LaserLiner ZipLevel Plus 30 Manuale utente

Operation manual

ZipLevel Plus 30

02_Man_ZipLevel_GB-1012.indd 1 15.02.13 07:32

02_Man_ZipLevel_GB-1012.indd 02 15.02.13 07:32

ZipLevel Plus 30

Professional precision altimeter

The ZipLevel is a professional altimeter which enables you to scale and level

on your own also around corners with accuracy within 2 mm. You have a

working area up to ± 6 m vertical and up to 60 m in diameter. The digital

measuring module shows all your measurements and is easy to operate.

The extremely sturdy measurement cable with patented gas-liquid-system

reliably works from -30 °C up to +70 °C.

Read the operating instructions and the enclosed brochure „Guaran-

tee and additional notices“ completely. Follow the instructions they

contain. Safely keep these documents for future reference.

ACable reel

BSecuring points

CMeasurement line

DMeasuring module

EBattery compartment

(back)

FRoom for measuring

module

GPocket for operation

manual

HProtective cap

Backside:

IFeeler rod

02_Man_ZipLevel_GB-1012.indd 03 15.02.13 07:32

Inserting batteries into the measuring module

Open the battery compartment (E)

and insert the batteries according to

the installation symbol. Pay attention

to the correct polarity. Close the

battery compartment again.

Console

The keys HOLD and ON/OFF react

instantaneously, all the other keys have

to be pressed for 2 seconds in order

to activate or deactivate the particular

function. The functions are also fitted

with audible signals (clicking and blee-

ping) which makes it easier to work

overhead or in non visible areas.

The ZipLevel memorizes the last accomplished function. When you

turn the instrument on again and intend to leave the function,

press the accordant key for 2 seconds.

Hold the Function

keys for 2 seconds!

–

02_Man_ZipLevel_GB-1012.indd 04 15.02.13 07:32

ZipLevel Plus 30

Quick start of the ZipLevel

Open the bottom protective cap of the basic unit and remove the

measuring module. Lay the basic unit on the floor with the back facing

down. Slowly pull a sufficient length of line off the cable reel. The altitude

will be transferred from the basic unit to the measuring module.

Switch the measuring module on with the ON/OFF-key and put the unit

with its back or base on the required place of reference. When the display

is ready, you will hear 2 short audible bleeps. Press the ZERO-key for

2 seconds. Keep the measuring module steady until the figure zero

appears on the display. The appliance has now been set.

Back facing

down!

Base

Back

If the basic unit gets moved, the measuring module needs to be

set at the place of reference again.

02_Man_ZipLevel_GB-1012.indd 05 15.02.13 07:32

Quick start of the ZipLevel

Give a place of reference to the measuring module (press ZERO-key) and

move it to a different height. The appliance shows the difference in height

between the place of reference and the measuring point. Now you can

hold the appliance against any point and it always shows you the current

height towards the place of reference.

Always use the measuring module with the side, which was used to set

ZERO. Do not change from one locating side to another without setting

to ZERO again.

If you want to find out the height between floor and ceiling set the

appliance to ZERO with its back or bottom side on the floor. Then hold

the top, base or back to the ceiling in order to measure. Manually add

the height (8,8 cm) or thickness (5,0 cm) of the measuring module to

the shown data.

Make sure that the device is set to „boot off“. For more information,

see chapter „Boot on“ / „Boot off“ (page 13).

reference point

measuring point

02_Man_ZipLevel_GB-1012.indd 06 15.02.13 07:32

ZipLevel Plus 30

Keys and functions

ON/OFF

With this key you switch the unit on and off. If no key has been pressed or

the measuring module has not been moved within 4 minutes, the unit will

switch itself off automatically. After 3 minutes without any activity the unit

will sound a warning by giving 2 long bleeps.

HOLD

The HOLD-function is used where you have problems reading the display

or where you intend to keep the measured data. The function can be

switched on and off by shortly pressing the HOLD-key.

Measuring and keeping of the data (see drawing page 8):

1) First you set the unit at the required point with the ZERO-key.

2) Shortly press the HOLD-key as long as the measuring module is still

being moved. The unit will then give a series of bleeps.

3) Move the measuring module to the place where you intend to measure.

4) Wait until the unit has stabilized and therefore no more bleeps are

audible.

5) Retrieve the measuring module. The data of the remote point will be

kept on the display. Shortly press HOLD again to leave this function.

02_Man_ZipLevel_GB-1012.indd 07 15.02.13 07:32

Examples for the HOLD-function:

ZERO

Press the ZERO-key for 2 seconds in order to make the present height

(location of the measuring module) the point of reference. The unit must

not be moved in this process!

3 m

Level of reference

New level of reference

1. ZERO2. Press HOLD

When set zo zero

at the top

-3 m will be shown

at the bottom

02_Man_ZipLevel_GB-1012.indd 08 15.02.13 07:32

ZipLevel Plus 30

SCALE

With this you choose the required measurements in millimetres, centime-

tres or meters. Press the SCALE-key for 2 seconds and hold. Now the

gauges the bottom right of the display will change. Release the key once

the required measurement appears. The measurement for millimetres is not

indicated, cm and m appear on the display. The unit „M“ is not available

in HighPrecision mode.

RES

The ZipLevel is featured with a choice of 3 display accuracies. Press the

RES-key for 2 seconds and keep it pressed in order to choose the required

resolution. Release the RES-key once the required resolution is shown.

Your choice is stored now up to next accuracy change.

0.2 cm: for highest accuracy

needs more time to stabilize 0.5 cm: for medium accuracy

needs less time for stabilization 1 cm: for rough measuring

quick stabilizing of the results

02_Man_ZipLevel_GB-1012.indd 09 15.02.13 07:32

RES HighPrecision mode

For particularly demanding measurements, the accuracy can be switched

from ± 2 mm to ± 0.2 mm. To do so, keep the RES button pressed and

press the ON/OFF button at the same time. Repeat the process to leave

HighPrecision mode.

0,02 cm 0,05 cm 0,1 cm

HighPrecision-Mode active

Measured from the starting position of the base unit,

the HighPrecision-Mode can be used in a working range

of ± 0.5 m.

02_Man_ZipLevel_GB-1012.indd 10 15.02.13 07:32

Indice

Altri manuali LaserLiner Strumento di misura

LaserLiner

LaserLiner SensoLite 100 Manuale utente

LaserLiner

LaserLiner Quadrum OneTouch Green Manuale utente

LaserLiner

LaserLiner CondenseSpot Manuale utente

LaserLiner

LaserLiner PowerCross-Laser 8 S Manuale utente

LaserLiner

LaserLiner X1-Laser Manuale utente

LaserLiner

LaserLiner MultiWet-Master Compact Plus Manuale utente

LaserLiner

LaserLiner 4K5 RA 500 Manuale utente

LaserLiner

LaserLiner PowerCross-Laser 5 Combi Manuale utente

LaserLiner

LaserLiner EasyCross-Laser Green Manuale utente

LaserLiner

LaserLiner DistanceCheck Manuale utente

LaserLiner

LaserLiner ClampMeter XP Manuale utente

LaserLiner

LaserLiner ThermoSpot Manuale utente

LaserLiner

LaserLiner RollPilot S12 Manuale utente

LaserLiner

LaserLiner RollPilot D12 Manuale utente

LaserLiner

LaserLiner EvolutionCross-Laser 8P PowerBright Manuale utente

LaserLiner

LaserLiner DistanceMaster Vision Manuale utente

LaserLiner

LaserLiner HandyLaser Manuale utente

LaserLiner

LaserLiner LaserRange-Master T7 Manuale utente

LaserLiner

LaserLiner SensoPilot Pro Manuale utente

LaserLiner

LaserLiner RollPilot Mini Manuale utente

LaserLiner

LaserLiner MoistureMaster Compact Plus Manuale utente

LaserLiner

LaserLiner DampFinder Compact Plus Manuale utente

LaserLiner

LaserLiner ACL 4C Manuale utente

LaserLiner

LaserLiner MasterLevel Box Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente