With the use of its base, the laser can be freely

rotated, elevated 2-1/2", hung on the wall, attached to a metal plate,

or connected on pipe with use of its strap.

1. As shown in fig. 1, take out the magnetic base.

2. As shown in fig. 2, install the laser on the base (1/4" – 20

thread) by rotating the connecting knob counter-clockwise.

Figure 2Figure 1

8185H-All_Manuals 8/13/14 8:14 AM Page 7

Manual Mode Operating Instructions

1. Locate the Manual Mode Button (fig. 3) on the side

of the laser, above the on/off switch.

2. When the laser is turned on,

push the button once to

engage the Manual Mode

Feature. Red light next to

manual mode button will

turn on and green power

LED will stay on.

3. Push the button a second

time to turn off the Manual

Mode Feature. Red light will

turn off and green power

LED will stay on.

Note:

When the Manual Mode Feature

is engaged, the self-leveling

alarm is deactivated.

Figure 3

8185H-All_Manuals 8/13/14 8:14 AM Page 8

8. Self-Check & Fine Calibration

IM ORTANT: It is the responsibility of the user to verify the

calibration of the instrument before each use.

1. Set the laser on a level flat head tripod centered between two

walls (marked 1 & 2) approximately 15 feet apart. (See fig. 1).

2. Point the laser directly at wall 1. Turn the laser on and mark

the intersection of the beams as point A.

3. Turn the laser 180 degrees so that the laser is pointed directly

at wall 2. Turn the laser and mark the intersection of the

beams as point B.

4. Move the laser and the tripod so the laser is positioned

approximately 2 feet away from wall 1 (see fig. 2). Level the

tripod and position the laser on the tripod facing wall 1. Turn the

laser on and mark the intersection of the beams as point C.

5. Turn the laser off and rotate the laser 180 degrees so that it is

facing directly to wall 2.

6. Turn on the laser and mark the

intersection of the beams as point D.

7. Measure the distance between

points A & C.

8. Measure the distance between

points B & D.

9. If the difference between points

A & C and points B & D are less

than 1/16", your laser is within

its tolerance.

Wall 1 Wall 2

Fig 1

Fig 2

8185H-All_Manuals 8/13/14 8:14 AM Page 9

Calibration

Re-calibration can be performed as described below.

1. Use a level to mark a horizontal reference line on the wall.

2. Power on the unit to compare the projected horizontal line with

its references. Compensator has to be locked before

making calibration adjustments. If it tilts, remove the side

plastic screw/plug and use an allen wrench to calibrate the

unit through its side calibration hole. Rotate the allen

wrench clockwise when the horizontal line tilts right. Rotate

the allen wrench counter-clockwise when the horizontal line

tilts to the left.

3. If the horizontal line is too low or too high, carefully

disassemble the window frame by removing the outer plastic

screw/plug and the inner metal screw. Use an allen wrench

to calibrate the adjustment screws located between the

glass prisms. Rotate the allen wrench clockwise when the

horizontal line is too low. Rotate the allen wrench counter-

clockwise when the horizontal line is too high. Reassemble

the window frame after completing the calibration.

8185H-All_Manuals 8/13/14 8:14 AM Page 10

Indice

Lingue:

Altri manuali Johnson Strumento di misura

Johnson

Johnson 1888-1900 Manuale utente

Johnson

Johnson 40-6515 Manuale utente

Johnson

Johnson LEVEL UP 40-6535 Manuale utente

Johnson

Johnson 40-6502 Manuale utente

Johnson

Johnson 1886-0000 Manuale utente

Johnson

Johnson 40-6688 Manuale utente

Johnson

Johnson JLX 40-6590 Manuale utente

Johnson

Johnson 40-6557 Manuale utente

Johnson

Johnson 40-6705 Manuale utente

Johnson

Johnson 40-6676 Manuale utente

Johnson

Johnson Old Town Sportsman iPilot Manuale utente

Johnson

Johnson 1888-1100 Manuale utente

Johnson

Johnson 1888-0700 Manuale utente

Johnson

Johnson LDM195 Manuale utente

Johnson

Johnson 40-6543 Manuale utente

Johnson

Johnson 40-6690 Manuale utente

Johnson

Johnson 40-6624 Manuale utente

Johnson

Johnson 40-6064 Manuale utente

Johnson

Johnson 40-6535 Manuale utente

Johnson

Johnson 40-6618 Manuale utente

Johnson

Johnson 1454-0000 Manuale utente

Johnson

Johnson LDM150 Manuale utente

Johnson

Johnson 40-6700 Manuale utente

Johnson

Johnson 40-6932 Istruzioni operative e di manutenzione

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente