Linn HELIX Manuale utente
LINN HELIX
OWNERS MANUAL
2
INTRODUCTION Thank you for choosing our Linn HELIX LS150 Loudspeakers, the result of
extensive design and development work. The HELIX set new standards of performance in
loudspeakers of this type.
Remember, no loudspeaker is capable of improving the quality of the input signal so the HELIX should
be used with good quality ancillary equipment.
INSTALLATION Before unpacking the speakers, please remove all staples from the carton to avoid
possible damage to the cabinets.
When removing the loudspeakers from their boxes, lift the cabinets out by their sides. This will avoid
possible damage to the grilles and their drive units.
Please retain all packing for possible future transportation.
All loudspeakers perform best when rigidly mounted. To achieve this, Linn have designed a stand for
the HELIX, which includes stabilising floor spikes. These stands give optimum sound quality and ensure
that the drive units are correctly positioned for the listener.
I
STANDS
3
Connection of the loudspeakers to the amplifier should be made with a good quality cable. Linn K20
loudspeaker cable is ideal, the leads should be terminated with the connectors supplied to ensure
optimum performance. The use of other connectors will degrade the sound quality of your system.
The cable is marked with the Linn symbol to indicate directionality. The bare wires shown should be
connected to the amplifier and the end marked with the circular logo should he connected to the
loudspeakers.
< LOUDSPEAKERS AMPLIFIER >
Take care to ensure that the wiring is correct. The red socket is positive and the black is negative. The
positive wire (red connector) is identified by a rib along the side of the cable.
HELIX speakers are designed to perform best when placed close to a wall. Ideally the rear of the
loudspeaker should be between 4" and 12" (10 and 30cm) from the wall and at least 18" (45cm) from any
corner.
HELIX can also benefit from being angled inward slightly by 5 to 10 degrees.
These are general guidelines and a little experimentation with positioning will optimise results for a
particular room, your dealer will be pleased to do this when he installs your equipment.
CONNECTIONS
POSITIONING
4
The HELIX grille is special because it mounts directly onto the front facia of the speaker. This avoids the
problems of diffraction produced by conventional grille frames.
To remove the grille cloth, hold the facia with both hands behind the groove in the middle of the vertical
sides and pull forward until it is free from the wooden baffle behind.
To detach the grille cloth, gently pull its elastic edge over one corner of the facia and then slowly and
carefully detach the rest.
To re-assemble, reverse the process and re-attach the moulded facia to the speaker by lining up and
locating the lugs to their inserts on the wooden battle and push home firmly until the facia is flush with the
tweeter.
If the separate, smaller section of the facia shifts during this operation, it should be firmly pushed back
home. To re-fit the grille cloth, reverse the above procedure.
GRILLE
5
Bi-wiring improves the performance of a loudspeaker. By using a separate cable for the bass and treble
section some interaction between the bass and treble section is removed. The extra cost of an additional
pair of loudspeaker cables is more than justified by the improvement in sound quality gained.
To convert the HELIX to bi-wired mode, use the key provided to unscrew the negative (black) socket
caps and remove the link. Replace and tighten the caps and then repeat for the positive (red) sockets
and firmly re-tighten.
Because most amplifiers have only one speaker output you will have to double up the connection to the
speaker plug - your dealer will be pleased to make up the necessary leads for you, and to set up your
loudspeakers.
For ultimate performance you can go one step beyond bi-wiring and use two amplifiers, one channel for
the bass and one channel for the treble. Your dealer will be pleased to effect this mode of operation for
you.
BI-WIRING
BI-AMPING
6
Linn loudspeakers require no internal maintenance and on no account should you try to remove any of
the drive units, which are carefully tightened and sealed at the factory.
For servicing, always return the speakers as a pair to your supplier, using the original packing in order to
reduce the risk of damage in transit, If you have lost the packaging, your supplier can provide a
replacement set.
Ensure your equipment is insured by youduring transit, repair, and return shipping.
These units are guaranteed under the conditions that apply in the country of purchase. To help us,
please return your guarantee card.
In Addition to any statutory rights you have as a customer, we undertake to replace any parts that have
failed due to faulty manufacture if you register your purchase with us.
Please keep a copy of your sales receipt as this will establish the purchase date of the loudspeakers
and refer all enquiries through authorised dealers only.
LINN PRODUCTS LIMITED, FLOORS ROAD, WATERFOOT, EAGLESHAM,
GLASGOW G76 0EP, SCOTLAND. TELEPHONE: ++44 (0)141 307 7777
FACSIMILE: ++44 (0)141 644 4262.
MAINTENANCE/SERVICE
GUARANTEE
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Linn Altoparlanti
Linn
Linn Melodik Manuale utente
Linn
Linn KAN Manuale utente
Linn
Linn AKUBARIK Manuale utente
Linn
Linn KEILIDH Manuale utente
Linn
Linn Majik 140 Manuale utente
Linn
Linn EKWAL Manuale utente
Linn
Linn KAN II Manuale utente
Linn
Linn Komri Manuale utente
Linn
Linn NEXUS Manuale utente
Linn
Linn Majik 140 Manuale utente
Linn
Linn SEKRIT Manuale utente
Linn
Linn ESPEK Manuale utente
Linn
Linn LOUDSPEAKERS Manuale utente
Linn
Linn Majik 109 Manuale utente
Linn
Linn Majik 109 Manuale utente
Linn
Linn TRIKAN Manuale utente
Linn
Linn NINKA Manuale utente
Linn
Linn CUSTOM 2K 104C-S Manuale utente
Linn
Linn KABER LS500 Manuale utente
Linn
Linn LOUDSPEAKERS Manuale utente
