KPS DMM3000 Manuale utente
User Manual / MANUAL DEL USUARIO /
Manuel d'utilisation /
Benutzerhandbuch / Manuale Utente
DMM3000
LIMITED
WARRANTY
YEARS
IT
EN All New True RMS Multimeter
Multímetro de valor eficaz verdadero totalmente rediseñado
Multimètre RMS (« valeurs efficaces vraies ») avec tout
nouveau design
Ganz neu gestaltetes True RMS Vielfachmessgerät
Multimetro a vero valore efficace di progettazione
assolutamente nuova
EN
DMM3000
Safety Information
!
Read First
!
Understand and follow operating instructions carefully.
WARNING
!
Identifies hazardous conditions and actions that could cause
BODILY HARM or DEATH.
WARNING
!
•When using test leads or probes, keep your fingers behind the
finger guards.
•Remove test lead from Meter before opening the battery door or
meter case.
•Use the Meter only as specified in this manual or the protection
by the Meter might be impaired.
•Always use proper terminals, switch position, and range for
measurements.
•Verify the Meter’s operation by measuring a known voltage.
If in doubt, have the Meter serviced.
•Do not apply more than the rated voltage, as marked on Meter,
between terminals or between any terminal and earth ground.
•Only replace the blown fuse with the proper rating as specified
in this manual.
•Use caution with voltages above 30 Vac rms, 42 Vac peak,or 60
Vdc. These voltages pose a shock hazard.
•To avoid false readings that can lead to electric shock and
injury, replace battery as soon as low battery indicator.
•Disconnect circuit power and discharge all high-voltage
capaci-tors before testing resistance, continuity, diodes, or
capacitance.
•Do not use Meter around explosive gas or vapor.
•To reduce the risk of fire or electric shock do not expose this
product to rain or moisture.
CAUTION
!
Identifies conditions and actions that could DAMAGE the meter or
equipment under test.
1
EN
DMM3000
CAUTION
!
•Disconnect the test leads from the test points before changing
the position of the function rotary switch.
•
Do not expose Meter to extremes in temperature or high humidity.
•1HYHUVHWWKHPHWHULQȍ$IXQFWLRQWRPHDVXUHWKH
voltage of a power supply circuit in equipment that could result
in damage the meter and the equipment under test.
Symbols as marked on the meter and
Instruction manual
~
Risk of electric shock
See instruction manual
DC measurement
Equipment protected by double or reinforced insulation
Battery
Fuse
Earth
AC measurement
Conforms to EU directives
Do not discard this product or throw away
Attention! Magnets might affect the correct functioning
of cardiac pacemakers and implanted defibrillators.
As a user of such medical devices, keep a sufficient
distance to the magnet.
!
To alert you to the presence of a potentially hazardous voltage,
when the Tester detects a voltage ≧30 V or a voltage overload
(OL) in V, mV, AutoV . The symbol is displayed.
Unsafe Voltage
Do not attempt to repair this Meter.
It contains no user-serviceable parts. Repair or servicing should
only be performed by qualified personnel.
Maintenance
Periodically wipe the case with a dry cloth and detergent.
Do not use abrasives or solvents.
Cleaning
2
EN
DMM3000
1VoltSeek Light
2LCD Display
3Button
4Rotary Switch
6Common lnput
7A lnput
5V , , , lnput(or ”+”)
The Meter Description
Front Panel Illustration
1. VoltSeek Light
2. 6,000 counts digital and 60 segments analog display
3. Push-buttons.
4. Rotary switch for turn the Power On / Off and select the
function.
5. Input Terminal for Multi-function.
6. Input Terminal for A.
7. Common (Ground reference) Input Terminal.
Introduction
3
EN
DMM3000
•6,000 count digital and 60 segments analog display
•Large white LED backlight display
•True RMS measurements on ACV
•LoZ for prevent false reading from ghost voltage
•AutoVolt automatic AC/DC voltage selection
•Auto Ranging
•0.5% DCV accuracy
•Smart Hold
•Peak Hold for capture peak readings
•Relative Function
•Auto Power Off (can be disabled)
•Capacitance measurements
•Frequency Counter on ACV
•Diode Test
•Frequency Counter on ACA
•10Amp ACA/DCA
•11A/1000V High Energy Fuse
•VoltSeekTM for non-contact voltage detection
•EasyStickTM holster with built in magnetic sticker
•ContiVisionTM for visible continuity beeper
•Battery Capacity indication in segments
•Included Holster with Probe Holder, Tilt Stand and Magnetic
sticker
•CAT IV 600V/ CATIII 1000V standard
Features :
Making Basic Measurements
Preparation and Caution Before Measurement
Observe the rules of Warnings and Cautions.
! !!
CAUTION
!
When connecting the test leads to the DUT (Device Under Test)
connect the common test leads before connecting the live test
leads ; when removing the test leads, remove the live test leads
before removing the common test leads.
4
EN
DMM3000
Measuring ACV/DCV/AutoV Voltage
Dial the switch to select the measuring function.
Disconnect
Measuring AC/DC Current
Dial the switch to select the measuring function.
5
EN
DMM3000
Measuring Capacitance / Diode
Dial the switch and press the Function button to select the
measuring function
Measuring Continuity / Resistance
Red Black
Dial the switch and press the Function button to select the
measuring function.
6
EN
DMM3000
WARNING
!
The VoltSeek LED indicates the electric field. If the VoltSeek LED
is not on, voltage could still be present.
VoltSeek
Dial the switch and press the RANGE button to select the
measuring function and sensitivity.
Switch
Position Function
Using the Function
Press the Function button to change the function on the same
switch position.
7
EN
DMM3000
Press Ragen Button >2 Sec to Auto Mode
1
123
Range Button
Press
Leave the peak hold mode
Button > 2 sec
Peak Hold (for AC only)
In the Peak Hold function ,the meter records the peak min. value
and the peak max. value when the inputs goes below the recorded
peak min. value or above the recorded peak max. value ,the meter
records the new value . Press Hold button to pause the recording.
8
EN
DMM3000
Smart Hold
The meter will beep continuously and the display will flash if the
measured signal is larger than the display reading by 50 counts.
(However ,it can not detect across the AC and DC Voltage /
Current).
5HODWLYHǻ
Press the Relative button to enable/disenable this function.
Backlight
Press the Backlight button to turn the backlight on/off.
9
Indice
Altri manuali KPS Strumento di misura
KPS
KPS KPS-CF100 Manuale utente
KPS
KPS KPS-PA440 Manuale utente
KPS
KPS DCM4010FLEX Manuale utente
KPS
KPS KPS-CC600 Manuale utente
KPS
KPS KPS-PA20 MINI Manuale utente
KPS
KPS KPS-AN10 Manuale utente
KPS
KPS KPS-PA70 Manuale utente
KPS
KPS DCM3018FLEX Manuale utente
KPS
KPS KPS-MT30 Manuale utente
KPS
KPS KPS-PF50 Manuale utente
KPS
KPS KPS-PF10 Manuale utente
KPS
KPS DCM3000 Manuale utente
KPS
KPS KPS-SN10 Manuale utente
KPS
KPS DCM4000T Manuale utente
KPS
KPS DCM3010FLEX Manuale utente
KPS
KPS MS2030 Manuale utente
KPS
KPS DCM8500PV Manuale utente
KPS
KPS DCM7000BT Manuale utente
KPS
KPS KPS-PA50 MINI Manuale utente
KPS
KPS DCM3000 Manuale utente
