Lippert Components Jack-It Manuale utente

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Introduction

The Jack-IT® is a bicycle rack designed to attach to your RV.

Additional information about this product can be obtained from

www.lci1.com/support or by downloading the free myLCI app.

The app is available on iTunes® for iPhone® and iPad® and

also on Google Play™ for Android™ users.

iTunes®, iPhone®, and iPad® are registered trademarks of

Apple Inc. Google Play™ and Android™ are trademarks of

Google Inc

Lippert Components, Inc. recommends that the following

inspections, troubleshooting, component replacement, and

verications be completed only by certied RV technicians.

Safety Requirements

Moving parts can pinch,

crush or cut. Keep clear

and use caution.

Failure to follow the

instructions provided in

this manual may result

in death, serious injury,

vehicle damage, or

voiding of the component

warranty.

Jack-It

Aftermarket

Manual

Table Of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Tools required 2

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2

Securing Bikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Patent protected, trademarked, and produced by Let’s Go Aero, Inc

Corporate Ofce: 4474 Barnes Road, Colorado Springs, CO 80917 USA.

Made in China.

US Patent Numbers: 8,899,456, D717,716, D717,717, D684,917, D722,289,

patents pending.

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Preparation

Tools required

9/16” Socket Wrench

3/4” Socket Wrench

Installation Instructions

1. Remove the tongue jack from the coupler. Position the

PowerTower ™ (Fig. 1G) on the coupler. Place the jack on

the PowerTower™ (Fig. 1G) and secure both to the coupler

using 3 nuts, bolts and washers each (Fig. 1H, 1I, 1J).

Note: If there is no tongue jack, attach the PowerTower™ (Fig.

1G) to the coupler on the front of the trailer using 3 nuts,

bolts and washers each (Fig. 1H, 1I, 1J).

2. Attach the stinger (Fig. 1F) to the PowerTower™ (Fig. 1G)

using NoMotion™ pin and washers (Fig. 1C, 1D, 1A). For

safety, insert cotter pin (Fig. 1B) through the hole at the end

of the NoMotion™ pin (Fig. 1C) after tightening securely.

3. Attach base (Fig. 1E) to stinger (Fig. 1F) using NoMotion™

pin and washers (Fig. 1C, 1D, 1A). For safety, insert cotter

pin (Fig.1B) through the hole at the end of the NoMotion™

pin (Fig. 1C) after tightening securely.

Fig.1

The use of this product

while bicycles are loaded

may affect the turning

radius on some vehicles.

Check the turning radius

before travel.

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Fig.2

C D E

Securing Bikes

1. For two bicycles, the best technique is to postion the bicycles

front to back / back to front with the chain ring to the outside.

2. Hang one bicycle on the tow vehicle side of the bicycle rack,

so the top of the wheels are each supported by a cradle.

3. Secure by tensioning each rubber strap over the top of each

tire and engaging a strap hole with the end of the cradle.

4. Use the SwayStop™ pin to secure one wheel below the

frame where the wheel crosses the wing using the same

technique with the rubber strap (Fig. 3).

5. Repeat for a second bicycle on the trailer side of the bicycle

rack.

Note: Several hole positions are provided

for cradles (Fig. 2A). Pads (Fig. 2D) and

SwayStop™ pins (Fig. 2F) slide along the

length of wings (Fig. 2G).

4. If not already in place, slide two pads (Fig. 2D)

onto each wing (Fig. 2G).

5. Slide one SwayStop™ pin (Fig. 2F) onto each

wing (Fig. 2G). Attach wings (Fig. 2G) to base

(Fig. 2E) using two snap pins (Fig. 2H).

Note: SwayStop™ pins (Fig. 2F) should point in

opposite directions.

6. Install six rubber straps (Fig. 2B) one onto each

cradle (Fig. 2A) and one onto each SwayStop™

pin (Fig. 2F).

7. Attach four cradles (Fig. 2A). Attach two to each

wing (Fig. 2G) securing with cotter pins (Fig.

2C). Attach one on each wing facing the tow

vehicle and one on each wing facing the trailer.

Note: Adjustment will be necessary depending on

the size and desired position of the bicycles.

Always make sure all connections between the bicycle rack and the trailer

coupler are secure / tight / ready for travel. Always make sure the bicycles

are securely attached to the bicycle rack before you drive away.

Fig.3

Jack-It

Aftermarket Manual

www.lippertcomponents.com (574) 537-8900 Rev: 06.16 - Jack-It Aftermarket Manual

Manual information may be distributed as a complete

document only, unless Lippert Components provides explicit

consent to distribute individual parts.

All manual information is subject to change without notice.

Revised editions will be available for free download at www.

lippertcomponents.com. Manual information is considered

factual until made obsolete by a revised version.

Please recycle all obsolete materials and contact Lippert

Components with concerns or questions.

Notes

Indice

Altri manuali Lippert Components Accessori per automobili

Lippert Components

Lippert Components Solera Power Awning Manuale per l'uso e la cura

Lippert Components

Lippert Components OneControl Hotspot Manuale utente

Lippert Components

Lippert Components Kwikee Manuale utente

Lippert Components

Lippert Components Solera Istruzioni per l'installazione

Lippert Components

Lippert Components Ground Control 3.0 Landing Gear Manuale utente

Lippert Components

Lippert Components Edge Manuale utente

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components In-Wall Slide-Out Manuale utente

Lippert Components

Lippert Components SOLERA SLIDER Manuale utente

Lippert Components

Lippert Components COACH STEP Guida all'installazione

Lippert Components

Lippert Components SolidStep 3.0 Premium Step Manuale utente

Lippert Components

Lippert Components Sliding Swivel Seat Base Manuale utente

Lippert Components

Lippert Components X-Trek Manuale utente

Lippert Components

Lippert Components In-Wall Slide-Out Manuale utente

Lippert Components

Lippert Components Alumi-Tread series Manuale utente

Lippert Components

Lippert Components Happijack FT-DR2 Manuale utente

Lippert Components

Lippert Components Curt Rota-Flex Pin Box Manuale utente

Lippert Components

Lippert Components SolidStep XF Manuale utente

Lippert Components

Lippert Components ground control 3.0 Manuale utente

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Tire Linc Manuale utente

Lippert Components

Lippert Components Solera Slide Topper Manuale utente

Lippert Components

Lippert Components A-Frame Coupler Istruzioni per l'installazione

Lippert Components

Lippert Components Jack-It Manuale utente

Manuali Accessori per automobili popolari di altre marche

James Baroud

James Baroud Odyssey Manuale utente

Motorola

Motorola i50sx Manuale utente

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuale utente

Feniex

Feniex T3 Manuale utente

Renault

Renault 77 11 423 180 Manuale utente

Kia

Kia E8300-4D000 Manuale utente

Brink

Brink 756843 Manuale utente

Whispbar

Whispbar K085W Manuale utente

v.link

v.link CI-VL2-PC-HSD Manuale utente

Viking

Viking Stack-Rack Guida rapida alla configurazione

Aries

Aries 203015 Manuale utente

Choetech

Choetech AT0005 Manuale utente

ZZ2

ZZ2 ZZAIR-PRO Manuale utente

Holman

Holman 4A80L Manuale utente

Thule

Thule 2075 Manuale utente

Motorola

Motorola T325 Manuale utente

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guida all'installazione

DV8

DV8 FBJL-02 Manuale utente