Konica Minolta PI-506 Manuale utente

E-1

INSTALLATION MANUAL

A10Y955000

PI-506 Post Inserter

I. Accessory parts

II. Preliminary preparations

When installing the PI-506 to the Finisher, install the

PI-506 first then install the Finisher to the main body.

Note:

When handling the PI-506, grip it as shown in the

illustration below.

III. Installation Procedures

1. Remove the top cover from the Finisher.

(1) Remove the two screw covers at the rear side

of the top cover, then remove the screws.

(2) Open the front door and remove the 3 screws.

(3) Remove the top cover.

No. Name Shape Q’ty

1. PI-506

15JFIXC001SA

2. Wire bundle

cover /1

15JFIXC002SA

3. Screw cover

15JFIXC003SA

4. Positioning

screw 2

5. TP screw

M4x6 3

6. Truss screw

M4x6 (black) 1

7. Installation

manual

Note:

Lifting the machine in an awkward position or

transporting it in a poorly balanced position could

result in personal injury. When transporting the

machine, be sure to take a good position of not

being excessively loaded. (mass: approx. 10.5kg)

15JFIXC004SA

Screw covers

15JFIXE005SA

15JFIXC006SA

15JFIXE007SA

Top cover

Applied Machines: FS-528/FS-611

E-2

2. Reinstall the screws removed in step 1-(1).

3. Install the 2 positioning screws at the rear side of

the Finisher.

4. Install the PI-506.

(1) Install the PI-506 on top of the Finisher.

Note:

• To lock the PI-506 in place, first align its key-

hole slots so that the positioning screws you

installed on the Finisher feed through the wide

parts of the slots.

• Then slide the PI-506 so that the heads of the

positioning screws are locked over the narrow

parts of the keyhole slots.

Check that there is no gap between the PI-506

and the Finisher in the rear side exterior panel.

If there is the gap, install the PI-506 again.

(2) Remove the packing tape and protective mate-

rials.

(3) Connect the PI-506 connector to the connector

at the top front of the Finisher.

15JFIXC008SA

15JFIXE009SA

Positioning screws

15JFIXE010SA

Positioning screw

A10YIXC001CA

PI-506 connector

Finisher connector

E-3

(4) Secure the PI-506. (TP screws M4x6: 3 pcs.)

5. Install the wire bundle cover /1 to the PI-506

connector. (Truss screw M4x6 (black): 1 pc.)

6. Install the screw cover on the top front of the Fin-

isher.

7. Install the Finisher on the main body (refer to the

Finisher Installation manual).

8. Plug in the power cord and turn the Main power

switch ON of the main body.

9. Adjusting the spread of the paper-width guide

15JFIXE011SA

Connector

TP screws M4x6

A10YIXC002CA

Front

TP screws M4x6

15JFIXE014SB

Truss screw

M4x6 (black)

Wire bundle cover/1

Screw cover

Step

1. Enter [Service mode].

Note:

Refer to procedures in the Service Manual

to enter into the Serivce Mode.

2. Touch the “Finisher Adjustment” key.

3. Touch the “Cover Sheet Size Adj.” key to

indicate the [Cover sheet tray size adj.

(upper tray)] screen.

4. Set A4S or 8.5/11S paper in the upper

cover-sheet tray.

5. Touch the “Start” key.

6. When adjustment is completed, “Complete”

appears on the message display.

7. Touch the “Next” key to indicate the [Cover

Sheet Tray Size Adj. (Lower Tray)] screen.

8. Set A4S or 8.5/11S paper in the lower cover-

sheet tray.

9. Touch the “Start” key.

10. When adjustment is completed, “Complete”

appears on the message display.

11. Verify that each paper size can be properly

detected.

Altri manuali Konica Minolta Accessori per stampanti

Konica Minolta

Konica Minolta IT-101 Come usare

Konica Minolta

Konica Minolta DF-633 Manuale utente

Konica Minolta

Konica Minolta Image Controller IC-205 Manuale utente

Konica Minolta

Konica Minolta AFR-12 Guida alla configurazione

Konica Minolta

Konica Minolta HT-509 Manuale utente

Konica Minolta

Konica Minolta WT-513 Manuale utente

Konica Minolta

Konica Minolta Di1611 Manuale utente

Konica Minolta

Konica Minolta AD-509 Manuale utente

Konica Minolta

Konica Minolta FS-503 Manuale utente

Konica Minolta

Konica Minolta Magicolor 5550 Istruzioni operative e di manutenzione

Konica Minolta

Konica Minolta HT-502 Manuale utente

Konica Minolta

Konica Minolta LU-302 Manuale utente

Konica Minolta

Konica Minolta bizhub 361 Manuale utente

Konica Minolta

Konica Minolta LU-204 Manuale utente

Konica Minolta

Konica Minolta PC-410 Manuale utente

Konica Minolta

Konica Minolta bizhub 223 Manuale utente

Konica Minolta

Konica Minolta EK-608 Manuale utente

Konica Minolta

Konica Minolta FS-532 Manuale utente

Konica Minolta

Konica Minolta PC-101 Manuale utente

Konica Minolta

Konica Minolta Color Care IQ-501 Manuale utente

Konica Minolta

Konica Minolta FS-110 Manuale utente

Konica Minolta

Konica Minolta PK-517 Manuale utente

Konica Minolta

Konica Minolta HD-524 Manuale utente

Konica Minolta

Konica Minolta JS-506 Manuale utente

Manuali Accessori per stampanti popolari di altre marche

Star Micronics

Star Micronics TSP800 Series Manuale utente

REA

REA JET HR pro 2K Manuale utente

HP Laserjet,Color Laserjet 4si Manuale utente

oliser

oliser MS 45 Manuale utente

Roland

Roland DU2-64 Istruzioni e ricette

Xerox

Xerox EFI EXP6000 Manuale utente

Canon

Canon Finisher-T1 Manuale utente

Sharp

Sharp FO-1MK Manuale utente

Labelmate

Labelmate PM-300 Manuale utente

Epson

Epson T6248 Manuale operativo

Epson

Epson OT-BZ20 Manuale utente

Canon

Canon TonerRobot EP-27 Manuale utente

Ricoh

Ricoh LCIT RT5100 Guida rapida

GBC

GBC 16 Series Manuale utente

Canon

Canon INNER 2-WAY TRAY-E1 Manuale operativo e di manutenzione

Develop

Develop SD-509 Manuale utente

Kyocera

Kyocera KM-6230 Manuale

Triumph Adler

Triumph Adler DF-710 Manuale